I am attempting to upgrade my 1261n's to lightweight but the upgrade tool (3.4) is telling me that it is not compatible with this model AP. Is there an article or quick run down on what I need to do to upgrade these AP's?
View 2 RepliesI have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies View RelatedAm looking to upgrade the software on the ACE30 from: [code]. Any ACE30 guide that explains this. Have looked at the ACE30 configuration guide which I thought would cover this in the section "Managing The ACE Software", however everything else has been covered off except how to go about upgrading the software.
View 1 Replies View Relatedi am facing an error while upgrading the IOS image on 3560 switch. [code]
View 1 Replies View RelatedI just received a new 4510R+E switch with CAT4500e SUP7e Universal Image cat4500e-universal.spa03.01.01.sg.150-1.x01.bin software imag with License Level ipbase. We specified in the order to receive CAT4500e Universal Crypto Image with License Level ipbase. I have since requested and received the latest CAT4500e Univeral Crypto Image cat4500e-universalk9-spa.03.04.00.sg.151-2.sg.bin. Is there anything other that just installing the new image that must be done to allow me to use the Crypto Image? Would this upgrade do anything to change my License Level ipbase?
View 1 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedI'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies View RelatedI'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View RelatedI have some 1242s and I can't get a straight answer on whether they can do both autonomous and lightweight or just lightweight.
Model number: AIR-LAP1242AG-A-K9.
I'm assuming that the 'L' in the model numbers means it's just lightweight, but searching Cisco's site and the Internet in general it's just not clear.
I know it works as a lightweight AP, can I run it in autonomous mode?
My company uses a Sonicwall NSA 3500 as it's Firewall/WLAN controller and lightweight Sonicpoints for the private/public WIFI access. We are getting ready to implement wireless at one of our branch locations a few blocks away(We use Metro Ethernet to connect the 2).I know with the current firmware the Sonicpoints can't provision to the Sonicwall NSA over the Metro Ethernet like Cisco lightweight AP's can because the Metro Ethernet strips their VLAN Tags and obviously the Sonicpoints don't support REAP.what other options (short of installing another WLAN controller at the remote site) do I have to connect the AP's at the WLAN controller at our main location.
View 5 Replies View RelatedOur client have cisco 5500 Wireless lan controllers. They connect to core switch and other ports conenct to various switches on each floor. Then we have cisco AP 1300 series mounted on celing. I was reading that lightweight AP gets config from WLC as soon as they plug in. Need to know how the AP gets config from WLC switches?
View 8 Replies View RelatedI have a air-lap1042-n-e-k9, how to put this wi-fi mode autonomous ?
View 5 Replies View Relateda few day l have 3 AP Ligthweight 1250, today l was checking my infrastructure and l saw that these 3 AP can´t join to the controller, l reset the AP to the, and its can not join, l checked physicly the AP, and the Ethernet Led is in Amber permanent and the Radio Led is in Green permanet , i am searching the status led to find the fix but l have not found these convination led. and l can not access to the consolo port.
View 2 Replies View Relatedhow to convert a 3502 access point from Autonomous to Lightweight ? 3502 has a new IOS released back in Dec 2012 to work as staandalone mode. I need to convert this back to Lightweight mode.
I have been searching on web but have had no luck so far with anything. Tried converting it to lightweight in the same way as putting it on Autonomous IOS but errored out.
how to convert a 1602i AP from lightweight mode to autonomous?
View 3 Replies View RelatedI have a problem converting 2602 from lightweight to autonomous. It will not boot to the autonomous IOS. The procedure below is waht I did.
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init
[Code].....
How can I upgrade my 1041N AP to lightweight firmware? I found an upgrade tool which works in only XP and 2000 machines. I do not have these outdated OS so is there another way to upgrade it to lightweight?
View 2 Replies View RelatedHere is what I am attempting to do.
1. I have a 1042N AP configured as a Workgroup-Bridge attaching to a Lightweight Access Point.
2. LWAPP AP is on a 5508 series Controller.
3. I have MAC Authentication configured through an Ciso ACS box running 5.2 code. And that portion is working.
4. I want to lock this WGB down even further with a second layer of security. I am thinking WPA2 -AES.
I cannot TFTP this tar file to both 1230 and 1231 APs. Both are lightweight APs that I've wiped to the rommon mode (ap>) and I issue the command:
tar -xtract c1200/k9w7-mx.123-8.JA 10.0.0.2
And I get a error saying: "permission denied"
Notes:
The AP has defaulted to the 10.0.0.1 IP.
My laptop is set to 10.0.0.2 255.255.255.0 IP
My TFTP-Server is on and the root folder with the .tar file is in there.
ether_init, flash_init, tftp_init (these commands have been executed)
My firewall is disabled.
I keep getting the following error "Could not execute JDBC batch update" when trying to add AP to WCS ... other 1240 APs added without any problems.
View 4 Replies View RelatedWe have a couple of smaller remote locations running cisco 1811W routers (built in switch ports & wireless).Now I have been tasked with determining if the wireless portion can be converted to Lightweight or not; if so what is required.
