Cisco Wireless :: WLC 4402 Update 7.0.253.3 - All 17 APs Use Channel 1
Dec 16, 2012Since the update of our WLC 4402 to v 7.0.253.3 all 17 accesspoints are using channel 1 !!
View 2 Replies
ADVERTISEMENT
Cisco Wireless :: 4402 - Setting Update Time For Auto Tx Power Level Assignment
Dec 1, 2011We have a WLC 4402 controlling 40+ LWAPs. Is there a way to keep Tx power level assignment dynamic, but set the time of day it does it? I'd like to minimize user impact. (Firmware v. is 7.0.116.0)
View 2 Replies View RelatedCisco Wireless :: Can't Get APs To Recognize 4402 WLC
Nov 20, 2011I have 2 4402 WLC's and am in the process of deploying 1042 APs out to sites. But The AP's wont recognize the WLC. I have configured the DNS for CAPWAP but still no dice. I have had to serial into each unit and give it a static IP and then I can see it on the WLC. Shoulsnt this be automatic?
View 21 Replies View RelatedCisco Wireless :: WLC 4402 Has Detected Its IP Add Being Used By Mac
Jul 29, 2010Any explanation about this warning from the WLC4402 after the software upgrade to 7.0.96. version? this is the message: Warning: WLC has detected its IP add xx.xx.xx.xx being used by a machine with MAC add xx:xx:xx:xx.and the MAC add found is the the mac add of the dynamic interface of the WLC.
View 7 Replies View RelatedCisco Wireless :: 4402 WLC Cannot Join More Than 47 APs
Jun 29, 2011My WLC running 6.0.182.0 suddenly could not accept more than 47 APs! Ihave a 1240 trying to join but failed with no obvious reason (no special errors in debugging).
I unplugged one of the joined and the first one joined!! I replugged the second one but could not join!! I unplugged the first one and replugged the second one: the second joined the controller but the first could not associate again!
Cisco Wireless :: AP Supporting 4402 WLC?
Jun 25, 2012Can 3600 series model AP work with WLC 4402 with existing license, we purchased 25 LIC pack and still using only 15. Any recommended Part no on 3600 series with external Antenna
View 5 Replies View RelatedCisco Wireless :: 2112 WLC Using All Of 5.0 Ghz Channel?
Sep 25, 2012I have a 2112 wlc and 6 1142ap's. I noticed that the 2.4ghz channel is filled with lots of networks but the 5.0ghz area is empty. I tried to manually change the channel but it keeps reverting back to 2.4.
View 11 Replies View RelatedCisco Wireless :: AP 1262 Cannot Join WLC 4402
Jun 7, 2012We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
Cisco Wireless :: AAA Authentication Failure On WLC 4402?
Jun 13, 2012Error: AAA Authentication Failure for UserName:radiususername User Type: WLAN USER
I am using a window radius server. I have added my WLC 4402 as a radius client on my radius server.
I followed the instructions on the MS link : [URL]
I want to use my windows raduis authentication for WLC management login and Web-Auth for guest WLAN user login.
Cisco Wireless :: 4402 Code Upgrade To 7.0.230.0
Feb 3, 2013Our company has a customer with a Cisco 4402 WLC and a code version of 4.2.130.0 . The customer wants to upgrade the code to 7.0.230.0. Is there any flash size requirement when upgrading to 7.0.230.0? (upgrade train: 4.2.130.0 ----> 4.2.209.0 ----> 7.0.230.0), How can I find the flash size?
View 2 Replies View RelatedCisco Wireless :: Configuration Migration Of WLC 4402
Feb 3, 2013We got WLC 4402 running software 7.0.235 and would like to backup the configuration and restore on 5508. Is this doable? Do we need to be on the same version as WLC 4402. How to get cisco document to follow the steps if the above is doable,5508 is new with no setup.
View 6 Replies View RelatedCisco Wireless :: How To Connect One 5508 And 4402
Jan 16, 2012I need to install one 5508 and a 4402 together to bring redundancy to a wireless environment.Can I do this?. What are the neccesary steps to perform this?, the idea behind this is to bring redundancy is the primary WLC falls for any reason.
View 4 Replies View RelatedCisco :: Wlc 4402 - Wireless Client Ip Address?
