I doubted my internet ADSL is very weak. I used Cisco 877 router to gateway internet.I faced the problem my cisco 877 can't receive signal from ISP but I replaced to use Linksys Cisco. It worked.So I remoted to router and issued command show dsl interface atm 0 it can't generate DMT bit per bin it showed error.
View 5 RepliesI have a Verizon Actiontec router without N band. I cannot receive the signal in the farthest corner of my home. Apparently using an N band router will solve this problem with the higher output. Verizon refuses to send me a new router with N band, stating that they will merely send me a replacement for the current router w/o N band. Therefore I want to change this router out. I don't know if the Actiontec has a built-in modem, and if so, how and what can I use as a replacement router.
View 4 Replies View RelatedI received three things for Christmas: 1. Linksys WiFi E1200, 2. Pandigital Planet tablet, 3. Roku.My family room is on the same level as my Wifi router but about 70 feet apart, but I cannot get a wifi signal in the family room on the Pandigital tablet, however, the Roku seems to be receiving the wifi signal because the Roku works.Is my tablet not working correctly? Can and should my son increase the signal strength of the Linksys
View 5 Replies View RelatedI need a router that can receive the signal from my Verizon 4G Jetpack so that I can send signal to items that require cat5 cable.Can the WES610N do that or is there one that can?
View 1 Replies View RelatedFor the past 2 days I have been having a problem with my laptop taht, actually a bit old. I also have another pc, a desktop, with a d-link modem and wireless router (DIR-615). The problem is that I can't go on the internet with my laptop, because of a certrain error on the Intel PROSet Troubleshoot: "Did not receive IP addresss", in fact the IP address was written as 0.0.0.0, and when I open the internet browser I can't go on to any page. IO have tried everything, believe me, from switching off every thing, to reinstalling the router, but nothing seems to resolve the error.
View 12 Replies View Relatedi use my sim card in modem connected to pc to surf. is it possible to receive calls as i surf through this sim card?
View 1 Replies View RelatedI've got an ASUS G50V that I normally connect to the net through a wireless router but I recently bought a router so I can make a physical connection and increase speed. However I cant get it to connect to the router no matter what I do (i had it working for a few hours at one point but it dropped off again).I confirmed it wasnt the router but running a crossover cable from the laptop to my desktop, setting static ips on both. Now I can ping the laptop from my desktop but for some reason I cannot ping the desktop from the lappy. I've tried everything I can think of but no dice.
View 4 Replies View RelatedI'm a beginner on networking, and now i've found a problem while i do an exercise.i have one pc connected at one allied telesys but the last one is a trasparent bridge...the AT is connected whit a fortigate the fortigate does nat..and is connected whit the modem.i can go on server, modem receive ping from pc..is everything right..settings.
View 1 Replies View RelatedI have an old Buffalo router which im trying to connect to a virgin media modemProblem is the router doesn't have a direct Ethernet port for internet, only ADSL.What I thought I could do was connect using one of the LAN ports and make my router think it was receiving internet through a network? Is this possible and how can I do it?
View 6 Replies View Relatedican receive e-mail, but I cannot send it.
View 1 Replies View RelatedI have connected the computer to the internet a multitude of ways, and no matter how i do it, it always can not receive packets. It is sending packets though.I have tried connecting it directly to the modem, with different wires, through a router, through a network card... I'm pretty much at a loss, im not an expert by any means but im not computer illiterate either. Chances are this is a simple fix... My other computer (the one im on) works fine with both cords, connected directly, and through the router to the modem.
View 2 Replies View Relatedis it possible to receive a fax via moblie phone?
View 1 Replies View RelatedI can receive but not send faxes. When I try to send an operator comes on and says please enter the number you are trying to reach. I plugged in another machine and it does the same thing.
View 2 Replies View Relatedcisco 2811 - DHCP server..If IP Phone 3905 installed in SF 300 he does not receive an ip address. [code] If IP Phone 3905 installed in the Catalyst 2960 - all OK.
View 7 Replies View RelatedThough other logs are being received through the email.
View 1 Replies View RelatedI want to receive full BGP in my switch 6506 with the follow characteristics: cisco WS-C6506-E (R7000) processor (revision 1.2) with 458720K/65536K bytes of memory and Supervisor Engine 720.When I configure the session BGP in my router with me peer the switch begins to work slow and restarts.
View 2 Replies View RelatedWe have problem con EIGRP and two ASR 1001 in High Availability. ASR2 have received all route (100 route) from PE, but in ASR1 doesnt received all route (75 route) from PE or from other ASR02. All PE have all route. The ASR1 when modify or lost some route dont update to the ASA. see diagram.
View 5 Replies View RelatedI'm trying to configure Cisco CISCO881G-K9 3G router to connect to mobile network without success. The cellular interface gets up but it doesn't receive IP address. It seems that profile isn't activated and it should've been.
I've attached running config and some other information gathered from router.
I have setup about 16 devices to syslog to LMS4.1 Vmware eval... but I am not recieving any messages at all. I know these devices are generating syslogs to another system but lms doesn't show anything under monitoring / syslog_info.
Is there anything special I need to do to setup LMS4.1 to receive syslog's sent directly to its IP. .e.g. not using an external syslog server but using LMS.
