Cisco WAN :: C7200p Which Of These Two Ios Is Better For Gateway Internet Router
Jul 14, 2012c7200p which one is suitable for bgp and internet traffic and qos ?my router is 7206.
View 2 Replies
ADVERTISEMENT
Linksys Wired Router :: RV082 Gateway To Gateway VPN Not Connecting?
Jan 24, 2012I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
Linksys Wired Router :: VPN Gateway To Gateway With Two RV042 Constantly
Jul 11, 2012My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies View RelatedLinksys Wired Router :: RV042 Gateway To Gateway Connection?
Feb 8, 2011we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies View RelatedLinksys Wired Router :: RV042 - Gateway To Gateway VPN Connection
Mar 22, 2011I have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
Linksys Wired Router :: RV082 Gateway 2 Gateway VPN Can't Ping
Jul 26, 2012We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
Linksys Wired Router :: RV042 / Setup A Vpn Gateway To Gateway
Apr 6, 2013i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies View RelatedLinksys Wired Router :: RV0XX Gateway To Gateway VPN?
Mar 6, 2011I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
Cisco :: OSPF - Router As A Gateway And Has An Own Gateway?
Jan 29, 2013Can a router using OSPF propagate that he is a router with default-information originate... at the same time when he got an own gateway of last resort to an IP-adress? If so, how? I can't get it to work.
View 8 Replies View RelatedHome Network :: Can Ping Gateway But Not Router And Slow Internet
Feb 21, 2011A while ago internet access was slowed right down for an hour or so. I have a phone line that comes into the house and then into gateway (10.0.0.2) then ethernet from that to linksys wifi router (192.168.1.1). So I did the following ping and repeated what you see below a few times to see that these results were broadly consistent, which was the case. One other person is connected to linksys via ethernet cord and they might have been on at the time. Questions are.... are these results consistent with contention caused by other user on the linksys? and why can I ping gateway but not the router? That makes no sense to me! I am not annoyed with the other person if he is hogging the network...I like him. I just wonder whats going on. When the internet works results from pinging are all as one would expect
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsNASA>ping 192.168.1.1
[Code].....
Linksys Wireless Router :: WRT100 - Internet Gateway Connection Disabled
Aug 3, 2011I had to restore my laptop yesterday and i reset my router (WRT100). I ran all the Microsoft updates, but I didn't do anything with the router other than going to the Linksys site to try to make it secure. My computer seems to be recognizing the router (although it is still saying it is an unsecured connection) but I cannot get on the internet. The problem seems to be when I pull up the Network Connections window the "Internet Gateway-Internet Connection" is showing disabled. I cannot enable.Everytime I try, it says "connecting...Connection failed!". I can plug the ethernet from the modem to the computer and it works and the "Internet Gateway" doesn't appear, but when I try through the router it does. I want to set up the router because I have two computers that need internet access.
Three connections are listed--Wireless Access, LAN, and 1394 Connection. All are listed as connected, firewalled.The second computer is also giving me a problem. There is the wireless issue, but when I connect the ethernet from the computer directly to the modem I am asked if I want to connect via Broadband and am asked for a username/password. There is no username/password. I've contacted my ISP (Cox cable) and confimred there is no password.
Linksys Wired Router :: RV042 - Can't Access Internet Or Ping Gateway
Jan 4, 2011I am using the default configuration at this point. I just connected 1 computer using the default IP with DHCP on the RV042 router. 192.168.1.0/255.255.255.0.I connect my wildblue satalite modem using a static IP address 75.106.203.xxx / 255.255.252.0 I can ping the RV042 router and the static IP address of the wildblue router but I can't ping the gateway on the wildblue side. Either from the PC or the Router diag tools.
View 1 Replies View RelatedLinksys Wireless Router :: E1200 Do Not Have Internet Access As Default Gateway
Nov 11, 2011I have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies View RelatedLAN Connection But No Internet - Internet Gateway Disabled?
