Cisco Routers :: Wrvs4400n V2 DDNS Not Updating When IP Address Changes
Apr 19, 2013
I have two of the Wrvs 4400n V2 VPN (V2.0.2.1-ETSI) routers in different countries, one in the UK and one in Australia. They are permanently linked using the IPSec VPN tunnel and the dynamic DNS feature (DynDNS.org). I have found that the router in the UK does not update its IP address automatically to the dns website when the UK Internet service provider changes the WAN IP of this router. This makes the IPSEC tunnel go down until I telephone the UK location and ask to force the router to update its IP address with dyndns by restarting it or by using the routers configuration to re-save the password for dynamic dns.
View 2 Replies
ADVERTISEMENT
May 28, 2013
I have been struggling to find a DDNS provider from which the IP address can be updated from a Cisco device.One does not seem to support it, (Free-DDNS) other must be paid for (No-IP.org) while the free version does not update the IP address in my case, etc, etc.The device that is directly behind my modem is a Cisco 1801 router.My question is, which DDNS provider works for you when auto-updating the IP address via the Cisco router?
View 1 Replies
View Related
Oct 26, 2011
Since firmware 1.0.3 it seems my DDNS is not updaing with DynDNS since the last update.
View 2 Replies
View Related
Jan 5, 2012
I have a conflict with my satellite Internet connection between the modem and router IP addresses. I also somehow entered a password for the router which I now cannot duplicate. received a request for additional information which I responded to in September. I attempted to follow-up in October again, but I have not received any reply since the first one on August 11, 2011.
View 1 Replies
View Related
Dec 3, 2011
I updated my firmware to the latest update a and then restored My personnel setting and now I can not access my ftp, I checked my IP address to make sure it didn't change , setting looks like did before update I went from firmware 121 to 135, was there new setting that I have to change to get it to work. I get no log in screen I get Windows cannot access this folder. Make sure you typed the file name correctly and that you have permission to access the folder?
Details:A connection with the server could not be established
View 2 Replies
View Related
Nov 26, 2011
I just purchased a RV016 router, upgrading from an older Linksys router only to find out that there was no support for TZO DDNS. I have used TZO for years now and don't really want to change to another service. Any way to request this from Cisco engineers for future firmware upgrades?
View 2 Replies
View Related
Sep 26, 2012
I am trying to set up DDNS for my network. Right now there are only RV180W for DDNS providers (DynDNS, TZO, and 3322).I wanted to use a free DDNS provider, however DynDNS and TZO are now pay only (or only a short free trial via credit card). 3322 seems untrustworthy, as Google is reporting that it is a security risk?Anyway, my question is: "Is there a way I use another DDNS service other than the ones offered by default in my RV180W?"
View 0 Replies
View Related
Sep 1, 2011
I am trying to set up my rv042 to use the ddns service. The rv042 is directly connected to the ISP provided modem on WAN port 1. The problem is that instead of seeing the internet IP the rv042 is using the ISP sub net assigned IP.
LAN IP : 192.168.1.1 WAN1 IP : 192.168.12.9 WAN2 IP : 0.0.0.0 Mode : Gateway DNS (WAN1) :DNS (WAN2) : 192.168.12.1 DDNS(WAN1 | WAN2) : Off | Off DMZ Host : Disabled
View 1 Replies
View Related
Apr 15, 2012
How to to successfully configure and connect to a DynDNS account with RVS4000? This was working fine for me until recently when I think I upgraded the firmware to 1.3.3.5.I am trying to connecting to DynDNS.org service. In the past, I used the following string for the Hostname which worked: 'mysubdomain.domain.com&system=custom' (including small quotes). According to the RVS4000 documentation, all you should have to do is specify the host name with DynDNS but this clearly is not accurate.
View 1 Replies
View Related
Feb 15, 2011
my RV042 is not able to propperly update my ddns. If you try to resolve my dyndns subnet kitus-network.dyndns.org you will get 192.168.0.2. How can I make the router update my ddns with the real public ip rather than the private ip it "sees" on the WAN interface?
View 5 Replies
View Related
Apr 20, 2011
i have a new smc router and my local ip address and remote ip addresses are very similar. The remote ip address is updating my dns server but i am unable to ping it. Its something like 122.61.xxx.1 ?
View 8 Replies
View Related
Jan 30, 2013
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.54317n
ISP : century link
How do I test my routers ddns? My computer went down. So, my adsl ip address changed. I caused the modem/router to reboot. But the new ip wasn't sent to the Host (dyndns.org). I had to update my ip manually on [URL].
