Cisco WAN :: WS-SUP-32GE-3B Possible To Configure VPLS Using Settings
Jun 10, 2012
We have 7606 with WS-SUP-32GE-3B. is it possible to configure VPLS using this settings or we need additional cards. as far as i have found googling is that either ES or SIP cards are required facing the core. But all are mentioned for SUPs other than WS-SUP-32-GE-3B.
I could do configuration of a VPLS in 3750, I have doubt about whether the configuration is similar to that of 7600, but is so I could recommend some document to observe the configuration.
I can't find any configuration info for any MPLS layer 2 extension features for the Nexus 7k devices, is this a strategic decision by Cisco to promote OTV?
I just installed Windows XP Professional on my Toshiba-X205 laptop and I am having a problem getting the OS to detect my NIC. I can not remember how to go into the control panel and configure settings so the OS will detect my wireless network or should i say i can not get my OS to detect my NIC so i can to connect to my wireless network. I think i may need to install the device driver for the NIC but i don't remember which driver i need for the NIC of my laptop and i can not find it on the Toshiba website, not supported anymore.
My company is moving the datacenter to our new building on Saturday, however the users will remain at the old building until late next month so they bought a 100M Metro E VPLS circuit through their ISP. I went to test it today but could not ping the workstation from my laptop. I wanted to do some bandwidth testing with iperf but could never get to that point because ICMP connectivity wasn't even there. From what I understand, VPLS is just a layer 2 extension so they way I'm testing the circuit below SHOULD work, but it isn't. Spoke with the ISP and they tested the circuit end-to-end on their equipment which was fine so am I missing something?
I have implement MPLS L3VPN on my network to provide service to customer and right now we plan to have service VPLS on our same router. What is needed to run the VPLS in our MPLS network ? I heard that we need addictional switching module and upgrade my IOS to support it but I am not sure.
One of our customer would like to connect 3 datacentres and decided to use VPLS to extend layer 2 VLANs . For this purpose they have bought six Cisco ASR1000 edge routers( two at each side).They also wanted to buy MPLS SP backbone but have decided to buy 2x10G dark fibre links instead.My question is,
1-Will it still possible to run VPLS over dark fibre? Because all the documents I read regarding VPLS are deployed over MPLS backbone.
2-Any sample configuration for implementation VPLS in ASR1000 ?
Does VPLS is supported on the Cisco ASR1001?With the feature navigator it looks like the ASR1001 is the only ASR1000 series router with VPLS support but I can't find any documentation confirming this.
i recently bought a hp 1219 model laptop with windows 7 ultimate...but i am not able to start wifi connections..i guess there is some installations for wifi drivers to make but when i tried it is not getting installed too.
I understood that service provider will use hardware Alcatel 6850 on the distribution/core and Zyxel 2108G on customer access level.query is that service provider says it's not VPLS which should work most probably through MPLS network of ISP.ISP noted that it would be direct 802.1q VLAN between two sites without any Layer3 on ISP side.
How to: - understand what kind of connection this will be? - is this connection is fine for customer? - identify if this kind of connection will be fine for converge network (voice+data) ? - what should I ask to ISP to clarify details?
I have windows vista, and forgot my network password. I reset my router to factory settings by pushing the reset button on the back.I tried reconfiguring the router from the network icon, but at the end of the process it says it cannot configure my router.I lost my internet service in the process
I just bought a Linksys E4500. I would like some support to configure the settings regarding the 5 Ghz Bandwidth.I need to fill out the cells for Server Radius IP and port.Which are the best setting for this section?
After a successful firmware update to my router I can’t configure wireless settings because the .htm page stays blank if I back the page it comes back to setup page but any config page shows blank with no error message. I’m on a win8 64 iexplorer 10, also tried on a win7 32 IE 8,9,10.
Do you know when will be possible to manual configure ipv6 settings? I have all parameters from my ISP but the settings on the router are only automatic and 6rd. Is it possible to enable this in future firmwares?
i recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
We have installed the Cisco Prime LMS 4.1 in our production environment. We have configured SMTP settings, but unable to find where we can configure username and password for SMTP authentication. It's only giving a option to enter email address without any authentication parameters.
I have a situation, where I dont need email and where is no SMTP server in this network, but I need CCO-access for EoX/PSIRT from LMS. Because both settings are in the same menu and LMS4.0.1 does real TCP:25 checking for given SMTP-server before can apply, I cant save my CCO-credentials. What can I do?
I installed the Cisco LMS 4.0.1 (test mode), and monitoring services of the switches (data collection and information system) are working.
But when I need to apply some configuration via CiscoView settings are not applied.
The following message is displayed when I try to apply some configuration on an interface of any one switch.
"Message Timeout on 172.20.1.10. This error could be due to lack of access to the host, invalid SNMP credentials, or a busy device. To correct the problem, do one of the following:
- Verify access to the host.
- Check the SNMP credentials.
- Increase the timeout value through the preference options on the chassis view."
I've checked the credentials and SNMP communities, the problem continues.
I am using lms 3.2.where I have added devices manually.Because discovery settings the device are taking some random ip updating the display and hostname.
The Cisco VPN client is disconnected after 4 hours of inactivity. Is there a setting on the ASA that would timeout after 4 hours? I want to disable this setting. I am running IOS 8.2(4).
I'm looking for a good router, home or even Small Business, with good QoS settings. Right now I have the Linksys E3000, but I think I could do better. I want to prioritize VoIP traffic.
I have posted on other sites as well everyone says to use Qos but they dont tell me how.I would just like to be able to limit my brothers bandwidth not just programs. We both use laptops, I use Ethernet, he uses wifi. My router does not have a wifi speed setting. I have tried multiple times to try and set up Qos on my own but it has not worked at all
I'm trying to automate our rollout process with kiwi cat tools. I want to copy a file via TFTP or FTP: Cisco tftp menu knows the latest ip address which it was connected to.
Nothing happens when clicking the SAVE button after making changes on the VLAN Membership screen when using IE9, but it work fine with IE8. Any problems using IE9 during configuration?
I seem to have managed to set a 2960 to 230400 baud in the boot loader. Is there anyway to reset the variables in the boot loader? Maybe a set of pins to short? I can't access the console port reguardless of what I set the rate too. I've tried both the USB console cable and a USB to serial. Is there anything I can do short of an RMA?
I just recieved a WAP4410N and managed to log in to the web interface. It is not allowing me to change many settings. I try to change the wireless network mode and click on save and it goes back to disabled again.
P.S. I have just upgraded the firmware to 2.0.3.3 and tried to set it back to the factory defaults. neither worked.
I have purchased two sets of WAP4410N and i need this to connect as wireless bridge to use our external office users(1 or Max 2) which is just beside our office building to surf our internet and retrieve data from our main server.