Nov 6, 2011I have a desktop computer that I have used for years and it has always worked just fine. We have AT&T (DSL, not cable) and it used to connect just fine but then I moved out, left everything plugged in exactly as it was and when I came back it wouldn't connect.It connects to the LAN but not to the internet. When I go in cmd to type ipconfig the DNS suffix is blank on that computer but says gateway.2wire.net on my wireless laptop. I eventually disabled UPnP on it because that's what alot of people were saying fixed the problem but it didn't fix anything. All it did was make the Internet Gateway Connection box disappear.Originally it was plugged in like so: Cable from wall > Cable Box > PC Now it is hooked up like this: Data cable from wall > DSL > Router > PC It stopped working BEFORE it was switched to DSL so that isn't the problem The DSL we have is "AT&T 2701HG-B 2Wire Wireless Gateway DSL Router Modem" and the Router it is plugged into that goes to my PC is a Linksys Wireless Router Model WRT54GS The PC is Windows XP Home, SP2?
View 19 Replies View RelatedCisco Routers :: RV082 Gateway To Gateway VPN Not Resolving Remote DynDns
Feb 14, 2013I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
Cisco Routers :: How To Manage Port 80 Hosts Via Gateway To Gateway VPN (rv220w)
Aug 30, 2012I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...
View 0 Replies View RelatedCisco Routers :: RV220W Gateway-to-Gateway Inter VLAN Routing?
Jul 6, 2012I picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
'TECHNICAL' SPECS
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
[URL]
Cisco Security :: Rv042 Vpn Openswan Gateway To Gateway Linux Unbutu
Sep 13, 2012config setup
protostack=netkey
klipsdebug=none
[Code]....
Cisco Routers :: RVS4000 To Use A Gateway To Gateway IPSec Tunnel
Oct 17, 2011Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?
View 1 Replies View RelatedCisco Routers :: RV042 Gateway To Gateway Tunnels Not Reconnecting
Apr 11, 2013I have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.
View 2 Replies View RelatedCisco Routers :: RV016 Gateway To Gateway RV082 Won't Connect
Mar 9, 2012New hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
Cisco Routers :: Getting VPN Gateway To Gateway With NAT For Multiple Subnets / RV082?
Feb 11, 2012I have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc). I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity.
Routing does behave as advertised, where all traffic does go to the main office. However, the 192.168.1.0 subnet in the branch office does not get internet connectivity. I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet. Is there a way to configure the RV082 router to provide NAT for all subnets?
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets? Can the RV082 be used as part of the final solution or are my RV082s a wasted expenditure?
Following is the configuration that I'd implemented, (real IP and IKE keys are bogus).
Gateway To Gateway
Remote Main Office
Add a New Tunnel
Tunnel No. 1 2
Tunnel Name : n1-2122012_n2-1282012 n1-2122012_n2-1282012
Interface : WAN1 WAN1
[code].....
Cisco Routers :: RV8082 Setup A VPN Tunnel With Gateway-to-Gateway
Apr 8, 2012I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway. One location is a static IP Address. The other location is a dynamic IP address.
View 2 Replies View RelatedCisco VPN :: WRVS4400N VPN IPsec Gateway To Gateway Setup?
Jan 29, 2012Just bought 3 WRVS4400N, I wanted to setup gateway to gateway VPN. I followed the instructions on the WRVS4400N admin guide and VPN does not connect. I also downloaded the VPN setup wizard and that also did get the gateway connected. Everything seems to be correct. Do I have to enable anything else? Firewall setting?
Below is my config.
IPSec VPN Tunnel: Enabled
Tunnel Name: TUN01
Local Security gateway: IP only
WAN1 IP: 192.168.100.1
SUBNET: 255.255.255.0
Local Security type: subnet
LOCAL IP: 10.10.10.1
SUBNET: 255.255.255.0
[code]....
Cisco Routers :: Gateway To Gateway VPN Between RV110W And RV042G?
Mar 19, 2013I am trying to set up a gateway to gateway VPN connection between a RV042G (central site) and a RV110W (newest firmware) which is used for presentation purposes on various customer's sites. The RV042G has a static IP. The RV110W has different IPs, depending on where it is used.
Basic VPN settings are clear to me (we have another VPN between two RV042G with static IPs). I set up the VPN connection on the RV042G wth the following settings for "Remote Group Setup":
Remote Security Gateway Type : IP + Domain Name (FQDN) Authentication IP by DNS resolved: mydomain.no-ip.org Domain Name: router12345
The value "router12345" is what I have configured in the RV110W as "Host name" in the network settings.
