Cisco WAN :: E1 - No Cct Channel Available
Mar 13, 2013I have configured E1 to use PVDm to terminate ISDN connection but I keep on getting the above error message
Layer 1 and 2 seem to be working fine but layer connection isn't working.
ADVERTISEMENT
What Channel To Be Used
Mar 14, 2011My neighbors all use 1,6, and 11. what channel should I use?
View 3 Replies View RelatedCisco :: Port - Channel Sub Interface QoS
Sep 2, 2012I have Cisco 3845 with two Gigabit interfaces configured as port-channel with sub interface and with QoS. However shape does not work.
[code]...
Cisco :: Ipsec On Noisy Channel?
Nov 15, 2011I have a couple of clients which connection to our network via intranet to our VPN.Clients using the 3g connection to connect to the internet .The encryption is DES.But some of them due the bad channel(poor coverage,non-stable channel and etc) cannot conne to my asa with vpnc(the cisco ipsec client for *nix) .They have this problem - vpnc: expected xauth packet; rejected: (ISAKMP_N_PAYLOAD_MALFORMED)(16)[CODE]
View 2 Replies View RelatedCisco WAN :: 3110 - Channel Cannot Be Up After Reload
Jun 11, 2012In our project, we had to configure PAGP between catalyst cisco 3110. there is no problem in configuration of PAGP and everythin is ok,and channel is up.but after reload cisco, chanel can not be up and between switches all packet are in loop between 2 switches.in order to solve this probelm I have to shutdown all port and again create chanel for every port.
View 12 Replies View RelatedCisco :: 1242AG / Change RF Channel On APs On NCS?
May 30, 2012I'm looking to make a few adjustments to out wireless network and need to change the RF channels on a few APs.I've logged on to NCS went into the AP, an 1142N, then the Radio 802.11 b/g/n and changed the RF channel under custom.Once I pressed the save button the channel reverts back to its original channel. I've also tried this on a 1242AG the same thing happens. I then went to the controller and tried to change the RF channel there and it took the change. I pressed apply logged out went back to NCS made the change under custom and again it reverted back after I pressed the save button. I went back into the controller and the channel had also reverted back even thought it gave the impression it took the changel.
View 1 Replies View RelatedCisco Wireless :: 2112 WLC Using All Of 5.0 Ghz Channel?
Sep 25, 2012I have a 2112 wlc and 6 1142ap's. I noticed that the 2.4ghz channel is filled with lots of networks but the 5.0ghz area is empty. I tried to manually change the channel but it keeps reverting back to 2.4.
View 11 Replies View RelatedCisco WAN :: OC-48 Throughput With Fiber Channel
Jan 12, 2011We've recently moved from using FiberChannel across an OC-48 between two data centers to GigabitEthernet. Data replication throughput has dropped from 700Mbps down to 45Mbps. The telco provider has demonstrated 1Gb throughput via UDP andTCP using T-Berts. However, when we connect two computers or servers, we do not get near the throughput performance.
View 1 Replies View RelatedHow To Change Channel On Router
May 14, 2012I need to know how to change the channel on my router so I do not keep getting disconnected when my telephone rings
View 2 Replies View RelatedCisco :: What Is Active / Passive Port-channel
Feb 7, 2013what is active/passive port-channel..? and how it will do load balancing when my network traffic is flowing on both the ports.
View 5 Replies View RelatedCisco Infrastructure :: Getting Channel Usage From 3845?
Dec 14, 2010I am trying to get channel usage from our 3845 with C3845-ADVIPSERVICESK9-M), Version 12.4(20)T4, RELEASE SOFTWARE (fc4) using snmp with no luck.I am going after cpmActiveDS0s or cpmDS1ActiveDS0swith no luck. also tried isdnBearerOperStatus with no success. I get sub-id not found.I did a snmp walk and these objects exists. ( Also tried snmpget -v 2c -c ****** ***.**.**.*** 1.3.6.1.2.1.10.20.1.2.1.1.2 with no success)What am I missing and how to I install them?
View 6 Replies View RelatedCisco WAN :: 3845 Port-channel Sub-interface QoS
Sep 13, 2012I have Cisco 3845 with two Gigabit interfaces configured as port-channel with subinterface and with QoS.However shape does not work, why? [code]
View 1 Replies View RelatedCisco WAN :: Port-Channel Supported On 6500s -w- SUP-2T?
Nov 2, 2012are port-channel interfaces supported in 6500s -w- SUP-2T?
Inquiring if able to bundle a couple of 10GB ports on a 6908 via port-channeling.
