Cisco Switching/Routing :: 2821 / Segment Shuts Down When Switch Plugged In
Mar 23, 2013
WAN link plugs into a 2821 Router with an switch module in it. About 8 clients are plugged in to the 2821.2821 connects to super cheap netgear switch (I'm 99% sure it's stripping dot1q headers) via one of the ports in the switch module. About 4 people are connected to the netgear.Now, I sent a catalyst 3560g to the branch because they wanted to extend into a new building. Someone decided to run a single cable from the netgear to the 3560. On the 3560, I have about 5 clients and a couple of APs.
So it goes 2821 -> Netgear -> 3560. All of these are single connections.When the 3560 gets plugged in, all clients on the netgear lose their connection, and nothing on the 3560 works. It happens almost instantly. I can't figure out why connections are dropping. The APs have about 4 VLANs onn them, and the PCs are on their own VLAN (the native VLAN).
View 3 Replies
ADVERTISEMENT
Jul 13, 2012
The default Gateway and DHCP server is connected to port 1 of the switch. I have various other devices on the network plugged into other ports on the switch.I want port 1 to communicate with every port on the switch, but don't want the other ports to be able to see eachother unless I specifically allow them to. For example, port 5 should see port 1, and 7, but nothing else.Everything needs to be in the same subnet. With the older Dlink switches I am used to this feature is called "Port Segmentation" but I see no such option in this switch. I have been playing with the VLAN settings but so far I have not been able to achieve this.
View 7 Replies
View Related
Dec 18, 2012
I have a 2821 router and need to add another Ethernet port.
However, all the Ethernet modules seem to be End of Sale and the suggested replacements are only compatible with the ISRg2 range.
View 2 Replies
View Related
Aug 21, 2012
We have an OSPF network with four 6500 Distribution Switches. They are fully meshed and see each other as peers and are sharing routes. Off of one pair (Border) there is a setup of 3750G siwtches that go off to another network and they do not run OSPF. Between the Border Dist and the 3750G Switches we run HSRP. The 3750G side uses HSRP GP 192 and the Dist Side uses HSRP 192.There are static routes on the 3750G pointing to the Dist HSRP address to get back to network.Pings fail from the OSPF side to the HSRP address on the 3750G side.If I do a trace from the OSPF side to the HSRP address it hits one border dist switch then the other and fails.If I have static routes on both border dist switches pointing to the HSRP on the 3750side, do we need to change the metric on one dist so that it is preferred over the other or should the router Id take care of that?
View 1 Replies
View Related
Sep 3, 2008
I have a 892 router configured on fa0 with vlan1 and a catalist 3560. On catalist all ports are in access mode and vlan1. When I'm connecting port fa0 from router to catalist, the catalist port is shuted down What should I do on router on catalist to make the connection working ?
View 4 Replies
View Related
Jun 6, 2013
I recently installed a cisco 2901 router. The router is connected to hosts using a SG 200-50 50-Port Gigabit Smart Switch
Problem is the router internal interface keeps shutting down without notice and randomly. At that time I cannot ping the interrface from a LAN PC even though I can ping other hosts on the LAN. The ISP link is okay since I can put a static IP on my computer and access the net.
View 8 Replies
View Related
Oct 21, 2012
How I can shutdown a module when I am running vsl.I can use the following command #hw-module module 2 shutdown.As I have modules in both switch 1 and switch 2 how can I ensure I only shut down module 2 in switch 1.
View 1 Replies
View Related
Feb 27, 2013
I have not been able to figure out the resolution. The basic premise is to have 3 inside vlan networks controlled by a 1900 series router. Then have that primary LAN router connect to the inside of my ASA5505 Basic, then go out to my ISP Gateway. I have tried hundreds of different static route configurations on my router and asa. I have tried equally as many NAT and PAT configurations, but nothing seems to work. I have even tried using all the commands (specific to my topography of course) on this weblink from cisco: url...
View 12 Replies
View Related
Feb 23, 2011
I have a Cisco C3560G-24TS Switch that has twice now just shut down and the only way to get it back to life is to pull the power and let it boot back up again.
Are there any logs I can check for poss clues as to why this is happening or any other things I can try?
