I just setup two RV180W's in a gateway to gateway setup, and I've got an IPsec connection established, and from the one router at my house I'm trying to access our work network, and I can't get to anything, nor can I ping anything.
View 7 RepliesJust set up a ClearOS gateway - internet works, DNS everything OK.I can ping the two routers (set up as switches) but i cannot access them via the browser from my PC (CYLON). I CAN access ClearOS panel from my PC?
View 1 Replies View RelatedI've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...
View 0 Replies View RelatedI picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
'TECHNICAL' SPECS
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
[URL]
Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?
View 1 Replies View RelatedI have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.
View 2 Replies View RelatedNew hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
I have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc). I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity.
Routing does behave as advertised, where all traffic does go to the main office. However, the 192.168.1.0 subnet in the branch office does not get internet connectivity. I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet. Is there a way to configure the RV082 router to provide NAT for all subnets?
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets? Can the RV082 be used as part of the final solution or are my RV082s a wasted expenditure?
Following is the configuration that I'd implemented, (real IP and IKE keys are bogus).
Gateway To Gateway
Remote Main Office
Add a New Tunnel
Tunnel No. 1 2
Tunnel Name : n1-2122012_n2-1282012 n1-2122012_n2-1282012
Interface : WAN1 WAN1
[code].....
I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway. One location is a static IP Address. The other location is a dynamic IP address.
View 2 Replies View RelatedI am trying to set up a gateway to gateway VPN connection between a RV042G (central site) and a RV110W (newest firmware) which is used for presentation purposes on various customer's sites. The RV042G has a static IP. The RV110W has different IPs, depending on where it is used.
Basic VPN settings are clear to me (we have another VPN between two RV042G with static IPs). I set up the VPN connection on the RV042G wth the following settings for "Remote Group Setup":
Remote Security Gateway Type : IP + Domain Name (FQDN) Authentication IP by DNS resolved: mydomain.no-ip.org Domain Name: router12345
The value "router12345" is what I have configured in the RV110W as "Host name" in the network settings.
This configuration does not work so I am obviously doing something wrong. Do I have to use "router12345.mydomain.local" instead if I configured "mydomain.local" as the domain name in the RV110Ws network settings? For my tests the RV110W has a WAN-IP of 192.168.178.100 because it is located behind a DSL-Router. The external IP of this DSL-router is 178.0.x.x. The resolved IP from mydomain.no-ip-org is 192.168.178.100 but when I look in the RV042G log I see the requests coming withg the external IP (178.0.x.x). Is this the problem? The last message I see in the log is "no connection has been authorized with policy=PSK".
Or can I use "IP + Email Address (USER FQDN) Authentication" instead (where can I enter this email address in the RV110W?). Or do I have to use "Dynamic IP"?
Here is my setup:
Netgear WNR2000 router.
Macbook Pro with Snow Leopard connected to router through wireless.
Windows 7 Desktop getting internet through the MBP ethernet.
I can't figure out how to be a part of my "Home Network" with my Win7 Machine so I can see other computers in my house, use my networked printers, etc. I can only see the MBP it is connected to in network panel. I want to be able to stream the movies on this computer to my iPad which is connected to the wireless router.
I exchanged a RV042 v1.2 (Firmware 1.3.13.02) by a new RV042G v3. (Firmware 4.2.1.02).
My problem is now the following: The old RV042 established the Gateway to gateway VPN connection as soon as an IP- address of the remote location was requested. The new RV042G stays on „Waiting for connection“ all the time and does nothing at all. The connection works by clicking „CONNECT“ or by ticking Keep-Alive in the advanced tunnel settings but NOT automatically as before. Is this a firmware issue or have I to configure something additional?
I am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it.
When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need portforwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2
I have a RV042 and I am trying to setup a Client to Gateway VPN for about 12 to 15 remote users. These users travel a lot and need to connect to the server. I have never setup a vpn and have looked at the manual and set it up like it says to. I installed the Quick VPN client on the remote computer and copied the certificate to the remote computer.
I am having two problems.
1. When I run the client on the remote computer and try to connect it tells me the cert is not installed on the local computer. (it is copied to the root program directory C:Program Files Cisco Small Business and the sub directory, C:Program Files Cisco Small Business Quick VPN Client.
2. I can continue and it acts like it's connecting but it does not. If I look at the router VPN summary it shows that I connected for only a brief time.
I have a e4200 Linksys upstairs and the range in parts of house is weak weak. I need more access points. Can I add another router downstairs on another cat5 and make it act as access point? What other options?
View 4 Replies View RelatedI've got half a dozen RV042 routers in various locations. They are running v4.0.0.07. Seemingly randomly, I got the 502 Bad GatewayThe CGI was not CGI/1.1 compliant. error when attempting to log into the web interface with google chrome (same with IE too). This happens from the LAN side. I actually didn't notice it until my Opsview monitoring software threw up a critical when it didn't get an http response. The router is otherwise actually working just fine.Since the first occurrence, more of my routers have developed the same error.
