Cisco Switching/Routing :: IPv6 RIP Not Being Learned ME3600
May 20, 2013
I have a very basic setup here but strange the router is learning RIP routes advertised by the switch but the switch is learning anyRIP routes. Debug shows the switch is sending updates but not receiving any. There is also these error: %MRIB_API-3-ASYNC_ERR: Asynchronous error: failed to register to the MRIB. errno 0xE
I can ping across the gig 0/2 (switch) and GIg 0/2/0 (router)
sw01 - ME 3600
rtr1 - ASR 1001
sw01 config
[Code]......
View 4 Replies
ADVERTISEMENT
Mar 18, 2012
I use IOS Software, ME360x Software (ME360x-UNIVERSALK9-M), Version 12.2(52)EY2. I not found the command "ipv6" on global and interface configuration.
View 2 Replies
View Related
Apr 24, 2013
i have some ME-3600x. some of version 12.2 and one of version 15.5. te last one hast same config as all other. but if i check for rstp it sends.i know abount global config commands:
-spanning-tree mode rapid-pvst
-spanning-tree extend system-id
but there is no spanning-tree support. this causes many more problems. so it is important to solve spanning tee at first.is it possible without downgrading this device?
View 3 Replies
View Related
Jul 10, 2012
Which IOS version for me3600 supports 4-byte BGP?
View 1 Replies
View Related
Mar 27, 2013
I faced with a strange behavior of ME3600.For testing purposes I linked Cat3550 and ME3600 switches via trunk mode. All interfaces are in Up state. But I couldn't ping SVI200 of Cat switch from ME3600 and vice versa. [cde]
This scheme perfectly works with another L3 swithes. For example Catalist3750. I know that ME doesn't support VTP, DTP and so on. Also, I've tried latest software.
View 0 Replies
View Related
Nov 11, 2012
I'm looking to try and implement ipv6 HSRP on a series of IOS-XR Routers running 4.2.1 following on from successfully setting up IPv6 HSRP on a few cat6509s on VLAN Interfaces in other parts of the network. I have entered the "router hsrp" configuration menu and gone into the interface in question that I'm looking to setup with IPv6 HSRP. Unfortunately, there version 2 or address-family ipv6 commands are not available.
View 2 Replies
View Related
Nov 28, 2012
I need to know the 172cisco 1 router support to IPv6 & it support to IPv6 then which IOS is required for it.Also I need to know the cisco 2960 switch is support to IPv6?
View 3 Replies
View Related
Aug 8, 2012
Just I have upgraded some 2960S to IOS 15.0(2)SE from a IOS 15.0(1)SE3 and the catalyst don't switch any IPv6 traffic. Don't work any RA and also don't work any unicast IPv6 traffic from any interface. I can see some references to IPv6 changes in the FHS (First Hop Security) in the Release Notes, but no any reference to changes in the configuration.
The switches don't have any IPv6 specific configuration and the sdm is the default templata. Returning to 15.0(1)SE3 everything work ok.
On Catalyst 2960, and 3560E this IOS version seem to work fine with IPv6.
View 1 Replies
View Related
Dec 13, 2011
I've a 3750-48ps-s running ios version: c3750-advipservicesk9-mz.122-46.SE.bin
I've tried to configure ipv6 on an interface but it does not give me the option.
How do I know if my ios is IPv6 capable?
View 1 Replies
View Related
Mar 2, 2013
I have cisco 2960 and Catlyst 4510 switches now we are planning to implement IPV6.
i have the fallowing IOS on my switches.
C2960-lanbasek9-mz.122-50.se5
Cat4500e-entservicesk9-mz.122-54.sg1.bin
The above ios will support for IPV6 or I have to purchase new IOS, which version will support.
View 1 Replies
View Related
Jan 3, 2012
Trying to control capacity utilization for guest users connecting to a 2960 switch. No problem for IPv4 users, but IPv6 is giving me fits. What I've found out by trial and error so far implies that there is just enough IPv6 smarts in a WS-C2960-24TT-L running c2960-lanbasek9-mz.150-1.SE to make it impossible to control IPv6 traffic. Blocking IPv6 would be sufficient short term, but MAC filtering on type 0x86DD does not appear to work either. Here are the results I've gotten so far:
What "works":
* Protocol ipv6 or an IPv6 ACL in a class map.
* Using a class map referencing ipv6 protocol or an ipv6 ACL in a policy map.
* IPv4 inbound filters and policing.
* Blocking of IPv4 traffic by a MAC ACL blocking type 0x0800 (IPv4) - note that the docs explicitly state that MAC filters do NOT filter IP traffic, except for on this box on this release they do.
What does not work:
* Applying a policy map referencing a class map referencing protocol ipv6 or an IPv6 ACL to an interface. The service policy is accepted by the parser, but is not inserted into the running configuration.
* "class-default" in a policy map only matches IPv4 traffic, not all other traffic.
