Cisco WAN :: 2811 Run Bgp With ISP To Accept Just Default Route
Feb 18, 2012i have 2811 router can, i use the below image on it , i m thinking to run bgp with ISP to accept just default route.
View 1 Replies
ADVERTISEMENT
Cisco WAN :: 2811 EBGP With Static Default Route
May 8, 2011My 2811 is connected with two ISP,s as below and have VPN with Central branch.I want to set DSL as primary and WiMax as secondary but problem is that routes learned via BGP get precedence over default route as they are specific one.I think i may need to put all static specific routes of central branch over DSL along defautl but I want any idea if my default route stay active and when it down then BGP neighborship can be establish (like ip sla tracking.)
View 3 Replies View RelatedCisco VPN :: Get 2811 To Accept Two IPSec Peers?
Dec 12, 2011I am trying to get a 2811 to accept two IPSec peers however can only get one working at a time. I have setup fa0/0 and fa0/1 with their own public facing IP addresses with crypto maps associated to each interface however can only establish connectivity to one interface at any one time.
Relevent configuration below:
crypto isakmp policy 2
encr 3des
hash md5
authentication pre-share
group 2
lifetime 28800
[code]....
Cisco Firewall :: 5510 Trace-route / Antispoofing On Not Default Route
Jun 24, 2011I've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
Cisco Switching/Routing :: PBR - 3750 VLan Does Not Accept IP Policy Route-map
Nov 1, 2012I am trying to configure policy based routing however when i try to apply to an interface vlan. The configuration does not show in the interface.
route-map OTHER_ROUTE permit 10
match ip address OTHER_ROUTE
set ip next-hop x.x.x.x
[Code]....
Cisco WAN :: 2811 - Route Over Mpls Link?
Mar 2, 2012i have 2 routers 2811 interconnected together ,1 of these router running in circuit with 2 Mbps over Internet the 2nd one use MPLS Circuit with a bandwidth of 4Mbps,how configure the routing to route over the MPLS while IPSec act as standby
View 1 Replies View RelatedCisco WAN :: 2811/ 3845 - OSPF Route Update
Feb 6, 2011I m using ospf between HO and Branches for two links. branch router are 2811 and HO router 3845. when i enable ospf at branch i get all branch route like HO router and a default route. My requirement is each branch get only HO but no other branch. I have no default route.
I attached show ip route status for a branch router.. Why default route comes and why all branch's route come ?
Cisco WAN :: 2811 Dynamic Route For High Latency
Apr 4, 2012I have cisco 2811 at branch and 3845 at Head office. Two link with 256 kbps bandwidthe each. I did as follows: [code]
When link 1 down, traffic change to Tunnel 2. its OK.I want when link1 flaxuate or latency high (more than 60 ms) traffice change to tunnel 2. If link 2 goes high latency automatically change to tunnel 1.
Cisco WAN :: Configure Policy Based Route On 2811 Router?
Jan 19, 2013configuring policy based route for my cisco router?Basically, I have a 2811 cisco router with 2 ADSL ports. 1 port is for iiNet line and another port is for Telstra line.I want to configure a policy based route on the router so that:Any traffic coming from 1 internal IP (i.e. 172.16.x.1) will go through iinet line (i.e. Dialer 0) interface.Any traffic from rest of the office will go through the Telstra line (i.e. Dialer 1) interface. Is there any easy way to configure this policy based route?
View 8 Replies View RelatedCisco :: Leak Default Route To VRF?
Jul 1, 2012I want to leak default internet route to CE VRF as common service.Since we having two ASBR, can I point next hop to PE itself instead of either of the ASBR?I tried to point NH to loopback of the PE itself but it failed.
View 6 Replies View RelatedCisco WAN :: BGP 300 - Default Route Maps
Sep 3, 2011I'm working on a practice lab and am having the following issue. I have a customer router connected to two different ISP routers. Each ISP router must advertise a default through BGP to the customer and one of the default routes must be preferred over the other. Given if the preferred route interface is shut down the other default route is inserted into the routing table and when the preferred default route interface it turned back on that path is used again. The catch is I cant alter the customer router only the the two ISP devices. I tried doing some route maps but I'm lost. I have deleted all my route maps and have posted the BGP portion of the ISP routers.
router bgp 300
no synchronization
bgp log-neighbor-changes
[Code]....