12.33 IOS doesn't it, but haven't completely confirm whether 15.1 IOS does.
Cisco Wireless :: 1262n - 40 MHz Channel Width On 802.11n
Mar 8, 2012I got new cisco aironet 1262n Dual band Access-point running IOS version 12.4(23c)JA .my question is does this access-point support 40 MHz channel width on the 2.4 Band on any IOS version as the command "Channel width" under interface dot11radio 0 allow only 20 MHz
View 18 Replies View RelatedCisco Firewall :: Port-channel On ASA 5520
Jun 11, 2013So everything I've read on Cisco's documentation here: URL says that I can create a port-channel on two physical interfaces that will uplink to a VSS pair. However, the command is not recognized. What am I missing? I've tried executing "channel-group #" on the physical interface and tried creating the port-channel 1st and neither commands exist. I haven't seen it listed anywhere if it is only available after a specific piece of ASA software. If it is the software what version at a minimum I need to upgrade to? Below is an output from a show version
Cisco Adaptive Security Appliance Software Version 8.0(4)
Device Manager Version 6.1(3)
Compiled on Thu 07-Aug-08 20:53 by builders
System image file is "disk0:/asa804-k8.bin"
Config file at boot was "startup-(code)
Cisco Wireless :: WLC 4402 Update 7.0.253.3 - All 17 APs Use Channel 1
Dec 16, 2012Since the update of our WLC 4402 to v 7.0.253.3 all 17 accesspoints are using channel 1 !!
View 2 Replies View RelatedCisco WAN :: 2800 - Limit Of T1s In Channel Group
Jun 22, 2011I can't find the theoretical limit of T1s in a channel group on a 2800. I know that you can have 2 channel groups per V Wic 2, but it doesn't say how many T1s I can have bonded. I think it's 8, but I can't find it in writing anywhere.
View 3 Replies View RelatedCisco Wireless :: Can't Choose Channel For WAP4410N
Mar 16, 2013I have been having some connectivity problems and one suggested solution was to upgrade networking firmware. I did this for our router (Cisco RVS4000 v2) and it didn't work, so I moved on to the wireless access points (two WAP4410N). Before doing that, I also reset both to factory default settings - neither would respond to pressing the reset button but it seemed to work using the web interface for both.
Before I did anything to the WAP4410Ns, I noticed they were connected in B/G/N-Mixed mode to channel 6. Now the wireless network mode is stuck on Disable. I can choose B/G/N-Mixed from the dropdown list, but can't choose a channel - the dropdown list for that is empty. And if I try to choose Save after choosing B/G/N-Mixed, it reverts to Disable.
Change The Channel For Wireless Router?
Aug 25, 2012How do I change the channel for my wireless router?
View 1 Replies View RelatedHow To Change The Wifi Channel Of A Hotspot
Mar 24, 2011I need to know how to change the wifi channel of the connection. connectify can't do it. I guess you have to set it somewhere in the network card settings, but I'm quite a noob when it's about wireless network. googling my problem didn't get me any good result since all the threads about channel setup are about modem/router wifi channel setting, can't find anything about hotspots.
View 7 Replies View RelatedChange D-link 615 Router Channel
Oct 11, 2012How do I change my dlink 615 router channel?
View 1 Replies View RelatedN450 Router And WAP- Same Channel Range Of Different?
Oct 5, 2012I have my buffalo N450 router working great and have installed a Belkin 600HD as a wired WAP. Now I am trying to fine tune them to get the greatest coverage and throughput. What do you guys recommend in terms of channel selection. Should I try to cover different channels with each router or keep them the same? I have been using inSSIDer to try and watch the strength and width of various settings. It seems I get better strength (at least according to Windows 7) when I have the channels set the same.
View 4 Replies View RelatedCisco :: Moving A Port-channel Without Taking Down Traffic?
Mar 6, 2012So I have a current port-channel between two 6ks that I need to upgrade. There's too much traffic and the port buffers on the SUP7203B sort of suck. Microbursts are causing overruns like mad. Im going to move the 2x1gig port-channel to a 6724 and make it a 3x1gig port-channel. The switches carry production traffic across the link to the tune of about 400 meg during the lowest load time. Initially, I thought that I couldn't move the port channel without temporarily taking down the link but I think I have a workable solution now. Has anyone done this successfully before? Im curious what others have done. Also, to make matters worse, the existing port-channel is 'mode on' and I want to migrate to 'mode active' in the new channel
View 7 Replies View RelatedCisco :: Inter VLAN Routing With Port Channel
Oct 30, 2012I want to do the inter vlan routing packet tracer file url...configuration of MLS are as bellow can anyone tell me why vlan on switch0 can not ping vlan on switch1. [code]
View 12 Replies View RelatedCisco :: Ipsec Isakmp Does't Work / Sometimes Noisy Channel
Dec 14, 2011I have a couple of clients which are using the 3g modem to connect to ASA.The channel was sometimes "noisy" and therefore ipsec isakmp is doesn't work.Client losts vpn connection ,but on asa i can see it as connected(connection was in "freeze" state).