View 5 Replies
View Related
Aug 27, 2012
I have a Cisco Wireless LAN Controller WCL2112 model. It's currently plugged into an HP Procurve switch on a trunk port. That HP switch is plugged into my Cisco stack on a trunk port. I can reach the WCL just fine through the LAN. But when I plug the WCL directly into the Cisco stack on a trunk port, I can't reach the WCL at all, unless I connect to it over wireless. The interface shows it's conneccted and up/up. But no communications are sent across the line. I did a wireshark and can see only ARP request from the WCL. The trunk port on the stack is set to:
interface GigabitEthernet1/0/1
switchport trunk encapsulation dot1q
switchport mode trunk
The WCL has 3 VLAN's on it and the SSID of VLAN 1 is our office wireless. If that matters. .The Cisco Stack is 4 switches. cisco WS-C3750X-48P
View 3 Replies
View Related
Aug 13, 2012
I'm trying to enable port security on several 4507R's. When I try to configure a range of ports the switch will randomly put 1 or 2 in err-disable. It's different every time I apply the config to the same group of ports. However if I do them one at a time it seems to work. But I really don't want to configure 6 fully populated switches one port at a time. We also have a lot of 3750's and they gave me no problem using a port range. [code]
View 4 Replies
View Related
Oct 3, 2010
We've got a cisco 2821 router which periodically stops routing all traffic. It seems to happen about once every 2 weeks, and I can't find anything that could be causing it. There are no entries in the log and the router stays up and running but requires a restart to begin processing traffic again. We're running 12.4(13r)T11.Any thoughts, or troubleshooting steps to track this down?
View 7 Replies
View Related
Mar 12, 2013
I start configuring Cisco 2821 router for multicast . First short description and attached sheme explanation. Let we say I have small network with 100 users. One router and Cisco switch 3560. Two VLAN’s, one for data another for multicast. Data from internet works fine but now I want to connect multicast servers (or source of more multicast streams) from another subnet. Router have three interfaces.I expect there should be no problems with multicast configuration, but unfortunately it is not like I expect. What I did ?
First step: enable multicast routing
Second step: on both interfaces (Fe 0/1 and Fe 0/2) - ip pim sparse-mode
Third step: configure switch that users are connected to access port in VLAN 222 (temporary to see if multicast work)
When I start VLC on computer nothing happend. If I try to connect computer on same subnet where is source of multicast streams it works fine.What I am doing wrong ? Is there anything about routing ? All subnets are directly connected. RP is not needed if I have one router or ?
View 11 Replies
View Related
Jun 25, 2012
I have just bought myself a Cisco 2821 ISR.At present in my home I have a Cisco 2621XM. Fast Ethernet 0/0 is connected to a 3524XL as a trunk to provide my LAN with inter-vlan routing. it works great. Fast Ethernet 0/1 is connected to my ISP's cable modem and uses the command "Ip address dhcp" to get an IP and all other info from my ISP.FA 0/1 is Ip nat outside and the FA 0/0 and all sub interface like 0/0.1 .24 .168 etc all ip nat inside.I get intervlan routing and access to the internet via this router.I have this 2821 to replace the 2621XM as I plan to run CME on it and want gigabit routing on my vlans as at the moment on the 2621 routing between vlans it at half duplex or seems to be.I have configured the 2821 to ip nat outside on gig 0/0 and ip nat inside on gig 0/1 and all of the sub interfaces (same setup as my 2621 but with gig ethernet)I have no access to the internet at all but I can ping www.google.co.uk and other domain names from the terminal session when I am connected to the 2821 via the console or telnet/SSH. the gig 0/0 has an IP assigned from my ISP too but no other nodes on the network can ping outside.Am I missing something here? the version of IOS is V 15.
My access list goes someting like
access-list 1 permit 10.0.0.0 0.255.255.255
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 100 permit ip 10.0.0.0 0.255.255.255 any
access-list 100 permit ip 192.168.1.0 0.0.0.255 any
and so on
I still cannot access the internet.....
View 5 Replies
View Related
Jun 7, 2012
I have a Cisco 2821 Router. Its ethernet Interface(E1) is connected to an ISP's Gateway.The outside interface IP is 207.x.x.1, The ISP has given 6 public IPs (202.x.x.1- 202.x.x.6) to use in LAN.