View 2 Replies
View Related
Sep 5, 2011
will updating my RV042 firmware allow me to download larger files? How do I know what version to update to? Our current version is 1.3.7.4
View 1 Replies
View Related
Nov 30, 2011
I purchased 2 RV042's (h/w version 3) less than two months ago. I updated them to the latest firmware (v4.0.4.02-tm (Jul 4 2011 13:30:56)), did a factory reset to make sure I was working with a clean slate, set up DDNS through DynDNS and a site to site VPN between the two. Everything was working great for a month, then the DynDNS accounts expired because they weren't being updated. I reactivated the names on the DynDNS site, and started to monitor the "last updated" date and time. After 24 hours there were no updates according to the DynDNS site. I logged into one of the RV042's, and it said "Dyndns Enabled : Dynamic DNS is updated successfully." This is a stale message from 24 hours ago when I hit save. So I went into Setup | Dynamic DNS | Edit Config and there it also says "Dynamic DNS is updated successfully." I clicked "Save", status changed to " Dyndns Enabled : Updating..." for a few seconds, and then back to "Dyndns Enabled : Dynamic DNS is updated successfully". I refreshed the DynDNS website and it shows the current time (in eastern time, i'm pacfic) as the last time it was updated. So it works when I manually hit the "Save" button. Not making any changed, just hitting "Save". I've let the other RV042 go over 48 hours and it still hasn't updated. So it apears for the time being, I'll have to remember to push the "Save" button once a week to prevent my DynDNS accout from expiring. Does DDNS working in the lastest firmware and h/w version 3? If so, what is the update frequency?
View 6 Replies
View Related
Mar 22, 2012
why does my 2811 routers boot to rommon after uploadig IOS c2800nm-ipbasek9-mz.151-4.M1.bin
View 1 Replies
View Related
Sep 5, 2011
I just updated my RV042 to the firmware RV0XX-v4.0.4.02-tm-20110704-code.bin and now im having this error every time that i try to logon in the router? 404 Not FoundThe requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist.
View 7 Replies
View Related
Apr 13, 2012
I have a Cisco rv220w. I just tried updating the firmware. I used RV220W-Firmware-1.0.3.5.img. It rebooted, and now there is no DHCP and no access to anything. I tried the reset button for 10 seconds. That didn't do anything. The WAN and all the LAN lights light up. Power is on and solid. The light blinks alternating between the DMZ and the blank space to the right of wireless. How can I get this back to factory defaults?
View 5 Replies
View Related
Jan 29, 2013
I'm using a wireless g router (f5d7230-4) which for most purposes is fine? Specifically: 1. I can't seem to stream media content from my windows 7 pc to my lg tv (model 55 lw 6500), and wonder if the age of the router is part of the problem; 2. some iptv channels on my ps3 are slow to load menus, though programs run fine when I push play (I gather ps3 is restricted to wireless g but if I upgraded the router I would plug in the ps3 using cat6). When I speed test my internet connection I'll typically get results around 2.5-5 Mbps. I'm impressed that a router of this age performs so well it isn't obvious to me that upgrading will improve the setup.
View 1 Replies
View Related
Nov 10, 2011
My WRVS4400N, V2.0.2.1CPU:STAR 9202.Doesn't allocate IP address on DHCP for anything but the Open SSID. All others, WEP, WPA, WPA2, nothing.I tried different clients, Intel Centrino wifi, Cisco, AG-CB21 same results.The config is std, I tried one VLAN for ALL SSID, I tried different VLANS, same.
View 0 Replies
View Related
Jun 23, 2012
We have several remote sites with Linksys WRVS4400N and Smoothwall firewall/vpn devices. I need these sites to be able to connect to multiple dis-contiguous subnets at our main office. This was easily done with smoothwall and linksys. You create a separate tunnel for each subnet and voila, you're done. However, when I tried this with our newly installed ASA, it will not let me create multiple tunnels to the same remote peer address. This is a problem since these sites only have a single static public IP address. Am i missing something or does the ASA not allow connections to/from multiple subnets form a site with a single peer address?
View 13 Replies
View Related
Jan 24, 2013
I get a "IP address conflict" message on my wireless network. Using a WRVS4400n wireless router with the latest firmware that is set to PPoE. Motorola 336 dsl modem is set to bridge mode. My network has 2 computers attached: hardwire desktop and wireless connection to laptop. When I contacted ATT support, they said the problem is in the wireless modem. Are there some settings in the WRVS4400n that must be set to insure that each computer gets a different IP address?
View 2 Replies
View Related
Nov 8, 2009
I've been keeping an eye on my IPS report tab lately and have been watching a large number of ICMP_SMURF and DOS attacks originating from chinese ip address's. I know I can probably block the offending ip's through the ip based acl tab in the firewall settings, but I'm kind of a newbie how I can block certain ip's from touching my router?
