I'm trying out the RV120W wireless router with the latest firmware. I have two APs set up with different schedules. However, the router fails to enable the APs as scheduled and I have to cycle the power to get the APs going again.
View 1 RepliesI use CiscoWorks LMS 4.0.1.
I planned a discovery of devices for some time, but if I change the parameters of discovery (adding a seed device) in "Discovery Settings Summary", this change does not apply in the scheduled task.
If I change the settings in the scheduled task, the changes do not apply in "Discovery Settings Summary". We must change the settings 2 times.
DIR600 doesn't allow me to enable wireless MAC filtering when I setup DIR600 as access point. (I connected DIR600 (access point) to my another room's router.)
View 1 Replies View RelatedMy router (WRT54GH) doesn't seem to be enabling the wi-fi network. Non of my devices are able to detect the wireless network.
View 3 Replies View RelatedI start my pc i get 2 local area connections instead of 1 and because of this my internet does not work unless i disable and enable again the network .After enabling only 1 network shows and i can connect to internet.It may be because i replaced my motherboard even tho i uninstalled the drivers?
View 1 Replies View RelatedI recently got a Motorola NVG510 (from AT&T, they changed our internet plan and sent a new router) and since then I've had problems with Skype. I think I've narrowed the problem down to there being no upnp on this router to enable, and Skype doesn't like that.So, is there any way I can make this option available, or some other way to 'simulate' upnp so Skype will play nice? I read somewhere else that "IP Passthrough" may be an option, but I'm unsure about that.
View 1 Replies View RelatedA few weeks ago I noticed that at 9:00am sharp every morning my internet access dropped, and would come back up four minutes later.
The router is connected to a DSL-526B in bridge mode. My first thought was that the modem was playing up, so I factory reset it and reconfigured it.
I checked my ACLS and didn't see any rules that started or ended at 9:00 am so I just lived with it for a week or so until it got so annoying I contacted my ISP to see if they were resetting anything at 9am.
By accident, I saw that my wireless radio was being enabled aat 9:00am, as it had been for the last 2 years, when I first bought the router. But this problem has only started a few weeks ago.
So I changed the wireless schedule to see if that was really the cause for the reset, and sure enough, whatever time I changed the wireless schedule to, the router rebooted at that time.
I've also factory reset the router; twice; the first time I saved/restored my configuration, the second time I recreated all configuration from scratch.
why enabling the wireless radio resets the router, and why disabling it doesn't, and how to correct this behaviour?
I am running an E3000 with Firmware - 1.0.04.
I would like to schedule my boys ipods to be on the network from 2:00pm to 4:00pm each day.
Running the Cisco connect software it would appear I can schedule from 2pm until the next morning but not a 2 hour window in the same afternoon.
Looking through other posts I see earlier software where this can maintained through the Router firmware but with 1.0.04 I seem to have to use Cisco Connect.
So how can this be done with my current configuration ?
How can view the scheduled archiving job in lms 3.1 ?
View 1 Replies View RelatedThough other logs are being received through the email.
View 1 Replies View Relatedcreate a scheduled task in LMS. In this task I would like to regularly check time on all network devices in LMS and generate a rapport about this that would be sent to e-mail. All network devices have the same NTP server. How can I create this task? LMS version is 3.2 SP1.
View 4 Replies View RelatedUsually the configuration files are fetched once every week. Lately, the Scheduled Config collection job is failing for all the devices. I have tried to “sync Archive” from LMS 3.2 on some devices but nothing happens. The switches out there are C3750, 2960, 2950, 3550, 3650 and some routers.The server is Win Ser 2003.
[URL]
Friend of mine has a setup out in the sticks, currently with two ISPs: Hughesnet satellite, and a line-of-sight WiFi provider; they're also getting a cel tower within range soon and he's looking at adding an HSPA/LTE connection via that as well.the first gives him a static IP and ridiculous speed and bandwidth at night... but far less speed and a painfully low bandwidth cap during the day (you go over, you pay through the nose).
The second gives lots of bandwidth but poor speeds (difficult to even watch a YouTube video) and a constantly-changing dynamic IP.The third, once implemented, will give him good speeds and decent bandwidth (I believe up to 10GB/mo) but again, will get spendy if he goes over that limit.Right now, I've got him set up with both routers plugged into the same network, multi-homed the NICs on his machines (192.168.0.* for Hughes, 192.168.1.* for LOS) and a little script on each computer that will change the default gateway to let him select which ISP he wants to use... however, it's going to get trickier with a third, and will make it even tougher to keep track of the bandwidth used on each one... especially with multiple computers, a DVR, and two users.
So I'm looking for some way to automate all this... something that will, say, use the HSPA feed most of the time for his whole home network, switch to LOS if it gets near the cap, and switch everything over to the satellite automatically during "unlimited" hours. Again, I'm not opposed to setting up something PC-based with the appropriate software, although for my own sanity, it would really need to be Windows-based (I'm way below n00b with Linux).