I am running
WCS 7.0.230.0
WLC 5508 (same code)
How to upgrade C3502i to Lightweight? I failed to upgrade using Upgrade tool v3.4. The error message is "AP model is not supported" . how can I upgrade it?
View 9 Replies View RelatedIs it possible to manage Lightweight Access Points in Ciscoworks LMS 4.0?
View 3 Replies View RelatedIs there any difference between AIR-SAP2602-x-K9 with lightweight IOS and AIR-CAP2602-x-K9?
View 3 Replies View RelatedIs it possible to convert an Autonomous AP 2602i to Lightweight just changing firmware as the first generation Aironet APs?
View 2 Replies View RelatedApparently converting autonomous 1142N to lightweight is not supported by ether WCS 7.0 or the Upgrade tool. The option is to do it manually with CLI, but there is about 200+ AP's that need converting. We can't do them all at the same time. We have to do it building per building.
View 4 Replies View RelatedDoing the firmware upgrade on a 1041n AP from Autonomous to Lightweight. Downloaded from Cisco, checked MD5 and got a match so went and upgraded. Upgrade went find etc.. and rebooted. When I reboot I get the following error and then rubbish text
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x0000018a
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
[code]...
I rolled back to the autonomous OS and all ok and AP operates as normal. When on the lightweight IOS I can get a telnet response but cannot access as it states Password require but not set.
Followed this process to upgrade [URL] and followed this process to restore to Autonomous: [URL] why it's not working.
Update: Just tried another AP same result. Downloaded Lightweight again and same result
Here is the CLI upgrade process
examining image...
Loading c1140-rcvk9w8-tar.124-21a.JA2.tar .from 172.16.4.114 (via BVI1): !
extracting info (273 bytes)
Image info:
Version Suffix: rcvk9w8-
Image Name: c1140-rcvk9w8-mx
[code]....
Is AP 1220B (b-only radio) supported for registration to WLC (7.0.x) with Lightweight software? I've managed to convert the AP to Lightweight mode, but I could not get it to register with WLC 2504 (software version 7.0). Is it possible that this AP is only supported if changing the in-built radio module?
In the compatibility matrix [URL] there is an information that this AP is supported on WLC up to version 7.0.x. On the other hand it is not supported by Autonomous to Lightweight Mode Upgrade Tool [URL] Since these APs does not have pre-installed MIC, it is mandatory for them to create Self-Signed Certificate (SSC). Upgrade tool could do this job (along with adding the created SSC hash to the authorized list on WLC), but it does not support this particular AP/radio. If I do the conversion manually (archive download-sw ...), the AP does not have the SSC needed for communication with WLC. I've tried making the SSC manually (instructions found on this site [URL] while AP is autonomous mode, and then converting it to Lightweight, but the AP still could not register to WLC.
In the debugs (on WLC/AP), I am receiving an error that is described in some Cisco troubleshooting documents as something related to WLC not having an SSC hash in the auth list. Problem is that the AP is not even sending standard CAPWAP messages and there is nothing to be seen in "debug pm pki enable" on WLC...
I have several Lightweight APs (AIR-LAP1242G-A-K9) runing of a single WLC. We keep getting devices, sometimes all devices, losing network signal. The WLC is running a global power setup so all APs have their power set automatically. The setting for power parameters are default. I have noticed when I run a client test the APs run at 11Mbps while the client devices run at 50-54Mbps. The protocol used by both devices is 802.1G. These network drop offs are frequent and I should say may well be an issue with the client devices although there are several different types of devices experiencing this issue. My question is should the TX and RX rates be the same? Is it ok to have this disparity in the TX/Rx values?
View 7 Replies View RelatedSome of my Lightweight Access Points lose connection every 10 minutes now, it worked without problems before.
I'm using an AIR-CT5508-K9 Controller with Version 7.0.116.0 and AP are all AIR-LAP1242AG-E-K9.
In the log I find informations about my node changing his parent and then reseting the radio interface.
I checked my configuration, but perhaps I missed something.
7Mon Oct 31 14:35:11 2011AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:00:3a:99:90:55:c0 Cause=Radio interface reset. Status:NA8Mon Oct 31 14:35:11 2011AP's Interface:0(802.11b) Operation State Down: Base Radio
[Code]......
is there any issue in buying air-ap1142n-ek9 802.11A/G/N FIXED AUTO AP INT ANT and later on converting it into lightweight under the control of air-ct2504-15k9 2504 WIRELESS CONTROLLER WITH 15 AP LICENSES ?Are there any requirements on the SW of the WLC and the IOS of the AP? The reason of the choice is budget.
View 1 Replies View RelatedIs possible to configure a Lightweight Access Point LAP1242AG as 802.1x supplicant using Microsoft NPS radius server that not use EAP-FAST authentication method? Can I use PEAP in NPS radius?
View 6 Replies View RelatedThis is one of our first site where we are implementing Cisco wireless, and we bought some external Autonomous AP1262, when we should have bought Lightweight LAP1262 . We can get those replaced, but I am looking into migrating them in order to get them to register with our 5508 controllers.
There do not seem to be a migration tool to download for 1262. Must it be done via the WCS ?So far I have not managed to add these autonomous AP to the controllers. How to know if a migration toll exists for those !