I've got clients using the Cisco VPN Client (version 5.0.07.0290), and an ASA 5520 set up as the endpoint. 99% of the time this works great, so I'm pretty confident with the config, but there is one specific user who is having a problem (although sometimes it works ok for him). This user is connecting to the internet through a 3G dongle, and then trying to VPN in. I can see the connection being established, RADIUS authenticating his credentials, and the tunnel being set up without issue.
No data seems to pass through the tunnel however. Lots of packets are sent, but none are ever received back. Looking at the VPN statistics on the client, I can see that Transparent Tunneling is inactive, so I'm presuming I've got a NAT issue somewhere. The output of sh vpn-sessiondb remote seems to confirm this (user 1 is the problem user, user 2 works fine):
Username : user1 Index : 1332
Assigned IP : 172.17.47.191 Public IP : xxxx
Protocol : IKE IPsec
License : IPsec
Encryption : AES128 AES256 Hashing : SHA1
Bytes Tx : 0 Bytes Rx : 0
Group Policy : Tunnel-Group-1
Tunnel Group : Tunnel-Group-1
Login Time : 06:18:57 UTC Tue Nov 22 2011
Duration : 0h:14m:41s
Inactivity : 0h:00m:00s
NAC Result : Unknown
VLAN Mapping : N/A VLAN : none
As you can see, for the problem user, just plain IKE IPSec is negotiated, without NAT-T.
Can't receive emails from specific emails. This happened after a Windows update in December ,A and did not correct after the update on Jan .B, 2012
View 2 Replies View RelatedMail in yahoo alwaysworked until recent Sunday . Now can receive email but not send in yahoo Yet a sent copy is saved in my sent box. but my recepients do not get the mail
View 1 Replies View Relatedcannot read and receive emails
View 1 Replies View RelatedCan receive email but cannot connect to the Internet, my user can get to all shared files on the network and get emails through exchange but cannot browse the internetWe turned off the firewall and checked DNS and the IP. It says the local area connection is connected. We added IE to the exceptions tab in firewall.
View 1 Replies View RelatedI recently migrated keeping my original email address. All went well, except I am unable to receive emails from one of my contacts. I can send to this individual successfully, but when the contact tries to respond the reply kicks back to him telling him that there was a delivery notice failure. Email addresses have been verified by both of us and both are accurate
View 2 Replies View RelatedI have problems in the following scenario. I attached an image with a summary diagram of the network in question. The problem is that on the 3rd floor of the site users connect via wireless fail to connect and receive an IP. But they can not navigate. The second and first floor itself. As you see in the diagram are 3 routers, one per floor. The first is the only router that provides DHCP the other two routers are as simple Access Points.
View 13 Replies View RelatedAt random times, my internet will "drop" connection and will not download any packets, but I am still able to send packets. My Local Area Connection icon continues to say I am connected, my modem is fully functional, and my cables are good. I can get my internet back up and running for 10 minutes or so by disable and re-enabling my Network Connection. If I simply try the "repair", it gives me an error at the "Refreshing IP" step.I have done a full system scan for viruses and I am clean. My drivers are fully updated, I have disabled my firewalls, and still no luck. During the times when it is down, I can successfully ping my modem through CMD, but I get the time-out error if I ping a site, my default gateway, the DHCP Server, or the DMS Servers.I have made no changes to any major settings on my computer, nor has there been any recent additions/removals of any software.
View 7 Replies View Relatedi did just had a rogue anti-virus infection i did a removal of it AV Security 2012
View 1 Replies View RelatedAlright, so we have about six computers on average all on at the same time, working just fine, last night one of the laptops just, stopped working, saying there is no internet access, With every attempt it doesn't send any information. When I disconnect it from the wireless, then reconnect it, it immediately receives packets but won't send any.
View 1 Replies View RelatedI have the latest Firmware version 2.05NA on the DIR-825 and while I can make outbound SIP calls I can't receive any inbound calls. The phone will ring but I can't pick-up the call. [code] I am at a loss as to how to register my phone. When I uncheck ALG SIP the phone will not register to my server.I have a Polycom 550 connected to a Trixbox server. The prior router worked great.
View 6 Replies View RelatedHow can I receive log file from cisco 7609?
View 2 Replies View Relatedon a Cisco 4900M running IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICESK9-M), Version 15.0(2)SG1, RELEASE SOFTWARE (fc4) I'm getting a lot of packets on CPU Q "L3 Glean, 6".What is that queue and what could be the root cause?
Packets Received by Packet Queue
Queue Total 5 sec avg 1 min avg 5 min avg 1 hour avg
---------------------- --------------- --------- --------- --------- ----------
Host Learning 1563 0 0 0 0
L2 Control 1138188 3 0 0 0
Ttl Expired 2 0 0 0 0
L3 Glean, 6 4889394 4067 4381 3367 779
[code]....
my college using WisM (WS-SVC-WISM-1-K9) as wireless controller , Cisco 1130 access point and Cisco Secure ACS 4.X Solution Engine 1113 Appliance as radius server. For username and password, we take it from existing Oracle database.
The problem is the password that store in oracle database is in encrypted format. Base from feedback from database administrator, the encrpytion is done by oracle - application layer and cannot be decrypt back.
To tackle this problem, we decide to use external script in php to verify the username & password...The php script will check directly from oracle database. If the username & password match, it will sent a boolean true (1) to the Wism controller and if the username & password not match, the script will send boolean false(0) to the Wism controller.
My question is, can WiSM module talk to php script? Can it receive boolean parameter from php script?