* Blocking of IPv6 traffic by a MAC ACL blocking type 0X86DD. No problem applying the access-group to the interface, it just doesn't do anything.
I am aware that this box is not supposed to support IPv6 other than for multicast, but as implemented, this is a hole an abuser could drive a MAC truck through.
My questions:
Is this situation unique to this particular 2960 switch or SW release (I also tried 12.2(58)SE2) or does it afflict all 2960's running LANbase?
Assuming the answers to the first two question are negative, what is the minimum requirement to get working IPv6 policing in an edge switch?
View 0 Replies
View Related
Aug 30, 2012
I've several production Catalyst switches that are listening on the same IPv4 and IPv6 ports. The problem is I don't want the switches listening on the IPv6 ports.[code] How to shut down these listening ports?I also have a few production switches listening on UDP/10000 and I cannot determine why this port is listening. [code] I've seen where UDP/10000 is Network Data Management Protocol and is related to Storage networks ###, but I've also seen where UDP/10000 is the default port for IPSEC data.I don't believe UDP/10000 is related to either NDMP or IPSEC data, though I could be very wrong.
View 4 Replies
View Related
May 23, 2012
I have seen other discussions regarding Static MAC address entries on IPv4, but what of IPv6?We have MS NLB solutions and they are working fine. We have Cisco 6509/6504, Version 12.2(33)SXI5
But then we have a new one for a new ActiveDirectory solution, and on those networks we have implemented IPv6.
How is Static MAC address entries and MS NLB solved in IPv6 (i.e arp ip.ip.ip.ip mac.mac.mac ARPA gi1/1). I can't seem to find much examples or documentation on this? Is it replaced with another function?The reason I ask is twofold.
1. I really want to know
2. The NLB cluster seem to drop IPv6 traffic at even intervals, witch seems to correspond with NLB transition.
View 1 Replies
View Related
Feb 18, 2013
There are two kinds of time for assinging IPv6 address from DHCP server.Actaully Catalyst 3750X can do this role. however I am not sure about the difference between Valid lifetime and preferred lifetime.In my understanding the valide lifetime is total lifetime for using the assigned IPv6 address but the prefered lifetime when the assinged IPv6 address is expired at the prefered lifetime then the device may generate extended request or something right?
View 1 Replies
View Related
Feb 18, 2013
I am having WS-C3560G-48TS switch with ios(c3560-ipbasek9-mz.122-58.E2.bin) and I am trying to use IPv6 feature in this switch model. More over I've upgraded this switch with many ios but none of them not supporting IPv6 feature. ios which supports IPv6 feature?
View 3 Replies
View Related
Nov 3, 2012
Need to confirm if WS-C3750-48TS-S supports Private vlans and IPV6?
Also need to know which stack cable like part number i can use for stacking them .
View 3 Replies
View Related
Jun 25, 2012
I have the cisco 3640 with IOS Version 12.2(46) , and it with DRAM:32M , Flash:8M.What IOS version can support IPv6 RIP in the hardware limit?
View 3 Replies
View Related
May 18, 2011
I have a situation where my Internet edge routers learn 0.0 from ATT (AS 7018) my provider. I then wish to advertise these learned routes via WAN. However my WAN MPLS provider is also ATT and they use AS 7018 for that as well. When I try to push 0.0 to my other WAN sites 0.0 is suppressed to avoid loops.What's the best way to tell the WAN routers to advertise 0.0 back to the same AS originally learned from?
View 16 Replies
View Related
Aug 29, 2012
There is nice c2900PortNumberOfLearnedAddresses table in C2900-MIB, but it's outdated and not supported by modern switches.Is there similar table for modern switches? Most interested in Catalyst 2960 and 3750.
View 2 Replies
View Related
Mar 21, 2012
I have two sites connected to each other using L2 MPLS/1Gbps "provided by the telecom", the link is configured as a 802.1q trunk and terminated on C3750 on both sites. Everything is working fine according to the below configuration. But i am facing QoS limitations on the number of queues, i checked cisco web site and found that the ME3600/3800 has HQoS which will give me advanced QoS features.I am thinking to migrate from the 3750 to ME3800, but i am new to metro switches. if i can apply the same below configuration on ME3800 except the QoS as i will replace it by MQC configuration? So can I consider that the ME3800 has all 3750 features plus MQC QoS?
!
!!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log datetime
[code]....
View 9 Replies
View Related
Feb 27, 2013
I have a few questions regarding IPv6.
Question 1.
I have no idea how to route IPv6. My provider has provided me with a subnet. This subnet is for example 1:1:1::/48
The router of the provider is located at 1:1:1::1 and my router should get 1:1:1::2(Cisco router). Every subnet I want to create must be routed by 1:1:1::2, for example if I want to create 1:1:1:1111::/64 it needs to be routerd by 1:1:1::2
How do I configure this on the RV220w?
Question 2.