I've tried different browsers, clearing caches, though I'm not surprised those efforts were fruitless, as there is clearly a problem even when no browser is involved (nagios). The nagios http check also returns a 502 Bad Gateway.
I'm having problems setting up VLANs on my RV110W Small Business Router. I have updated the firmware to the latest : 1.1.0.9 Here is my set up :
WAN settings :
IP : 192.168.1.252 / 255.255.255.0 - Gateway 192.168.1.254
VLAN1 (default) :
IP : 192.168.2.254 / 255.255.255.0
VLAN3 (test) :
IP : 192.168.16.254 / 255.255.255.0
Inter-VLAN routing option is checked.
Symptoms :
- The communication from VLAN1 to WAN is fine
- The communication from VLAN3 to VLAN1 is fine
- The communication from VLAN1 to VLAN3 is not working
My routing table is :Routing table Entry ListDestination LAN IPSubnet MaskGatewayInterface192.168.2.0255.255.255.0192.168.2.254LAN192.168.1.0255.255.255.0192.168.1.252WAN192.168.16.0255.255.255.00.0.0.0LAN0.0.0.00.0.0.0192.168.1.254WAN
As you can see, the gateway for VLAN3 is set to 0.0.0.0, which is wrong I believe. I don't know how to update that. I tried to add a a static route for the subnet, but the router did not let me do that.
I gave setup a vpn gateway between two cisco RV120W. The connection is established.
Active IPsec Security Association Table: Policy NameEndpointPacketsKBytesStateActionRxTxRxTxVPN-INTERDIO87.65.38.62000.000.00IPsec SA Established Poll Interval: (Seconds)
The problem is that there is no trafic. Even ping te remote internal nework is not working. For testing i have disabeld at both sites te firewall and have configured both with an access rule any to any.
I set up an RV042 as a VPN gateway for a client a year ago. It is running firmware 1.3.12.19-tm (Feb 13 2009 13:03:21). I created a new certificate. When I download the client certificate, It comes as a .zip file. One the can not be opened by a zip utlity (windows, Winzip or 7 zip). It looks like I can just rename the file to a .pem file, but I want to make sure that is right. They were getting QuickVPN timeouts, but that looks like it was fixed in 1.3.13.
View 3 Replies View RelatedI have RV042 on my remote network, i have problems with VPN connection , user can connect to RV042 but only inside IPs that can ping from vpn user.Is it any way to make the traffic from Rv042 will back to RV042 . maybe with nat.. in example below 192.168.5.100 is my lan IP from my DSL dhcp, and 172.27.0.20 ip on remote, traffic not back to my pc/vpn client, what i want is to translate 192.168.5.100 to RV042 LAN ip address
1485: ICMP echo request (len 32 id 256 seq 29) 192.168.5.100 > 172.27.0.20
1486: ICMP echo reply (len 32 id 256 seq 29) 172.27.0.9 > 192.168.5.100
1487: ICMP echo request (len 32 id 256 seq 30) 192.168.5.100 > 172.27.0.20
1488: ICMP echo reply (len 32 id 256 seq 30) 172.27.0.9 > 192.168.5.100
[code]....
We have just purchased a license L-PL-GW-100MAX-3= Protect Link Gateway: Unlimited Web + 100 Max Email Seats,3YR. I found that it does not include IPS license. I cannot find anywhere where I can purchase an IPS license for SA540 gateway. It seems to be available only as a bundled product when purchasing the hardware.
View 1 Replies View RelatedI am able to access the internet. I am running Windows 7 on my laptop and have a wired connection between it and my intergrated router. The internet works fine, but it seems to think that I am not connected to the network. I'm not certain it realized that I even had a network, since when I try to activate media sharing it just gets stuck at "Identifying Network". The whole purpose of this is to be able to play music from my computer on my Xbox 360, alternative solutions for this goal would be good too.
View 5 Replies View RelatedI have created a connection gateway-to-gateway between RV220W and RVL200, is doing without any problems.For example, I can ping the gateway on the other side. But when I connect trough RV220W QuickVPN (or PPTP) I can not reach the gateway (RVL200) or any host behind it.
View 4 Replies View RelatedI have router Linksys RV042 v1.2 with latest firmware Version: 1.3.13.02-tm. And I'm using QuickVPN v 1.4.1.2. I've setup VPN connection with values, below: But every time I'm trying to connect to router by VPN it always popup a window "Remote Gateway not responding".It occurs when I'm trying to connect to VPN behind other router, when I'm connected directly to Internet the connection is established.But I'm connecting to other networks using VPN and it's working properly (behind the same router), so I think it's problem with RV042 configuration but I don't now weher.
View 5 Replies View RelatedI am trying to setup the following. We have an RV042 Router and are using it as our gateway at the office. In the office we are using a Windows Domain abc.lan with DHCP of 10.0.0 - 10.0.0.254. The Router/Gateway is setup with a Static IP of 10.0.0.100.A couple of our office employees would like to work from home via VPN using their laptops. With the many options available for this router, I am not clear as to which options and what settings I should set.