I'm trying to schedule a 90 second capture every 20 minutes to coincide with a process I have running. I have created a batch fun to run tshark.exe with the command to stop after 90 seconds, and an output file (-w). This all works, my challenge is that the next time it runs it overwrites the previous file. Is it possible to make tshark timestamp the filename? or is there something clever someone can recommend with a batch file to copy last version somewhere else and rename, so that I can have the process running constantly.
View 3 Replies View RelatedWe're since long having a problem with a DSL internet connection. The connection goes down periodically, for short times, and when performing speed tests, the connection speed varies and is usually lower (0.7 Mbit/s) than what the ISP promises (1.5-2 Mbit/s). Moreover, what modem is being used seems to have an effect.Now, I want to trouble-shoot this and get some hard facts on the behaviour of the connection. I would like to do repeated speed tests over say 24 h or so. They should be done every 3 min or so (to catch short glitches).
My question is: what software tool can I use for this? I have been searching the internet for hours, downloading a handful of applications, without finding anything that I could use. There are loads of applications that log and graph the current upload and download speeds, but that's something else - I need a tool that downloads/uploads files from/to a server, in intervals specified by me (3 min), logging the result and presenting it graphically.
So I have bought myself a DCS-2121 with firmware 1.05, 4630. Everything works fine except that the camera does not seem to adhere my settings on the snapshots page. At average, it seems that only one image is sent to my FTP-server regardless of the interval parameters.
View 2 Replies View Relatedmy DCS-2121 :
The scheduled recording or scheduled snapshots is not working. I am running the camera standalone and using the web based configuration, storing the images or avi's on a ftp or samba server.
No matter what i specify, it records when triggered (by motion in my setup). All the other settings like, samba, ftp, video, motion detection, and so on is working fine - but I can't configure it to only record like between 10-16 every day. It records all the time - no matter what I select and what I enter in the schedule scheme.
My company just purchased this router for my home office for the purpose of connecting to multiple office locations.I put this router on my network at about 6pm, several machines connected to it and and were given IPs.About 5 hours later I powered up another machine and it would not get an IP address until I rebooted the router.This morning at about 5am I rebooted my SIP phone and it would not grab an IP either, not until I rebooted the router.
View 3 Replies View RelatedI've some troubles connecting my PS3 to my RV120W.Both router and PS3 have latest firmwares. They are connected wireless (distance is about 10 mt, signal is good).PS3 ip is in DMZ (connection doesn't work with only Upnp), and ip fragmentation is enabled.Everything seems to work (NAT type 2), but downloading on PS3 is extremely slow. My ADSL is a 6Mb, download speed on PS3 seems like more than ten times lower (I don't know how to test it..). Plus, downloading a 100 MB patch is almost impossile, cause sooner or later I get an error and i have to restart.Two of my PCs are connected wireless, so I guess wi-fi is not the problem.
View 3 Replies View RelatedCan the rv120W be configured as a wireless bridge? We have a need to configure a vpn connection to a remote building but will need to connect the router via an existing wireless network.
View 4 Replies View Relatedif you bring your new firmware, please verify the small bug in 'Time Settings': If you choose CET (GMT +1h) AND enable 'daylights saving time' the time goes back 6 hours instead of forward 1 hour.Firmware of RV120W: 1.0.1.3
I'm surprised that CISCO needs such a long time to solve such an issue... I thought I bought the new router from a leading network provider
I just recently replaced an older linksys pre-N router with a RV 120W. I thought this would be a good choice as a more professional router. I installed this router last week and things seemed to be working normally for web browsing, though I was receiving more incomplete pages and broken graphics. Yesterday, I tried to watch a youtube video a friend had sent me and it would not play. I tried several other videos from youtube and other sources with the same result: stalled videos, partial played videos followed by a spinning wheel. It was late, so I figured something was going on with Comcast and went to sleep. This morning, I was trying to download Anti-virus updates. The updates failed multiple times. I then tried some videos again with the same results. I tried downloading .ZIP files from several sources, and while the file completely downloaded, each and every file was corrupted and unusable. Before I called Comcast to complain about my Internet being flaky, I unplugged the Comcast Arris TM502G device from the Cisco router and plugged it directly into my computer fully expecting the problem to persist, but the problem immediately dissapeared. The immediate evidence is that the problem lays with the Cisco Router. It appears that I can't make any changes on the Comcast device as it has a comcast public IP address and does not seem to have any web or telnet interface to change the settings.
- On the Cisco router, I disabled every non-essential service: VLAN, QOS (bandwidth profiles), IPV6, etc
- I updated the FW to the newest version the day I installed the router
- I power cycled the router
- I power cycled the comcast device
I need to resolve this issue as soon as possible, but I'm not sure what to try next, and I'm confused about my support options after trying to navigate Cicso's support pages. It offers live chat, e-mail support, etc, but everything I go into requires a contract number.
how can i solve this error:
Tue Nov 27 10:55:40 2012(CET) [rv120w][Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK
Tue Nov 27 10:55:40 2012(CET) [rv120w][Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK
Tue Nov 27 10:55:40 2012(CET) [rv120w][Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK
Tue Nov 27 10:55:40 2012(CET) [rv120w][Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK
Tue Nov 27 10:55:45 2012(CET) [rv120w][Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK
[code]....
i have a wireless device and every 1 hours the connection drops and i must reboot the device
I want to know if it is possible to put the cisco small business router rv120w into bridge mode so that I can connect it to a linksys e2500 access point. Is this even possible or am I wasting my time?I have 4 devices connected to the cisco router that I want to be able to bridge to the linksys e2500 which has the internet connection.
