Cisco WAN :: 881 PPPOE Won't Authenticate Against Mikrotik Router
Mar 5, 2013
Summary of setup Internal Network --------Cisco 881-(PPPOE)------------------------(CHAP)---ISP Mikrotik Router -----------internet
Basically it was working then there was a power outage and now it wont authenticate against the Mikrotik router. Strange thing is CHAP seams happy with the username and password. Then just terminates the connection.I've also tried PAP but not joy. Nothing appears to have changed. I have access to the Mikrotik and it looks the same as before also.
interface Dialer1
description Internet
bandwidth 7500
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
[code]....
View 6 Replies
ADVERTISEMENT
Nov 20, 2012
We have a Cisco 1522 ap bridge running on a controller and we want to create a wireless bridge from the Cisco AP to a Mikrotik SXT5HPND wireless router to a cisco 2960s switch
How to bridge a cisco device with a mikrotik device, but there are plenty who do mikrotik to mikrotik bridging..
View 3 Replies
View Related
May 24, 2012
I have been looking for a new router that can handle intensive bandwidth for my office which can handle vlans, QoS, bandwidth management, VPN/VPN Passthrough, and perhaps multi-WAN/Load Balance. A friend has recommended the Mikrotik RB 1200 for my application, having looked at the product the feature set seems to be quite extensive and the price point is very attractive. The router is also rack mountable (a big plus!!!), my question is wether the router is relatively easy to configure/manage. I have managed/installed other routers such as the Cisco SMB series but I have no experience with Mikrotik. I am very tech savvy and have a moderate knowledge of network infrastructure. I have heard so may different responses to the simplicity and I would like y'all to weigh in before I purchase the router. (OR WHATEVER RACKMOUNTABLE ROUTERS YOU RECOMMEND FOR SMB)
View 10 Replies
View Related
Jun 19, 2012
PPPoE is established and I can access router from outside. But router can't ping itself and ouside and NAT isn't working as well. Main goal is to make Internet work from router.
Cisco IOS Software, C890 Software (C890-UNIVERSALK9-M), Version 15.0(1)M7, RELEASE SOFTWARE (fc2)
version 15.0
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
[Code].....
View 2 Replies
View Related
Jan 2, 2013
I just switched to DSL from cable internet and am having some trouble setting up my router with the new internet service. DSL modem-->Router-->Network with PC and PS3
ISP is ATT
DSL modem is a TP-Link 8616
Router is a D-Link DIR-628
I put my ATT username and password into the router but it never completes a connection to the internet. I was able to create a soft PPPoE gateway connection through my computer using my username and password, but I want my router to do this, not my PC. How do I get my router to connect directly to the Internet connection rather than having my PC connect? My setup would be fine as-is if I just had 1 computer but I also want to go online with my PS3, and it won't connect like my PC will, even after putting the username/password in.
View 11 Replies
View Related
Jan 7, 2011
A PC connected to a Cisco 877 router and 877 router is connected to another router (7301) via GRE tunnel,Cisco 7301 router is a NAS server and is being used as a PPPOE server.If user create a PPPOE connection on his computer and dial with a username/pass we want to send the PPPOE traffic to 7301 router, so 877 router should pass the PPPOE traffic to 7301 and user will be able to connect,User -> 877 -> 7301(PPPOE server).
View 4 Replies
View Related
May 13, 2013
I get stuck in one case. One of my customer has two FTTH lines. I have to config PPPoE in routers. In one line I config succesfully, but one line never up. I call to ISP they ask me to config extactly VLAN id 10 in the physical subinterface. But in subinterface there is no command "pppoe-client dial-pool-number". I check the old modem FTTH, they also config VLAN 10 in Wan interface. I tell ISP why we have the same two FTTHs, but two differrent config ways. ISP says because the two line run in two different infrastructure, two different devices. I don't know how to do now? stay in customer side or ISP side. Here is my PPPoE config:
interface FastEthernet0/0
no ip address
duplex auto
[Code].....
View 4 Replies
View Related
Sep 3, 2012
What commands do I need to enter to correctly authenticate with my DSL PPPOE provider? I need to have the ID and Password entered into the router.
View 19 Replies
View Related
Jul 16, 2012
we have cisco 1801 router and want to configure for PPPoE.As our ISP has provided adsl connection having following settings:
Encapsulation: PPPoE
Multiplexing: LLC based
VPI = 0
VCI = 103
Login =xxxxx
Password =xxxxx
IP: dynamically from ISP
configuring cisco router 1801 for above configuration.
View 5 Replies
View Related
Sep 6, 2012
I have DSL 8Mbps DL and 768kbps UL The setup look like this:Internet -> Modem -> Cisco Router -> Firewall -> Switch Core - > Multiple switches like sfe2000p? CiscoRouter: i use port gig0/1 for PPPoE and i use port gig0/2 for LAN static Router port gig0/2 with 122.54.144.153/29 connected directly to Firewall port13 with 122.54.144.154/29 ?i want 122.54.144.153/29 will my default gateway ? include no limit bandwidth,filter etc at router, Firewall will be DHCP Server and control the bandwidth, filtering etc and the client computer should get 8Mbps
Mode: Routing
Encapsulation: PPPoE
Username: xx
Password: xx
Service Name: ISP name
[code]....