I have configured the router`s Internal Interface(E0) with a public IP address. (i.e. 202.x.x.1)
My Internal LAN PCs are in a private range of 192.168.1.0/24 subnet. Now I wanted my PC users to access the Internet while the Routers public IP remains on internal interface. How can I do the same?
View 6 Replies
View Related
Dec 6, 2011
I have a 2Fe-2W Card and wanted to find out if it can be picked up and installed on a Cisco 2821? Below is the version
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(8a), RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2006 by Cisco Systems, Inc.
ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)
System image file is "flash:c2800nm-adventerprisek9-mz.124-8a.bin"
View 1 Replies
View Related
May 29, 2012
According to my boss every 3 to 4 months he has to restart our 2821 with a 16-esw module installed because of a low memory issue dealing with CEF. Here is the exact error message.
%% Low on memory; try again laterJun 8 11:18:51.777: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:19:51.823: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" %%
Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
Jun 8 11:20:51.868: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:21:51.914: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed
View 4 Replies
View Related
Jan 27, 2012
I have a 5412zl 10.215.x.x/16 Most of the connections on this switch are on vlan1. B9 is the port which is connected to a Cisco 2821 Router. The port on that end is GE0/1. The port on the cisco side is not a trunk but configure with an ip of 10.215.1.30/24 Its part of a some ip access group. The network that i now sit on is a 172.x.x.x/24 (behind cisco router, about 3 hops to that main 2821)We current have a system on my side that talks to a server on the 10.215. that has no issues. I'm trying to access some switches on the 10.215. and have had no luck reaching them.
Here is the access list that i found that port is configured to use:
permit ip 10.215.0.0 0.0.255.255 172.18.0.0 0.0.255.255 permit ip 10.254.0.0 0.0.255.255 172.18.0.0 0.0.255.255 permit ip 10.215.0.0 0.0.255.255 172.14.0.0 0.0.255.255 permit ip 10.254.0.0 0.0.255.255 172.14.0.0 0.0.255.255 permit ip 10.215.0.0 0.0.255.255 192.168.2.0 0.0.0.255 permit ip 10.254.0.0 0.0.255.255 192.168.2.0 0.0.0.255 permit ip 10.215.0.0 0.0.255.255 192.168.20.0 0.0.0.255 permit ip 10.254.0.0 0.0.255.255 192.168.20.0 0.0.0.255 I would think the first permit would allow me to get through to the 10.215 side but maybe i need to set something up on the hp size to let it know how to get back? I'm very new to this stuff.
View 3 Replies
View Related
Jul 31, 2012
I have 2821 router configured with two subinterfaces. This router is connected on cisco 2960 switch. The trunk on 2960 is configured without any prunning of vlans. I noticed that udp broadcast traffic is being forwarded through my router on native vlan 1 (this interaface do not have ip address configured). Below is configuration:
Router:
interface GigabitEthernet0/0
no ip address
duplex auto
[Code]....
View 6 Replies
View Related
Jul 2, 2012
Currently I have a network that looks like this:
ASA5510 - - - Internet - - - ASA5510
| |
EIGRP EIGRP
| |
2821 -----------MPLS----------1841
BGP
The MPLS connection is currently down, I'm trying to run a failover Site-to-Site VPN over the internet. All of the examples I've read have both connections involved in the failover coming out of one device. Since I'm not working that way, what is going to be the best way to failover? Do I need to set up some sort of IP SLA in the config? Or can I somehow weight routes in EIGRP in a way that the connection will failover from Internet to MPLS when the MPLS goes down and vice versa when the MPLS connection comes back up?
View 2 Replies
View Related
Mar 10, 2013
What is the maximum VPN Clients that could be connected to cisco router 2821, with this IOS c2800nm-adventerprisek9-mz.124-20.T.bin
View 3 Replies
View Related
Jul 23, 2012
My 2821 router has an arp table with the wrong ip to Mac mappings. The impact is that I can reach any host in the 10.1.1.1 subnet. I can reach hosts in the 192.168.35.0 just fine. [code] It is as if the 192.168.35.1 device is answering all arp requests as a proxy arp or something. Clear arp-cache nor clear ip arp on my 2821 have any affect.
View 1 Replies
View Related
Sep 8, 2012
I need to configure a subinterface eg g0/0.1 and g0/0.2 with a untagged VLAN for each subinterface on a Cisco 2821.