View 3 Replies
View Related
Jul 5, 2011
Right out of the box, the WRVS4400N [firmware v2.0.1.3] I just purchased says the WAN interface is DOWN; and it simply will not obtain an IP address from the Arris TM602G cable modem it is attached to. Internet still runs great on the old WRT54G. Is this WRVS4400 DOA? Or is there some arcane setting the quickstart guide overlooks? OR?
View 2 Replies
View Related
Dec 7, 2011
I'll just use the 4400n to provide DHCP to my two VLANs and then a new problem cropped up. I am unable to add a default route to the 4400n's DHCP server. It uses the 4400n's vlan IP as the default route. What I'm trying to ultimately achieve is to configure the 4400n as an access point for our "private" network on vlan1 and also "guest" access to the internet on vlan2.
View 12 Replies
View Related
Mar 3, 2013
I'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
View 2 Replies
View Related
Sep 16, 2011
Ive setup a few WRVS4400N over the past 6 months, and have been receiving the below message from some of them every couple of hours.What does the message indicate?
View 1 Replies
View Related
Sep 15, 2012
I have successfully got QuickVPN working from Windows 7 64bit into my WRVS4400n. The router is sat behind another router/modem (Belkin) as the UK uses PPPoA and the WRVS4400n doesn't.So I set up DMZ and changed the DHCP to always allocate 10.x.x.2 on the Belkin which is the WAN side for the WRVS4400n as it is the only thing attached.I have now noticed, and I'm not sure whether it was the case before, that the DNS that the WRVS4400 is showing is the LAN address for the Belkin Modem/Router (10.x.x.1), not 192.x.x.1 for the WRVS4400n itself. I assumed setting the Static DNS 1 on the WRVS4400n would do it, but it didn't?When I connect into the network with QuickVPN, the computer names do not show even though I have selected the option in QuickVPN?
View 1 Replies
View Related
Aug 8, 2011
Our business was looking at purchasing one of these Cisco routers and were curious if it supported WPA2 EAP-TLS?
View 2 Replies
View Related
Jul 23, 2012
I have 2 WRVS4400N's available to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies
View Related
Dec 16, 2012
Recently installed a WRVS4400N router on my home network. Prior to that I was using the wireless built into my FIOS router. I wanted something more secure so I went with the WRVS4400N. I turned off the FIOS wireless and am only using the cisco wireless.
Im having intermittent issues with the wireless. I have many things hooked up to my wireless including a HP printer and a Sonos system. Most of the time if I just open my ipad I cannot see anything else on my network including the printer. If I try to see the Sonos system can cannot, sometimes I can open the app on my iphone and then I can see it.
Sometimes I can see the printer and sometimes I cant. Sometimes when I do see it and then print to it, it will be gone before it even prints.
I don’t seem to have any issues thru the LAN connections.
Also, ive noticed that the wifi is much slower than the old FIOS box.
FYI, when I remove the cisco and fire back up the FIOS wifi I don’t have any problems at all at any time. And its much faster.
I have tried channel 6, 11 and auto. Also turned off IPC and still no change.
View 1 Replies
View Related
Aug 5, 2012
I have a gateway to gateway vpn (home-office) working fine for almost an year btw 2 wrvs4400n routers, This morning, the VPN tunnel was down. I clicked "Connect" from the web based interface, but it does not reconnect.
I tried setting up a new tunnel using the VPN setup wizard, but it says it can't connect to the remote router. Which is strange, since I can ping there normally.
View 2 Replies
View Related
Oct 15, 2011
I'm having a heck of a time connecting the WRVS4400N VPN to another WRVS4400N VPN. both of the routers have the current firmware version V2.0.2.1: Router 1 is below, and router 2 has the matching configuration with as it should be the local group being that routers local information and the remote crew set up being router ones information. the status is up on both of the routers, but I'm unable to ping the remote gateway or any device behind it.[code]
View 5 Replies
View Related
Oct 8, 2012
In setup for old RV042 (V1), when updating / adding Mac addresses, the table is always sorted by IP addresses. But in the new oneRV042 (V3) I have, even with latest firmware 4.2.1.02 the list is random, thereby increasing the chance of user entering DUPLICATE IP addr with diff Mac addr. That will result in conflict.If the firmware sorts the DHCP entries by ip addresses, user would be able to catch duplicate ip errors even if the system does not flag the errors. All Cisco smart engineers can you all get the dhcp entries SORT by ip addresses.
View 2 Replies
View Related