Mar 7, 2011I have two wlc 4402 to control 50 AP 1131. 2 WLC: wlc-01 and wlc-02, wlc-02 config as backup wlc in the same mobility group. Client authentication:EAP with Microsoft IAS/AD.All AP have joined wlc-01. Wireless client work well with wlc-01.For testing I config access point AP01 have primary wlc: wlc-01, secondary: wlc-02 If I change config of AP01 like this: primary wlc: wlc-02, secondary: wlc-01. Client is hard to connect to wlc-02 and it only connect when client set static ip ALL wlc run this softwar image: 7-0-98-0 Should I send wlc-02 to warranty service?
View 8 Replies View RelatedCisco Wireless :: 4402 Could Not Register IP Add On MSCB
May 17, 2012I do get this error all the time on my WLC 4402 logs:
"Could not Register IP Add on MSCB. MSCB still in init state. Address:e4:ce:8f:13:e4:de[...It occurred 2 times.!]"
Cisco Wireless :: WLC 4402 Ver 5.1.151.0 Working With Air-ap1041n-e-k9?
Jul 18, 2012I have WLC 4402 working with AIR-AP1131AG-E-K9. Need to buy another pair. I looked to the side air-ap1041n-e-k9. Tell me whether or not the compatibility of the controller and the AP1041n? One more question. When buying in 1131 is still in the box and power cord to the point. The new 1041, the purchase comes with the point of the power cord?
View 13 Replies View RelatedCisco :: 4402 WLC Guest Wireless Setup
Jul 24, 2012I am trying to setup a Wireless Network on my WLC that is totaly independent of our internal LAN. Port1 is designated at the .14.0 network and Port2 is the .18.0 network. The 14 network (Port1) will be the guest and 18 network (Port2) the internal wireless.
The issue i am having is nothing is routing to Port1. I have the Guest Wireless set to get DHCP from the WLC and i can get an address but i cant get internet access. I tried configuring a Network Route but it will only let me set the service port as the Gateway and not the IP for Port1.
I am running software version 5.1.151.0 and using this guide as it is the only one i can find. [URL]
Here is a screen shot of my Interface config.
Cisco Wireless :: Web Authentication Using LDAP On WLC 4402?
Dec 18, 2011We are attempting to use LDAP for web authentication on a WLC 4402.
[URL]
You are able to connect to the SSID and it reidrects you to the login page as it should. When you enter your username and password you get a message that "the username and password combination you have entered is invalid." Based on the following log it looks like the LDAP bind is the issue.
*LDAP DB Task 1: Dec 19 11:19:26.584: %AAA-3-LDAP_CONNECT_SERVER_FAILED: ldap_db.c:1038 Could not connect to LDAP server 1, reason: 1005 (LDAP bind failed).
We are able to test the following configuration with ldp.exe successfully,
Server: ***.***.***.***
Port Number: 389
Bind Username: CiscoBYOT
[Code].....
Cisco Wireless :: WLC 4402 No Boot-up Dead
Jun 22, 2012I tried to upgrade the cisco boorloader pf WLC 4402 from version 4 to 7.2. I updated ER.Aes FOR 7.2 (EARLY RELEASE.aes). It was updated perfectly and then I rebooted controller....now i can only see blank screen from connected console.I tried the flash of other lan controller but its not working because the issue is in the ROM as the boadloader file is in the ROM which is corrupted now i want the solution to upgrade the boatloader file inside the ROM.
View 1 Replies View RelatedCisco Wireless :: 5508 As Backup For 4402-25-K9?
Jun 12, 2012My customer has a 4402-25-K9 and need a backup (failover) controller to avoid data transmision break when primary controller goes down.4402 are end of sale so I have a question can I use 5508 to get Controller Failover Protection with 4402 ?
View 3 Replies View RelatedCisco Wireless :: AP 1262 Cannot Join WLC 4402
Jun 6, 2012We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC.
The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL]
Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
Cisco Wireless :: AP Fallback Not Working With 4402?
Apr 12, 2012I have an issue with AP Fallback not working with two Cisco 4402-50 WLC's. Here is the senerio:
Site 1 has a 4402 (WLC01) running software 7.0.220.0 with 48 associated access points. AP Fallback is enabled in Controller > General and all 48 AP's are set to Critical failover with WLC01 being the primary controller and WLC02 (at site 2) being the secondary.