Cisco Wireless :: 2811 - Can't Ping Default Gateway
Jun 9, 2012I'm trying to get a 2811 router with a NM-AIR-WLC6 Wireless Controller Module to work with an c1200 series access point. The LWAP is connected to a 2690 switch which has a trunk connected to the router. My configuration looks very similar to example 2 on this page: [URL] . The LWAP does get an IP from the DHCP pool on the router. I can also connect to the GUI of the controller from a PC on VLAN 250 (which also is connected to the switch).
[URL]
The moment I join my Wireless network I get no IP and when I enter a valid static IP, I still can't ping the gateway. I also noticed that the controller could ping the gateway before I configured the interface. After configuring an interface with that gateway, the controller loses the ability to ping to it. I can't seem to figure out why. I've been working all week on getting this controller and LWAP to broadcast a fully working network.
Cisco :: OSPF NSSA Default Route?
Jan 19, 2013Looking through the SPROUTE course material they state on several occasions that an ABR will announce a default route in to a standard NSSA area, same as a stub area, because LSA5 external routes are not allowed.
View 8 Replies View RelatedCisco Firewall :: ASA5510 / Default Route With Different AD Value?
Nov 14, 2011Will ASA5510 support default route failover mechanism by giving two different AD value in the route outside command?
View 1 Replies View RelatedCisco Routers :: WRVS4400N Default Route
Feb 26, 2013I bought a WRVS400N v2 to be used as an access point. Currently it is hooked up on my switch via a trunk port and is able to communicate with my gateway. Whenever I try to access an IP subnet other then the local IP address of the WRVS, I get a network unreachable error. To fix this for my local networks, I added the appropriate static route to cover my local LANs and that seems to work now. I tried to add route 0.0.0.0/0.0.0.0 using the web interface for internet access, but somehow it does not recognize this as a default route (quad zero!?). Does any know how I can set the default gateway in this router? Maybe, but hopefully not, I have to use the WAN port to create some kind of uplink and use one of the LAN ports to connect using the trunk port and route traffic for the clients over the WAN port .
View 1 Replies View RelatedCisco WAN :: 877 Default Route Using Track Command?
Jun 5, 2013I have an 877 router which has a DSL WAN interface. The DSL service at this site is unreliable, so the company have purchased a separate 3G router to be used as a backup. This device maintains 3G connectivity at all times and has a static IP on the internal subnet (for arguments sake let's say 10.0.0.253).
What I want to do with the Cisco router is to track the DSL interface and if it is up, install a default route pointing to it. If it is down, I want the default route to be the 3G router.
I am thinking the best way to do this is to set up a track and then set 2 default routes; one which is installed if the tracking is up, the other has a higher admin distance and points to the 3G router and thus should only be used if the track is down. For example:
track 10 interface Dialer0 ip routing
delay down 30 up 30
ip route 0.0.0.0 0.0.0.0 Dialer0 track 10
ip route 0.0.0.0 0.0.0.0 10.0.0.253 100
Is this likely to work or is there a better way to do it?
Cisco Routers :: SRP521W - Default Route Through VPN?
Mar 18, 2012Is it possible to send all traffic through site to site VPN using SRP521W (on the other site ASA) ? Lets say, traffic to Internet from branch through HQ - site to site VPN between branch and HQ. I've tried to set up destination crypto policy entry to 0.0.0.0 0.0.0.0 but it's not accepted. Firmware version is 1.01.26 (003)
View 4 Replies View RelatedCisco WAN :: ASA 5510 - NAT / Default Route To Two ISPs
Nov 14, 2011I am having a strange requirement. actually I am not sure it is strange or not. I am having ASA5510 with 8.4 sw version. Currently one ISP is connected to it. It is working fine. We have some servers that are directly connected to internet using another ISP connection. These servers having public IP addresses configured on their LAN settings. I need to move these servers in to the DMZ zone.
When i connect it to the ASA's DMZ zone,servers will get internet through the first ISP that is already configured on ASA. But i need to NAT the DMZ servers with the IP address provided by the other ISP, which even not configured on ASA.
So what should i do? In short my requirement is
1) need to NAT the server with the IP address provided by another ISP
2) Also note that the default route is configured for the first ISP only in ASA
so Do i need to configure another default route? Do i need to make it with larger AD? So i do it will act as the secondary route only.
I need to make the ASA up and running for two ISP, and servers in the LAN should be able to NAT with the IPs of first ISP and ,the servers in the DMZ zone should be able to NAT with the public IP of the new ISP.
