I bought a Synology DS411 slim NAS which I want to access remotely. I made a DNS and did portforward in my router (Cisco by Linksys WRT160N v2. The problem is I am part of a bigger scientists network where all ports are closed so it wont work. I even tried installing a OpenVPN server on the NAS and then connect though that but with no luck.
View 3 RepliesMy Xbox can't connect to my network yet my dad's and step bros ps3 connects fine, and all the laptops in the house too
View 1 Replies View RelatedWe're just bought a Netgear WNR2000V3 router and everything is working great, except for our XBox Slim......We can't connect very often and the only way I can get a connection is by disabling all other wireless connections. (Wii, IPod Touch, IMac and Acer Aspire Laptop) My main computer is the IMac.
View 1 Replies View RelatedI've been searching and searching the internet and I have never found a CERTAIN answer for if the linksys wrt160n v3 router will work for the ps3 or not. I want to know for sure if it will work because I know that is it sbackwords compatible with g/b/a networks but I am a newby at this stuff.
View 2 Replies View RelatedAs a temp work around I have two SSID now, one for everything else running WPA2 and one for xbox running WPA. The xbox seems to not like the router on WPA2 and though this would make one think, oh its your xbox, thats not always the case with devices. Some just may happen to want to use a feature the device doesn't support correctly and other devices are able to work around it while ones not so I cant for sure blame on xbox.
View 1 Replies View RelatedI've got a Centrino Advanced-N 6205 for Desktop wireless card and I'm trying to use the Intel My WiFi hotspot feature to connect my Xbox 360 Slim. The SSID shows up in the Xbox's networking settings, but after I enter the WPA passkey it fails to connect.
View 2 Replies View RelatedKinda narrowed it down to the ds1512+ to replace a whs2011 (that was made from a hp media server). No rush. Just upgrading. What is the refresh cycle? I can wait until the new servers come out.
I'm not smart or dedicated enough to build a box from scratch. I just want it to work neatly.
Having a hard time hosting my email service on my DS212J. To be I honest, I have no idea where to start.
Info:
IP Address using Synology DDNS: example.synology.me
Domain: example.ca
I have a Synology DS 710.And I would like to set it up so i can access it from any where within my network. But also be able to access remotely either by my Iphone and my MAcbook pro.
I tried setting up a VPN but I find that I would get the basic setup done on my 710 and my mac. but my mac can not connect. Also find that I would need a password but not sure where I would create/find a password.
is it possible to setup 3 x xbox 360's in a home network, 1 is mine, connected to live, the other 2 are for the kids but i just want to setup local network gaming with the kids but also so they cannot connect to live account as they still young. i'm looking to run game on mine and stream / share a multiplayer game with the kids but restrict their internet access?
View 2 Replies View RelatedI am trying to set up a Synology VPN server thru a cisco RV220W and cannot get a windows 7 VPN client to connect to it. Access rule was created on RV220W to port forward 1723 and also made sure the same port was forwarded on the built in router on the Synology NAS box, running DSM4.1 and made sure VPN server was up and running. IP address of synology NAS is 192.168.1.250, mask of 255.255.255.0. DNSgateway is 192.168.1.1. Only running PPTP at this time.
When I run the windows 7 VPN client, I try to connect to the external internet addres:1723, make surePPTP is the only protocol and use a DNS of 192.168.1.1. When I try connect, I get an 868 error which says "error 868: The remote connection was not made because the name of the remote access server could not resolve."
When I try to ping port 1723, I do not get a response which leads me to believe that the issue is the router and not the NAS box. HTTP, HTTPS and FTP ports work fine.
I've been using the Dir-655 for 2 or 3 years with my old Xbox 360 and an external G wireless adapter. Everything was working perfectly until I got the dreaded Red Rings Of Death the other day. I replaced the Xbox with a new Slim version with built in N capable network adapter.
After more than 10 hours of trying a variety of "fixes" I found from MS and in this forum, I am still at square 1.
Hardware Version : A3
Firmware Version : 1.32NA (this is listed as Live compatible by Microsoft)
802.11 Mode : Tried N only, G only and mixed 802.11n and 802.11g
Enable Auto Channel Scan : Checked
Transmission Rate : Best (automatic)
Channel Width : Auto 20/40
Visibility Status : Visible
Security Mode : WPA-Personal Also tried WEP
WPA Mode : Auto (WPA or WPA2) Also tried WEP
Cipher Type : TKOP and AES
I tried assigning an IP manually from the Xbox. But, no matter what I do, the router will not accept it. It is especially frustrating that the Xbox is visible to the unit. It simply will not assign an IP to it under any circumstance.
If you read the sales hype promoting the Dir-655, you will see a lot of nonsense about it being great for gaming. Given that, you'd think a simple solution would have been found and posted for this issue by now. Surely, end users shouldn't be trying 100 different possible "fixes", none of which work, at this late stage of the firmware upgrades. If I sound a tad fed up, it's because I am. After the expense of the new Xbox, it appears I now have to junk my router too.