View 2 Replies View RelatedI have a RV110W which is am using as a router (not gateway), because it is connected to the DSL modem (not planning to bridge it) through its WAN port. The DSL modem forwards all PPTP traffic to the RV110W.The only pupose of the RV110W for me is to use it as a VPN router.
Info:
Firmware version: 1.1.0.9
Below are the settings I have:
WAN:
LAN:N.B. The modem runs a DHCP server, so I am relaying the requets to it
VPN:N.B. Also tried with 192.168.0.0 and 12.168.2.0 networks; same thing.
Routing Settings:
Routing Table:NB: 192.168.1.11 and 10 are VPN clients (created automatically).
Firewall:Users are being able to successfully connect to the VPN; however, there are couple of problems:
1. They are not assigned a gateway; hence, not internet connectivty (i want them to use the remote gateway)
2. They are not able to access the 192.168.0.0 network; hence unable to reach their DNS server and other hosts (run a tracert; they couldn't go beyond the RV110W VPN server IP). For this, i tried to turnoff the firewall on the RV110W, and also tried to create and Access Rule to allow all outboud and inbound traffic between LAN and WAN, but no success.
I am setting up a dual WAN network in our small business office and I am confussed on the set up of the RV042.
On WAN1 I have a satellite modem connected
On WAN2 I have a cradlepoint CTR35 Router with a verizon aircard
The satellite has lag issues and will drop out during poor weather but has a 17GB dowload limit. The verizon aircard has only 5GB download limit but normally works in poor weather. Code...
Do I select obtain DNS automatically on both WAN1 and 2? Do I set this up as a gateway or a router?
I am trying to install a Cisco VPN Router RV120W behind this router. I have setup the Cisco and can access the internet from the device. I also setup the Actiontec router with the DMZ host as the Cisco router. When I try to connect to the VPN tunnel however I connect but receive an "Gateway is not responding" error message after 30sec. Is there anything else I need to setup on the actiontec router to allow VPN passthough or something like that?
Actiontec Lan IP: 192.168.1.1
Cisco Wan IP: 192.168.1.2
Cisco Wan SN: 255.255.255.0
Cisco Wan Gateway: 192.168.1.1
Cisco WAN DNS: 192.168.1.1
71.250.0.12
Cisco Lan IP: 192.168.20.1
Edit: I have also tried this connection from a Windows 7 Pro with Firewall enabled and also Windows XP with the same error.
Quick VPN log:
2011/12/30 00:05:58 [STATUS]OS Version: Windows 7
2011/12/30 00:05:58 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/12/30 00:05:58 [STATUS]Windows Firewall Private Profile Settings: ON
2011/12/30 00:05:58 [STATUS]Windows Firewall Private Profile Settings: ON
2011/12/30 00:06:10 [STATUS]OS Version: Windows 7
2011/12/30 00:06:10 [STATUS]Windows Firewall Domain Profile Settings: ON (code )
I spoke with the Comcast gateway support team and they changed my SMC router to the straight gateway/bridge option. If I plug directly from my laptop to the SMC, I have internet connectivity. So I know that aspect is working. I have a Cisco RV220W router that I want to be between the internet/SMC gateway and my network. For the life of me, I cannot get the internet connectivity to pass through to the router. I've done the proper power on order numerous times. Tried variations just for the heck of it. And nothing. Am I missing a step? If I do the "wizard" on the router, it basically tells me it sees no gateway even available even though it is clearly there and plugged into the WAN port. I don't see any option in the router settings for me to specify like the DHCP server I should be reaching out (if there even is one). My understanding is I shouldn't need to as the router should just recognize it. Should I be using a static IP instead?
View 3 Replies View RelatedI recently purchased a RV110W wireless router for a client. I am having issues with the VPN access. Here is the client's access log:
2012/04/17 10:59:41 [STATUS]Disconnecting...2012/04/17 10:59:47 [STATUS]Success to disconnect.2012/04/17 11:00:03 [STATUS]OS Version: Windows XP2012/04/17 11:00:03 [STATUS]Windows Firewall is OFF2012/04/17 11:00:04 [STATUS]One network interface
[Code].....
I've called Cisco tech support but the answer is disregard the log message and everything is working, and that I have a configuration issue on my end.
I have a public IP (static). I have a Gateway machine which is connected through a modem. When I want to add that public IP to the Gateway Device through [URL] site.
View 3 Replies View RelatedI have 12 computers in Local Area Network, I am using 3MB DSL broadband, all PC using XP SP3 connected through D-Link Switch with IP address 192.168.0.201 to 192.168.0.212, The D-Link router gateway is 192.168.0.1Network diagram is as followsADSL modemouterIPC1, PC2, upto PC 12My problems are.1. All PC cannot access Internet, So I reset the modem, wait for a few minutes, if I am lucky, Internet comes back, sometimes have to wait longer 15mins or 30 mins2. PC12 is used for monitoring, but cannot see PC 1, the rest can see.When I try to ping, time out, but after sometimes....it came back, I can see PC 1, then disappear again.How do I solve this problems?Note, the ADSL modem provided by the Service provider looks normal, with Power, Ethernet and DSL lights ON.
View 15 Replies View Related