Site 2 is the location of WLC02 which is also running software 7.0.220.0 but has 0 ap's associated and also had AP Fallback set to enabled.
Your typical active/passive setup
The problem is when WLC01 goes down all of the AP's fail over to WLC02, however when the connection is restored to WLC01 we have to manually reboot each access point in order for them to reassociate back to the primary controller. Isn't AP Fallback enabled suppose to allow the AP's to move back to the primary controller once connection is reestablished?
Cisco Wireless :: WLC 4402 Software Upgrade
Nov 7, 2011I ##have a customer with WLC 4402 in use, running software version 7.0.98.0, and supporting 11 APs at present. The customer wants to enlarge the WLAN, which involves increasing the number of APs. I #####have purchased a new WLC5508, and have installed it onto the network alongside the 4402. the 5508 is running software version 7.0.116.0. Because the wireless network is critical to the user, we want to move the APs over to the new controller while the network is up and running, then remove the 4402.
However, when we set the 5508 as the master controller, or tell one of the APs to use the 5508 as its primary controller, the AP connects to the new controller, downloads the new software version, attempts to load it but reports an error with the unzipped file size of the software and fails to boot. formatting the flash on the AP, then disconnecting the 5508 from the network and rebooting the AP allows it to connect to the 4402, it downloads the older software and boots as normal. A new AP, if connected to the 5508 in a test scenario (ie no 4402) connects, downloads and boots perfectly.
I #have the upgrade software to allow the 4402 to be upgraded to 7.0.116.0, but I am concerned that, if this is installed, the existing APs will then fail to boot from the 4402 or the 5508.all APs are 3502s, running IOS version 12.04(23c)JA when connected to the 4402 and 12.04(23c)JA2 on the 5508.
Cisco Wireless :: WLC 4402 No Network Access
Mar 11, 2013We have two WLC 4402 WLC in active-active mode in our setup. The issue we see is that a user/laptop gets connected and gets the ip address but there will be no network access. We see a yellow exclamation sign at this time in network icon in tray and we can not ping gateway at this point. We have run debugs at this time for the machine and we could see that was in "RUN" state its only that the machine can not access network.
View 11 Replies View RelatedCisco Wireless :: WLC 4402 Upgrade Up From 5.1.151 HTTPS
Mar 24, 2012I 'm trying to upgrade WLC 4402 up from 5.1.151. After upgrade to 5.2 or higher https interface is inaccessible. If I use any other previous version, all is OK. Somewhere I found recomendation to open http before upgrade and use it at first. It works, but what to do next? To stay on http only?
View 1 Replies View RelatedCisco Wireless :: Upgrading From 4402 To 5508?
Jan 4, 2012Any instructions on performing an upgrade from a 4402 to 5508?
View 7 Replies View RelatedCisco Wireless :: Cannot Console Into WLC 4402 After Upgrade
Apr 23, 2013my client claimed that right after thry upgraded their WLC 4402 to version 7.0.220.0 from the version that came preinstalled (factory) the can no longer console into the device. They were able to console into the 4402 before the upgrade but now they can't. I'm thinking that maybe they upgraded straight to the new version and didn't verify to see whether they were allowed to upgrade directly to that version 7.0.220.0 or if they needed to upgrade to a intermediate version , the proceed to upgrade to the 7.0.220.0.
View 3 Replies View RelatedCisco Wireless :: WLC-4402-25-K S/W - Upgrade Went Wrong
May 3, 2012WLC-4402-25-K S/W - Primary and Secondary Controllers were running 4.2.130 to begin with. Customer upgraded remotely using NCS - Primary to 4.2.209 and then to 7.0.230 and all that went fine and is in Production.
Then customer upgraded Secondary also using NCS also from 4.2.130 to 4.2.209 in preparation to upgrade to 7.0.230 and he lost contact with the controller. Sent a technician to site to troubleshoot by connecting to Serial Port. Technician #ESCAPED out of the boot sequence and from the BOOT MENU tried to boot the Primary Image and it failed with CRC error on Flash. He then tried to boot the Backup image and had the same problem. He then tried to manually load 7.0.230 - ER (Boot Software) using TFTPD32.EXE and that went fine. He then tried to load 7.0.230 "aes" S/W - The big over 70 MB file and went through most of the file transfer but failed saying:
ERROR: Transfer Failed.