I have the possibility to create vlans on the RV220W. I can configure IPv4 addressen per vlan. Only for IPv6 this is not possible.How do I configure this or when will new software be released to configure this?Or do I have to edit the configuration file?
View 2 Replies
View Related
Feb 16, 2011
The whole thing about IPv6 has been out for what is probably a couple of years now. But I find it very odd how even my newest modem/router can't even support it yet. Why on earth are manufacturers such as Netgear holding back so much on making their products IPv6 compatible? The IANA has just about given out what is left of the addresses, and we still have time to adapt by working our way over to IPv6 as it can work simultaneously with IPv4. Companies have been given years to prepare.
Why can't I connect to the Internet right now using IPv6? Not only is my router holding me back, but will my ISP hold me back as well?
View 1 Replies
View Related
Aug 1, 2012
I want run IPV6 multicast routing on Cisco 6506 device, I know i can activate IPv6 multicast routing globally but , Is it possible to run ipv6 multicast routing on interface vlan XXXX ?
View 1 Replies
View Related
Jan 15, 2011
I have a really weird issue with my cisco catalyst 3560G.
-device: cisco catalyst 3560g
-ios: 12.2-53(SE) IP SERVICES
scenario: configured IPv6 iBGP link between this switch and a router. the router is announcing 1 (test) route. the switch sees the route properly, but doesn't add it to routing table (the route never gets to be "best path", although it should be).
View 15 Replies
View Related
May 2, 2012
Why can't I set an IPv6 address here (WS-2960-48TC-L latest IOS)
View 7 Replies
View Related
Oct 23, 2011
So I've got a IPv6 tunnel with Hurricane Electric and it's currently physically segmented off of my home network. A 1841 terminates the tunnel and if I want to use it I need to plug into a port thats on a VLAN with no SVI and connect outbound to test IPv6 stuff. I'd like to give access to some other users and Im wondering if 6 over 4 tunneling with AnyConnect will work for that. My thought was that they could terminate on my main firewall (5505) and then terminate their VPN session in another vlan which was connected to the IPv6 router. I have this config working right now with IPv4 and I can browse out but Im struggling with the IPv6 support piece. The admin guides from Cisco seem to indicate that I'll need to configure IPv6 addressing on the ASA which makes sense, but doesnt fit my current design.
View 2 Replies
View Related
May 5, 2013
We use ISG on asr1000 (l3 routed subscriber). Now we are trying to implement ipv6 isg sessions. so.. for ipv4 sessions we have
radius-server attribute 8 include-in-access-req
radius-server attribute 32 include-in-access-req but for ipv6 there is no such attribute#radius-server attribute ?
11 Filter-Id attribute configuration
188 Num-In-Multilink attribute configuration
218 Address-Pool attribute
25 Class attribute
30 DNIS attribute
31 Calling Station ID
32 NAS-Identifier attribute
4 NAS IP address attribute
44 Acct-Session-Id attribute
55 Event-Timestamp attribute
6 Service-Type attribute
60 CHAP-Challenge attribute
61 NAS-Port-Type attribute configuration
66 Tunnel-Client-Endpoint attribute
67 Tunnel-Server-Endpoint attribute
69 Tunnel-Password attribute
77 Connect-Info attribute
8 Framed IP address attribute
95 NAS IPv6 address attribute
list List of Attribute Types
nas-port NAS-Port attribute configuration
nas-port-id Nas-Port-Id attribute configuration
what is best practice for authorize ipv6 l3 subscribers ?
View 3 Replies
View Related
Feb 23, 2010
I can't get IPv6 to work on my Cisco 877:Do I need to do something to enable it? I have a /56 from our ISP that I would need to configure.
View 12 Replies
View Related
Oct 25, 2011
how to enable ipv6 on pc?
View 1 Replies
View Related
Jun 15, 2013
I have a cheap VPS with 1 IPv4 and 5 IPv6.
I want to use 1 of the unused IPv6 connections on my computer so I can start using IPv6
View 1 Replies
View Related
Sep 9, 2012
I understand that IPv6 uses the MAC address of a LAN interface to make up the EUI-64 of a serial interface since serial interfaces don't have MACs. What happens when there is no LAN interface available? What if the switch has only serial interface cards?
View 2 Replies
View Related
Jan 9, 2013
i just came to know Assurance feature license doesn't come for free when upgrading from LMS4.2 or NCS1.1. It has to be purchased. Before buying this license, i would like to know if IPv6 netflow is supported.
View 0 Replies
View Related
May 7, 2011
I need to implement IPv6 for ASA VPN. According to the ASA_8.4_cli_cfg.pdf , IPv6 is not supported on ASA IPSEC vpn and remote client vpn. I do not have a ASA 8.4, any way to verify on ASA8.4 whether the crypto command support ipv6 address ? If the crypto command do support ipv6 address then probably there is chance it will work.what i mean is eg. crypto map xxx set peer <ipv6 address| ipv4 addres> able to set ipv6 address.
View 4 Replies
View Related