Cisco WAN :: Does IP Default-gateway Have Any Effect On L3 Device Such As 2811 Router
May 21, 2013Does ip default-gateway have any effect on a L3 device such as a 2811 router? I always thought that on a L3 device the default route would supersede any such command assuming it is accepted.
We have a client device that cannot be reached for managment directly and wanted to add that statment only if it might work.
Cisco :: Default Route And More Specific In Case Of IP Transit
Aug 16, 2012In case customers buy IP transit(there is a BGP session between ISP and customer), they often ask for default route and for example prefixes from local internet-exchanges. What is the advantage to have default route + certain smaller(for example /17, /18 and /24) prefixes?
View 4 Replies View RelatedCisco :: Select A Default Route Within MPLS/VPN Network
Nov 30, 2012I have this topology: ( I use OSPF instead of EIGRP for routing between PE CE. The customer vrf name is cusA, they have 4 sites: CE from site 3 have 2 links to 2 PE ( one for backup). CE from site 3 has exist point to internet and how can i choice 1.1.1.2 is next-hop for default-route
View 2 Replies View RelatedCisco Firewall :: 871 / 2811 / 1841 - ZBFW Default Inspection Specification
May 6, 2011I can't find any specific information on the implementation of packet inspection in a zone based policy firewall. In other words, is there a specification or even just a set of values that define the default inspection parameters for all protocols? With DPI I can manage 'some' of the inspection capabilities but I have some fairly rigorous and specific requirements to meet and I need to validate that the IOS ZBFW will meet those requirements. Specifically, I'm interested in HTTP, DNS, and ICMP but all other protocols would be useful as well.I'm working with basic routers; 871's, 2811's, 1841's, etc. The IOS in use in most cases is adventerprisek9-mz.151-3.T.
View 4 Replies View RelatedCisco Switching/Routing :: 2811 / BGP / Default Originate Timer At Max Delay Of 64 Sec
Jul 22, 2009I have a working BGP session established. With "debug ip bgp events" I see many (2/3 every second) messages like this:
*Jul 23 11:23:48.773: BGP: default originate timer at max delay of 64 sec
*Jul 23 11:23:48.997: BGP: default originate timer at max delay of 64 sec
I can find nothing about this message. IOS version is 12.4(24)T and platform is Cisco 2811
Cisco Switching/Routing :: 7206 - PBR Not Changing Default Route
Sep 5, 2012I have a MPLS cloud in our data center. I want one network coming into our core router to have a different default route than the other networks coming in. I'm getting hits on the acl but the route isn't applied and goes to the default route that is configured in the router. I have other PBR for setting local-preferences and as-paths and they are working fine.
The router is a 7206 Version 12.4(11)T3
!
ip route 0.0.0.0 0.0.0.0 1.2.3.4
!
ip access-list extended 2nd_Default_Route
[Code].....
Cisco Switching/Routing :: 2960 Default Gateway Ip Route
Jan 24, 2013I have a Cisco 2960 ( WS-C2960-8TC-S) running 12.2(46)SE C2960-LANLITEK9-M image.I would like to set an ip route 0.0.0.0 0.0.0.0 87.101.156.97 but the current image does not allow.Will ip default-gateway 87.101.156.97 work or do I need ip routing ?The ISP has provided a /30 address and we are using an additional /29 for our network devices. I dont think this image can be upgraded. I need to forward routes directly out to ISP. [code]
View 5 Replies View RelatedCisco WAN :: IP SLA And Object Tracking For Default Route On Nexus 7010
Mar 18, 2013We have a Nexus 7010 running version 6.1(2).
I'd like to use IP SLAs and object tracking to define static routes for specific source/destination traffic across some WAN links we have. I've done this in IOS and it's worked fantastically, but I've not found where/how to do this on the Nexus 7010 platform (or any Nexus platform) as of yet. I could have sworn that this was going to be introduced in the 6.x code? Below is an example of how we do this in the IOS world:
track 11 ip sla 1 reachability
delay down 15 up 15
ip sla 1
[Code]....
Esentially this gives us the option of using a "failover" default route. I've attached a basic diagram to explain what we are trying to do with IP SLAs and object checking. The tracking should be configured against an SLA that uses icmp and the static routes should be configured against the tracking.
Cisco Switching/Routing :: IP SLA On 3750 Default Route Failover
Jul 27, 2010IP SLA configuration fails over but cannot ping the 4.2.2.2 via Site B. Here is the output on Cisco 3750...