View 5 Replies
View Related
Nov 13, 2012
Yesterday my router was hangs and my services was stuck. I start the router hard booted and it works fine.This was second time i was facing this kind of scenario. The attached are the "show tech support" of the cisco router 2821.
View 2 Replies
View Related
May 14, 2012
I have a cisco 2821 router in rommon and displaying the message '' softwre forced crash '' and '' checksum error'' .I tried to do rommon tftpdnld but as the image is self decompressing into the ram it again crashes with the same error although i have done it with various valid ios but in vain.
View 1 Replies
View Related
Apr 15, 2012
I have a 2821 Router, with a VWIC2-2MFT card in it, with two T1s going into that card. The two T1s are a bundled MPLS line.
I then have a cable modem connection going into the gigabit Ethernet GE 0/1 port on the router.
Right now, the cable modem provides a backup connection in case the T1s go down.
What I was wondering is if there was a way to 'combine' the bandwidth from the two T1s with the cable modem?
View 4 Replies
View Related
Apr 3, 2012
Basically I run 3 voice gateways on 2821 routers. In two of my routers I've had fan failures, one router has had two fans die and one has had just the one.
I was going to buy the offical Cisco fan replacement kit but then I thought with such as high failure rate I'd rather buy something else and better guarentee the service to my call centres.
So, what i'm asking is:
- Is there any reason why I cannot procure a standard 80mm 12V fan with a better rating (cooling and reliability) and install this in my 2821's?
I understand this may invalidate any warranties but mine have long expired.
View 1 Replies
View Related
Mar 17, 2013
I've 3 interfaces on router:
Gb0/0-ISP01 with DHCP client
Gb0/1-ISP02 Static IP 192.168.2.x/24
Fa0/0 - LAN 192.168.1.1/24
I want to know, how to configure:1. Set the IP of interface Gb0/0 as dhcp client from ISP01 and make it as default route.
2. How to configure the ip nat.....overload?
3. How to use the ip sla to monitor internet connectivity to 8.8.8.8 for ISP01, if it fails, to go to ISP02.
View 3 Replies
View Related
Sep 25, 2012
We've got Cisco 2821 for our 90mb/s Internet Access. Its CPU usage is around 80%. Show process cpu does not show any cpu proccess with high utilization. But we have got plenty of policing configured for our clients using policy maps. Can this policing affect cpu usage?
View 1 Replies
View Related
Apr 8, 2013
I am having an issue pinpointing why my 2821 router is discarding so many packets when transferring data to our second site. The traffic flows from the local lan, to the router, where it is redirected via WCCP to a WAN optimization device, back to the router and over a GRE tunnel to the second site where the same process happens. The traffic does get there, but the LAN/Repeater router interfaces have around 20,000-60,000 input drops an hour. From the output below, it looks like traffic is being dropped by the RP.
I just restarted the router as a last resort, and here is what has accumulated in the last 30 min:
FastEthernet0/0/1 is up, line protocol is up
Hardware is Fast Ethernet, address is 0025.840c.7680 (bia 0025.840c.7680)
[code]....
And CPU never goes above 40%
100
90
80
70
[code]...
View 17 Replies
View Related
May 5, 2013
I have customer that we have configured netflow on the 2821 router that their traffic is on. Currently the company they have contracted with for the analysis is seeing data duplication. Below is the configuration for the interface and the router
Cisco 2821;
interface GigabitEthernet0/0
description TVC-FI-Ethernet-Fiber-Ethernet link
ip address 216.255.164.33 255.255.255.248 secondary
ip address 192.168.5.1 255.255.255.0 secondary
ip address 216.255.166.129 255.255.255.128 secondary
[code]....
View 2 Replies
View Related
Jan 16, 2012
this router of my girlfriends only works when iplug the dsl modem into the output ports what could possibly cause this. would a firmware upgrade straighten it out...
View 1 Replies
View Related
May 9, 2012
I start configuring Cisco 2821 router for multicast . First short description and attached sheme explanation. Let we say I have small network with 100 users. One router and Cisco switch 3560. Two VLAN’s, one for data another for multicast. Data from internet works fine but now I want to connect multicast servers (or source of more multicast streams) from another subnet. Router have three interfaces.I expect there should be no problems with multicast configuration, but unfortunately it is not like I expect. What I did ?
View 10 Replies
View Related