View 9 Replies
View Related
Jun 10, 2012
when I'm trying to configure my router 1801 with PPPOE I have the message below "% PPPoE config from vpdn-group is converted to pppoe-profile based config.% Continue PPPoE configuration under 'bba-group pppoe global'.
View 3 Replies
View Related
Apr 27, 2011
I plug my modem into the router, and apparently to configure it I need to put my settings into the router, but PPPoA is not in the dropdown, only PPPoE and PPTP. What do I do?
View 1 Replies
View Related
Dec 18, 2010
how to configure the Cisco 1941 router for PPPOE with dynamic IP
View 10 Replies
View Related
May 3, 2013
I m getting the below debug log and can not get IP from my ISP. It is static IP address and there is modem in bridge mode for the adsl line.
Below Conf and debug out put,interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
end
[Code]....
View 3 Replies
View Related
Apr 8, 2012
i have a Dlink DSL-2730U (an expensive, el cheapo router devoid of any functionalities, which also offers a way to connect to net as a side feature).basically i need to disconnect / reconnct pppoe without rebooting the router. but theres no button on the wan page for doing so.i noticed clicking on most of the buttons redirect to some non-html urls, like .cmd, .cgi etc, and some of them are common for many routers. e.g. on my router, "reboot" takes me to
[url]...
View 18 Replies
View Related
May 3, 2011
I am using a PPPoE connection on a linksys WRT54G router and trying to set up an Edimax EW-7206APg to extend my wireless connection range.I followed the instructions given on the Edimax manual, but that seems to be for a DHCP connection. Is there anything different I need to do to configure the Edimax repeater on a PPPoE connectionMy router IP ("Local IP address") shows 10.10.0.1 instead of the "192.168.1.1" that all the documentation online seems to suggest. What am I doing wrong?
View 2 Replies
View Related
Dec 24, 2010
There is one router ( SWR54BGA ), wan interface functional ( connected as a dhcp client to the lan interface of another router , packets are forwarded). When i connect the wan interface to the isp line, and provide the pppoe login details ,it won't work. When i try to connect manually to the pppoe server from the wan configuration page, after about 30 sec i get the connection failed message.Is the firmware corrupt, should i go the ddwrt route?
View 2 Replies
View Related
Feb 11, 2012
I've got problem trying to connect the CISCO-887VDSL/ADSL OVER POTS ROUTER to internet. Only got the LAN part working.I'm trying to setup PPPoE with dynamic IP Followed CISCO's documentations but the commands used were not recognized by the router.
here's my config.
!
! Last configuration change at 08:31:51 UTC Sat Feb 11 2012
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 1 Replies
View Related
Jan 5, 2013
I have 2 public ip, 1.1.1.1 anda 1.1.1.2. I'm connected to the ISP using PPPoE. I also have a router and a firewall. I want to assign 1.1.1.1 to router and 1.1.1.2 to the firewall. I do not want to NAT 2 times (one in router and one in firewall)That's why i want to bridge Fa0/0 and Fa0/1.Could this be done in Cisco router? I've done this command but it's not working as i want. I'm using bridge irb and bridge-group.
View 6 Replies
View Related
Sep 19, 2010
I installed a Linksys WRT54G2 router earlier this year and set my Siemens modem from AT&T(Actually from SBC before the two merged) in bridge mode. I did this so I could change the NAT setting on our internet, which was interfering with my Xbox. It worked for about 4 or 5 months with little to no problems. Recently, however, the internet has been disconnecting and when I check the status page on the router it says it is disconnected. Sometimes clicking on the connect button will work, but usually it will say "Connecting" and keep refreshing the page for a little while without any change, then give me a message saying it couldn't get the IP from the PPPoe server. Turning it and the Siemens modem on and off and fiddling around seems to solve the problem, but only temporarily. Interestingly enough, I don't think it ever interferes with my Xbox. Until recently, the Xbox was set as the highest priority on the QoS page, but I changed the computer to the highest priority and it hasn't worked. In addition, the small, thin green light bar just below the Linksys logo on the top of the router has just recently started changing to orange occasionally
View 9 Replies
View Related
Sep 22, 2011
I have e3000 but in VPN Passthrough I don't have ( pppoe passthrough ). Just I have is ipsec + pptp + l2tp only. How could I add ppoe passthrough in my e3000.
View 2 Replies
View Related
Nov 17, 2012
I've been using my EA4500 since it's original launch date as a PPPoE router through another router/modem which is the Netgear DG834G V4 set to Modem Only mode which was working fine for a long time!A month ago, a friend wanted to borrow the Netgear Router and after he gave it back I reset it like I always do and entered my settings in router mode(i.e. username and password) to check if I havewe working Internet connection and that the router is working properly and it was working properly like it was before I lent it. Now comes the problem, if I keep using the Netgear router as the PPPoE handler and make the EA4500 work as "Automatic Configuration DHCP" it works flawlessly but if I set the Netgear router to modem mode and make the EA4500 handle the PPPoE connection, the report in the troubleshooting tab keeps on saying "Connecting" endlessly!