SW2#show runBuilding configuration...
Current configuration : 2901 bytes!version 12.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname SW2!boot-start-markerboot-end-marker!!!!no aaa
[Code].....
Cisco Switching/Routing :: 3550 OSPF Default Route
Aug 19, 2012I'm working on a little OSPF setup in my lab and having a problem pinging out to the internet.I have a setup with (3) 3550's running ip routing. I'm configuring OSPF but I can't ping the internet from any L3 switch except the switch with the actual uplink to the internet.[code] From SW2 and SW3, I can ping SW1 on all IPs (192.168.1.90, 10.10.10.1, 10.10.10.5) but I can't ping 192.168.1.1 which is my gateway to the internet.
View 3 Replies View RelatedCisco WAN :: 7200VXR - BGP Advertising Default Route In Mutihomed Network
Feb 25, 2011I have Cisco 7200vxr doing BGP with 2 directly connected ISP's over ethernet. I am receiving default routes only, and have added a higher weight to my routes learned from my primary ISP. below is my configuration (ip addresses changed of course)
router bgp 100 no synchronization bgp router-id x.x.x.x bgp log-neighbor-changes network 100.100.64.0 mask 255.255.254.0 network 100.100.71.0 network 100.100.78.0 mask 255.255.254.0
neighbor <ISP_A-IP> remote-as 200 neighbor <ISP_A-IP> weight 175 neighbor <ISP_B-IP> remote-as 300 neighbor <ISP_B-IP> weight 150 auto-summary
Advertising my rotues to the primary ISP is fine
7206vxr.rb#sh ip bgp neighbors <ISP_A-IP> advertised-routesBGP table version is 7, local router ID is x.x.x.xStatus codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S StaleOrigin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path*> 100.100.64.0/23 0.0.0.0 0 32768 i*> 100.100.71.0 100.100.64.57 0 32768 i*> 100.100.78.0 0.0.0.0 0 32768 i
Total number of prefixes 3
However, advertisements to the secondary ISP inlcludes the defautl route learned from the primary 7206vxr.rb#sh ip bgp neighbors <ISP_B-IP> advertised-routes BGP table version is 7, local router ID is x.x.x.x Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 0.0.0.0 <ISP_A-IP> *> 100.100.64.0/23 0.0.0.0 0 32768 i*> 100.100.71.0 100.100.64.57 0 32768 i*> 100.100.78.0 0.0.0.0 0 32768 i
Should I not just only be advertising just the networks that i specified in my configuration?
Cisco Switching/Routing :: EIGRP Default Route 3750
Jun 20, 2012I have a 3750 at a branch running EIGRP connected to two routers that both have configured:
access-list 1 deny 0.0.0.0
access-list 1 permit any
access-list 2 permit 0.0.0.0
access-list 2 deny any
router eigrp 1distribute-list 1 out FastEthernet0/0distribute-list 2 in FastEthernet0/0
Due to this recently applied config the switch become unreachable from the outside and cannot ping anything. Everything connected to it works fine. I was able to remote into it from a switch behind it and noticed that the 3750 has no default route in the routing table. I do see a default route in the eigrp topology table. How to make the switch learn a default route maintaining the existing configuration on the routers.
Cisco Application :: Failover ACE / Default Route Redundancy / 6500
Jun 20, 2011Since the ACE supports only static routing, when pointing a default route from the ACE what is your preferred method when using multiple 6500s with an ACE in each in a failover scenario to prevent just pointing at one 6500? Static route to an HSRP address? Multiple static routes on the ACE, etc?
View 2 Replies View RelatedCisco WAN :: 4507 - Preferred Default Route Over Another Based On Source IP
Jan 21, 20132 ISP's connected to a 4507, both with seperate public IP blocks. Based on some source IP addresses on the LAN they would either use ISP-A or ISB-B's connection based on what I define.
View 3 Replies View RelatedD-Link DIR-615 :: How To Route All Incoming Connections To Default To Web Server
Jan 3, 2013How to configure my DIR-615 (Hardware Version E1 - Firmware Version 5.00NA) to:
1. Assign/Reserve IP address for 2 machines.
2. Route a web browser to a server on the first machine (port 80) as a default when another computer or smart-phone or device joins my open wireless network.
I am hoping to eliminate any changes to the IP address of the first two computers so that the server's IP address and port are static. I would also like anyone who joins the network to merely open their browser and be presented with the http interface from my server.