TFTPD32.EXE said something like "Data Packet too Short or some such thing". Sorry did not write down what TFTPD32.EXE said.
Then we thought "may be" a power cycle of the unit is required after the ER Boot Loader Image was loaded. When we did that the unit died. That is - no communication with the Serial Port. We don't think we have any choice other than RMA - Do we?
Customer says he did read and follow this link - especially Table 10-1. {URL}. He said he used NCS to do the Upgrade. I a not familiar with NCS.
Cisco Wireless :: 4402 WLC - Get Network For Guests Instead Of DMZ
Nov 4, 2012we have a two port 4402 WLC here with only one port currently in use. The topology is bacically the used port uplinks to a dmz switch. Our Intranet and the Internet are accessed via an ASA from the WLC. The WLC also sits in the DMZ. This WLC is only used for guest wireless access. The AP information and traffic is exchagned from a primary WLC on our Intranet and authentication is done via RADIUS. Internet access is handled through the ASA as well on the DMZ. We have a completely independent ISP broadband connection here that was put in long before I was ever here and is used for guest wired web access. All ports are clearly labelled and have bright pink patch cords. What I would like to do is have our wireless guests be on that network rather than our dmz for their web access. I have pulled an ethernet cable from the switch that connects to that broadband connection to the cabinet with the 4402. So the physical is fine right now. I'm not all that familiar with the WLC's, so I'm not sure if everything else can remain the same as it is right now, but just connect the second port to the broadband connection and route guest Internet traffic through there rather than the DMZ.
View 1 Replies View RelatedCisco Wireless :: Broadcast Forwarding On WLC-4402-50-K9?
Sep 6, 2009I have problems to connect a MAC-Server from the wireless-network (WLC-4402-50-K9, Version 5.1.163). The wired clients doesn't have problems to connect to the MAC-Server. The connection works over broadcasts. The wireless-network don't forward this broadcasts. The broadcast-forwarding feature is activated. It is no problem to the MAC-server from the wireless-clients. The hole network is in the same IP-network (one broadcast-domain).
View 1 Replies View RelatedCisco :: 4402 - Unable To Access WLC From Wireless?
Nov 15, 2011We have a WLC 4402, with interface Management, AP-Manager, and only the ap-manager interface is enabled for dynamic AP Management, how can i enable the dynamic AP Management for management interface also. Because i couldn't access WLC from via wireless, only able to access it via wired.
View 15 Replies View RelatedCisco Wireless :: WLC 4402 Software Upgrade?
May 22, 2013I need to upgrade the software version of WLC to 7.0.235.3 with following primary and boot software:
AIR-WLC4400-K9-7-0-235-0-ER.aes
AIR-WLC4400-K9-7-0-235-0.aes
After the upgrade how the APs connected to WLC will download the IOS of new Software version. it is said that k9w8 - full lightweight IOS (this is what is bundled in the WLC .aes image, and is factory installed on "mesh" APs)
I want to be sure is this the IOS that the AP download after the Software upgrade??
Cisco Wireless :: 1262n - 40 MHz Channel Width On 802.11n
Mar 8, 2012I got new cisco aironet 1262n Dual band Access-point running IOS version 12.4(23c)JA .my question is does this access-point support 40 MHz channel width on the 2.4 Band on any IOS version as the command "Channel width" under interface dot11radio 0 allow only 20 MHz
View 18 Replies View RelatedCisco Wireless :: Can't Choose Channel For WAP4410N
Mar 16, 2013I have been having some connectivity problems and one suggested solution was to upgrade networking firmware. I did this for our router (Cisco RVS4000 v2) and it didn't work, so I moved on to the wireless access points (two WAP4410N). Before doing that, I also reset both to factory default settings - neither would respond to pressing the reset button but it seemed to work using the web interface for both.
Before I did anything to the WAP4410Ns, I noticed they were connected in B/G/N-Mixed mode to channel 6. Now the wireless network mode is stuck on Disable. I can choose B/G/N-Mixed from the dropdown list, but can't choose a channel - the dropdown list for that is empty. And if I try to choose Save after choosing B/G/N-Mixed, it reverts to Disable.