Note: I've replicatedthe settings that I used on both router before and after lending it to my friend so there's no difference in settings!
View 6 Replies
View Related
Nov 17, 2012
I have a Linksys WRT310N V1.I am trying to connect this via PPPoE to another Thompson router/modem that has been succesfully switched into BRIDGE mode.The Linksys router is conneted via ethernet cable to an ehternet port on the Thompson router.The ADSL cable is pluggedinto the WAN port of the Thomson 'bridge'.There is no cable in the WAN port of the Linksys router.
The Linksys router is set up to connect over PPPoE using the username and password that was given to me by my ISPs tech support (checked and double checked).The DHCP server on the Bridged Thomson is set to ON. DNS is set to OFF.the DHCP server on the Linksys router is set to ON.
View 2 Replies
View Related
Jul 22, 2011
I recently bought an E3000. I am trying to setup a wireless home network.Google and tried a lotta things (power cycle the most no. of times ). Nothing worked.So I poked around. Looked up the IPConfig of my PC with wire connected directly(no router), was 192.168.0.xxx. So I hit 192.168.0.1 in my browser address bar, and it came up with the login page for a D-Link DIR600. A wireless router with wireless disabled. Apparently this is being used as a switch by my ISP. This I know cause I checked the active connections and DHCP reservations on the D link and it showed up about 100 different PC's (including MAC and IP addresses).
View 9 Replies
View Related
Aug 20, 2011
I have e3000 but in VPN Pass through I don't have ( pppoe pass through )
Just I have is ipsec + pptp + l2tp only
How could i add ppoe pass through in my e3000
View 1 Replies
View Related
May 3, 2011
I am using a PPPoE connection using a linksys WRT54G router (working perfectly) and am now trying to set up an Edimax EW-7206APg to extend my wireless connection range. I followed the instructions given on the Edimax manual, and while my devices (iPad, laptop) got connected to the new repeater network, I could not access the Internet from it. I may be wrong, but the instructions on the Edimax manual seemed to be for a DHCP connection. Is there anything different I need to do to configure the Edimax repeater on a PPPoE connection?My router IP ("Local IP address") shows 10.10.0.1 instead of the "192.168.1.1" that all the documentation online seems to suggest.
View 6 Replies
View Related
Dec 27, 2012
I extremely need PPPoE Dual-Access on my EA6500.I'v paid $225 and can't watch IPTV So, I'm somewhat disappointed with tis issue...
View 9 Replies
View Related
Oct 4, 2012
I was assigned a static block over PPPoE from the ISP. I can connect to the internet using the gateway address but I need to route the other static IPs to my servers. I might say that I accomplished it on a couple of older routers - E1200 & WRT120N, but I cannot get it to work on my new EA3500. I have 5 usable IPs plus the gateway IP that is assigned with the PPPoE connection on the WAN port.
View 8 Replies
View Related
Aug 2, 2011
I have a WRT54GS wireless router. I can successfully set up the router with my DSL modem for PPPoE. Here's my problem. The router configuration requires you to put in the userID and password, then logs you in to your ISP automatically. I DON'T want it to do that. Is there any way to configure for PPPoE where ISP login is controlled manually; i.e., when the user tries to connect to a web page, a dialog pops up for entering the password?
View 1 Replies
View Related
Sep 20, 2012
I have been working on this for hours and getting frustrated! This router has been set up for over a year with no trouble, but recently had trouble connecting with my wireless devices and was kicking my wired (ethernet) laptop off when it is usually on all the time.
Now, my wired connection works through the router, the wireless devices all connect to the network but do not have access to theinternet. From the router's setup page, when I enter my PPPoE information and go to status and connect, it tries to connect a few times then gives me the error message 'cannot get IP address from PPPoE server"
I have tried updating firmware, resetting, restarting, recycling power, chat support with ISP and chat support with Linksys. Have verified my username and key and those are correct otherwise I'd have no internet access at all. I do have wired access but not wireless. The wired connection does go through the router.
Bridging - my modem is a bridging modem only, so it shouldn't be that.
View 4 Replies
View Related
Oct 24, 2012
When the ethernet cable is plugged directly into my laptop i can input my user name and password and connect directly without a problem. But as soon as i plug the cable into the router, the activity lights turn off like its not plugged in on the other end...which it is. So when going through the setup process, both using the cd and inputting the information on the web based setup. It does nothing, the automatic setup says the cable isnt plugged in. When using the browser setup i can click connect as many times as i want and it does nothing but say disconnected.
View 9 Replies
View Related
Dec 22, 2012
I look forward to the new firmware can improve this problem.
View 3 Replies
View Related
Feb 18, 2012
I am using wrt54gx4. I have a IP camera connected to it. I can view the live images on the intranet and internet. Not too long ago my DSL company upgraded my DSL modem to a newer model. Then I can not connect to the internet by PPPoe. DHCP is fine. So the only connection type works is DHCP. But now I can not view the live images on the internet. I can only view the live images on intranet( I mean if I open web browser and type url.. is the port, I can view the live image).
View 1 Replies
View Related