It's look like this :
[code]...
Cisco Wireless :: WISM2 No Port-Channel On 6504-E?
Jan 18, 2013I have just been setting up a WISM2 in a test lab and for some reason the Supervisor is not creating a port channel on my 6500 as suggested in the WISM2 Deployment Guide. WISM2 is installed in an appropriate slot (according to same doco) and have attempted reset to factory defaults, removing and power cycling several times.
View 1 Replies View RelatedCisco WAN :: Configure 2801 With Multipoint Port Channel
Jan 5, 2012Is it possible to configure a Cisco 2801 router with Multipoint Port Channeling? A service provider dropped a 4.5Mbps ( 3x T1s ) to one of our customers without any equipment. They assume the CPE responsible. If so, any links to documentation on this configuration. If not, what device will they need to buy from Cisco that can bundle these 3 T1s together then feed it into their router?
View 6 Replies View RelatedCisco WAN :: Port-channel Between Nexus 7000 And 55900?
Jan 16, 2011I have configured my Nexus 7018 and 5548 as follow (see diag attached).Both 7000 and 5500 are vPC pair(po1and po2). Now I have created port-chanel between 7018and 5548 as port channel PO3 on 5500. Would it give me 20g bandwidth as PO3?or 10g only uplink to 7018? Do I need to config all four 10g links in PO3 on both 5500 and 7000 switches to achieve max b/w and failover?
View 4 Replies View RelatedCisco Wireless :: 3xLAP1242 Force Channel Change On LAP
Aug 27, 2012I have 3xLAP1242 in a building that are some what close to eachother (WCS show them as Rx Neighbors). The problem is that they are all running the same channel, 1 on 2.4GHz and channel 140 on 5GHz. [code]Ether I get these log messages because they are on the same channel or because there is something blocking the other channels.Can I force a channel change on the LAPs somehow? Not manualy setting the channels, but forcing the LAPs to redo their channel calculation/algorithm.
View 12 Replies View RelatedCisco WAN :: Nexus 5K (version 5.0.3) With Port-channel Bandwidth?
May 22, 2012I have port-channel configured on Nexus 5K (version 5.0.3) with below configuration.
interface Ethernet1/9
switchport mode trunk
switchport trunk allowed vlan 60
speed 1000
channel-group 105 mode active
[code]....
We have added GLC-SX-LH module to E1/1 and E1/10 and speed is set to 1000 (1Gig) Now other side of E1/9 and E1/10 are not connected. Port-channel status is down
Po105 1 eth trunk down No operational members 1000(D) lacp
show interface port-channel 105 shows different bandwidth (100) MTU 1500 bytes, BW 100000 Kbit, DLY 10 usec,question is under interface port-channel105 speed 1000 command inserted automatically.Now if we connect otherisde of interface, during port-channel comes up.what will be the port-channel interface bandwidth ? will it change to 2Gig(2000). Why speed 1000 command inserted automatically on port-channel.Since it is migration, we want to be more specific on the port-channel configuration?
Cisco WAN :: Load Balance Of 3750 Port Channel?
Jul 17, 2011What is the load balance method of 3750 port channel ( by source ip , or by source mac ) to diver traffic to paths? I have tried to use 10.242.104.101 and 10.242.104.102 as source ip, it will travel to the same link (G0/1) within one port channel (G0/1+G0/2). Howerver, if I later use 10.242.104.109, then this time it will traffic to G0/2 link. What's the concept behind.
View 1 Replies View RelatedCisco Switching/Routing :: Will All 4-ports Of N5K Will Be Same Port-channel
Sep 12, 2012Have 2 N2K with dual-connections to both 2 N5K, will all 4-ports of N5K will be the same port-channel. N2K as well ?
View 1 Replies View RelatedCisco Wireless :: 1142n Autonomous Configure Channel
Jun 18, 2012I have 14 unit of Air-AP1142n. No controller. All unit were in a warehouse, each of the AP distance each other around 40mI would like to use only 4 SSID instead of 14 SSID.
View 5 Replies View Related