View 1 Replies View RelatedI would like to set up a site to site VNP connection between 2 RV120W routers, preferably via IPsec.
The problem is that I would like/have to use a 4G modem router (model TINY) which connects to internet in front of the RV120W (on the local side)
I have no problem with that on the remote site that RV120 connects directly to internet via a public IP address on the WAN port.
Local network 192.168.1/24-----RV120W----192.168.100.1—Tiny---Public IP--------INTERNET
INTERNET--------PublicIP—RV120W—Remote local network 192.168.2/24
I have established a site-to-site VPN from my head office to a remote location. WRVS4400N router is used in the head office and it is in 10.0.1.0/25 private range. RV120W is used in the remote location and its private range is 192.168.0.0/25. We are able to ping and RDP to the head office from the remote location, but unable to do viceversa. A comcast router is also placed before the WRVS440N router at the head office. I need to get communication to both sides through the established site-to-site VPN.
View 1 Replies View RelatedI've a RV120W Cisco ROUTER with last firmware released and I am not able to setup Wake On Lan: It works fine just switched off PC but after some minute (5/10) magic packet don't work. Router forgets address of PC ?
I've set-up Static DHCP with IP and MAC address of PC ?I've setup port forwarding in firewall menu?This setup is OK becuse for few minutes WoL works... but after some time it stops.
There is any setting to make RV120W managing WoL properly.
I've a RV120W with the last firmware version (june 2011), i want to create two vpn tunnel:
- Professional: lan routing all packet for the 192.168.0.0/24 to the first VPN tunnel
- Other: all other address IP destination to a second VPN tunnel
The first tunnel (professional) is ok but what rules can i use to configure the second ?
What is the default login/pass of cisco rv120w for ssh access ?
View 1 Replies View RelatedUpgraded to 1.0.2.6 and all of a sudden SIP devices working over the VPN no longer work. Downgrade to 1.0.1.3 and they work again. My guess is that some ports are blocked over the VPN in 1.0.2.6
I thought the general idea was that firmware ugrades fixed bugs rather than introducing them.
Suggestion for Cisco:- Zip the firmware image downloads, or else have an upgrade process that includes a CRC check, that way at least the poor punter will have an indication if they have been corrupted. I had a subtle memory problem that was corrupting some files. The firmware upload appeared to complete properly and you could log on OK but some of the menu choices resulted in a hang with the "Please wait... the page is being loaded" message. Careful checking of file sizes revealed that the file I was uploading into the router was a few hundred bytes different in size to the one on the website, must have been corrupted during the download. But the upload proceeded normally with no indication of any error. It's a pretty basic safeguard that should be in there as a matter of course with the router performing a CRC check and showing an error if it fails.
I had WRT54G2 and recently switched to an RV120W. I have an Internet accessible camera system connected to my router. Before, this worked fine... there is a dns service (DynDNS.com) that is configured as part of the camera setup. I would then just enter [URL] and I would connect to the cameras. I install the new router (RV120W) and I can no longer connect to the cameras. I do not recall any configuring that I had to perform on the old router.
why the RV120W isn't letting me get to the cameras?
Rx:, recently I have perchase 2 RV120W routers thinking that it must be very easy to setup the site to site vpn. i cannot get my remore office to link to my main office and vice verser.
Scenaro
- I'm using 2 RV120W routers for each site.
- Site A using a subnet of 192.168.10.0 mask 255.255.255.0
- Site B using a subnet of 192.168.11.0 mask 255.255.255.0
I have setup the VPN using the wizard and I got site to site tunnels connected and show as 1/1 Connected (1 user) in the status he IPsec connection status show
--Policy Name: VPNA
--Endpoint : public IP address from my ISP 203.117.222.221
--Packets Tx:145 Rx:0 and Kbytes shows Tx: 29.55 Rx:0
Q1 why I cannot use dynamic DNS naming in the policy setting ? eg: aaa.dyndns.org, I have to use the ip address instead eg: 203.117.222.221
Q2. I cannot connect from Site A to Site B , I can't even do a ping to 192.168.11.1 from Site A. even though it show the Site to site tunnel is coonected.
I've just set up an IPSec VPN between 2 x RV120W which are both behind other router. Here's what we have :
RV120W #1 (192.168.1.254) --- (192.168.1.1) Office Router #1 (PUBLIC IP) --- (((Internet))) --- (PUBLIC IP) Office Router #2 (192.168.2.1) --- RV120W #2 (192.168.2.254)
It works great, tunnel is UP.
[Code]....