This configuration does not work so I am obviously doing something wrong. Do I have to use "router12345.mydomain.local" instead if I configured "mydomain.local" as the domain name in the RV110Ws network settings? For my tests the RV110W has a WAN-IP of 192.168.178.100 because it is located behind a DSL-Router. The external IP of this DSL-router is 178.0.x.x. The resolved IP from mydomain.no-ip-org is 192.168.178.100 but when I look in the RV042G log I see the requests coming withg the external IP (178.0.x.x). Is this the problem? The last message I see in the log is "no connection has been authorized with policy=PSK".
Or can I use "IP + Email Address (USER FQDN) Authentication" instead (where can I enter this email address in the RV110W?). Or do I have to use "Dynamic IP"?
No Internet Or Default Gateway
May 8, 2011Basically, I'm using a broadband modem, which appears to be connecting fine, with all the required lights being on. My ISP says that, from their end, everything is perfect. Even my laptop shows Local Area Network as connected.However, for some reason, I am not able to access the internet. I was able to use it till last evening, but suddenly the internet stopped working. On Google Chrome, it says that there is no DNS or something.Subsequently, when I tried to access my modem settings, it shows as 'webpage not available'. I then noticed that there is no default gateway! I was able to access it the day before, but now I can't.
View 10 Replies View RelatedWireless :: Gateway Will Not Connect To The Internet?
Oct 19, 2011I have a gateway with windows 7 and was working fine and a couple of weeks ago it will no longer connect to the internet. I have always used the wifi connection. The wifi signal is a orange computer and on my other computer when it is working it is typically green, so I am not sure what this orange color means, if anything.
View 4 Replies View RelatedGateway Laptop Won't Connect To Internet
Mar 13, 2011Laptop has been connecting to internet for years. Originally using wireless Linksys router but wireless card in laptop stopped working. Have been connecting via Ethernet connection for over a year. All of a sudden, cannot connect to internet via Ethernet connection. Laptop connects fine using wireless mobile card (Verizon) with 75.x.x.x address.Using same Ethernet connection,another laptop connects fine (69.x.x.x address)Network status on "broken" laptop shows "Unidentified Network Access: Local Only Ethernet adapter has 169.x.x.x address when connected to cable modem (Roadrunner) with no default gateway.Tried to release/renew IP but get message "The requested operation requires elevation." I am running under admin account.
Sys Info:
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft� Windows Vista� Home Premium , 32 bit
Processor: Intel(R) Pentium(R) Dual CPU T2330 @ 1.60GHz, x64 Family 6 Model 15 Stepping 13
Processor Count: 2
RAM: 2037 Mb
Graphics Card: Mobile Intel(R) 965 Express Chipset Family, 448 Mb
Hard Drives: C: Total - 227412 MB, Free - 101980 MB; D: Total - 11060 MB, Free - 4533 MB;
Motherboard: Gateway, , Rev1.91.18, V7CBMYY60722CE706X
Antivirus: None
Repeated Disconnections From Internet Gateway?
Aug 20, 2011i have problem in connecting internet.Repeatedly it is disconnected from internet gateway.
View 5 Replies View RelatedGateway To Internet With Firewall And Filtering?
Jun 29, 2011I was just wondering if it possable if I could make a server with URL Filtering, Firewall, and a login system.So, when users want to use the internet they are required to login before they do. Is there a program out there?
View 2 Replies View RelatedGateway Notebook Won't Connect To Internet
Jan 13, 2012wMy Gateway notebook won't connect to the internet even when directly connected to the router. When I ran the diagnostic, it said to reset the modem. When I went into Device Manager, there was no modem listed. I did reset the wireless adapter- to no avail
View 1 Replies View RelatedCisco WAN :: CME 2911 Load Balancing For Two Internet Gateway?
Feb 18, 2013I have a customer he has two internet gateway connected through fast-Ethernet, and he wants to load balancing between two internet gateway.
How can I make load balancing for two gateway
Cisco VPN :: RV042G / 1721 - Gateway To Gateway VPN
Mar 23, 2013I try to install a Gateway to Gateway VPN between a RV042G router (LAN1) and a 1721 router (LAN2). The VPN is connected. I can ping the devices from a LAN to the other in the two way.
But otherwise I can't access to the devices of LAN2 from LAN1 like with telnet, HTTP, mstsc, ....
And it is OK to access to the devices of LAN1 from LAN2....
Normally I access to all the resources of LAN2 with the Cisco VPN Client but i try to change it with this router. The firewalls are off on all the computers I look.