Here is the status screen taken when it was in mixed mode. Changing it to 'G Only' didn't make any difference:
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 2.1 v000c.0 Build 130415 Rel.34164n
ISP : plusnet
I have setup 2 vpn tunnels from my TD-W8970 to places that use TD-8960N (Firmware Version: 1.4.0 Build 110921 Rel.17774n Hardware Version: TD-W8960N v3 0x00000002 )and I can ping and connect to any ip used at their end but they can only ping 192.168.1.1 which is my router and not 192.168.1.104 which is my Synology DS212J that they need to access.
Both tunnels are similarly configured:
Tunnel 1 on my TD-W8970
IPSec Connection Name: Tony1
Remote IPSec Gateway Address(URL): 89.240.xx.xx
Tunnel access from local IP addresses: Subnet
IP Address for VPN: 192.168.1.0
IP Subnetmask:255.255.255.0
[URL]
I have a Server 2008 server and a Synology DS1511+ Nas.The goal is to make an iSCSI connection from the Synology to the Server 2008 server. However, I am having an issue. I set this all up two weeks ago. For two weeks it was all running fine. Now, my iSCSI drive is dropping daily. And everytime I go into the iSCSI initiator and click anything, the server still allows me to do some things, but it basically locks up. I can't restart, services stop responding, etc... The only was I can break it out of that is a hard reset. Why iSCSI initiator keeps taking down my entire server to the point of hard restart? Once this is solved, I bet the iSCSI dropping daily will be solved as well. I have already talked with Synology, the log is producing nothing and they are suspicious that it has been running fine the past two weeks. Windows update is off (I manually do it during scheduled maintenance), and there is no av or firewall running, so rule those out.
View 8 Replies View RelatedI've just bought a Synology DiskStation DS412+ and put 2 x 3TB Western Digital Red drives in it, set up in RAID 0. It's currently plugged in to my gigabit Netgear switch.I created a user with full permissions on the NAS, created a share, mapped a drive on my Windows 7 PC (also gigabit ethernet) and tried copying some files, but I'm getting painfully slow transfer speeds (< 40KB/s - yes, kilobytes, it's not a typo!
Does anyone have any ideas why it'd be so slow? There's loads of reports online of people getting > 80MB/s from this NAS.
I've copied files from this PC to my MacBook Pro in the past and got decent enough speeds so it shouldn't be an issue with the NIC on this PC, or (hopefully) the Netgear switch it's going through.
My friend has had constant issues with his wireless network using his dated Linksys router. So he finally decided to upgrade to the Netgear N750. It's a dual band router that simultaneously broadcasts 2.4 and 5 GHz bands. He setup the 2.4 band for the laptops and mobile devices to access, and the 5 band just for gaming on his xbox 360 Slim. He immediately ran into a problem. The 360 slim's built-in wireless card only picks up 2.4 GHz frequencies. To remedy this, he purchased Microsoft's xbox 360 wireless-N adapter as it can pick up 5 GHz frequencies. However, there was no change after plugging the adapter into the 360 slim. His HP laptop can see the 5 GHz network just fine, so we know it's being broadcast. Could it be the xbox is out of range of the 5 GHz band? Is the adapter not functioning properly with the 360 slim?
View 2 Replies View RelatedI am looking to get a wireless card to share my wired desktop connection for my tablet, laptop and phone and xbox 360 slim. A wireless router would seem the obvious solution but the accommodation I have at uni charges £15.00 just to allow a router to be used.
View 1 Replies View RelatedI just bought a synology NAS ds212j . I updated to DSM4.0. I purchased 2 Seagate ST2000DM001 Barracuda 7200RPM 2 TB SATA 6 GB/s NCQ 64 MB Cache 3.5-Inch Internal Bare Drive
My e3200 has the latest 1.0.04 firmware I'm backing up via time machine(mac book pro) in MAC 10.7.4 which has a wireless N card.
in Utilities (activity monitor)I'm only getting 9 megabytes per second , why is it so slow? I feel like it's taking forever. e3200 says it does up to 300 megabytes per second. any possible settings causing this?
a backup of 202 gigs has been running for about 4 hours and still going
I have an ASA 5510 in a live environment. Up til a short while ago I could access this via the ASDM and ssh. However I can no longer connect to it via eithier. When I access It via SSH I get a disclaimer saying the following
*** You have entered a restricted zone! Authorized access only!!! Disconnect immediately if you are not authorized user! ***
It then cuts me off.
When I try to access the ASDM I get the following
The firewall is running all its services without a problem and I can ping the device without any issues. Also none of the config (to my knpowledge has been changed). I set up a console session and http server enable is still there with
http 192.168.200.0 255.255.255.0 inside
I have a PIX 501 that I used to be able to connect to just fine. Now I cannot get the PDM to come up Inside, Outside, Nothing. I am using the same(old) version of JAVA 1.4 that I have always used. I can Telnet etc.. just fine. The HTTP server is enabled and have granted access to from my IP's.
pixfirewall# show run: Saved:PIX Version 6.3(5)interface ethernet0 autointerface ethernet1 100fullnameif ethernet0 outside security0nameif ethernet1 inside security100enable password 8Ry2YjIyt7RRXU24 encryptedpasswd XXXXXXXX encryptedhostname pixfirewalldomain-name ciscopix.comclock timezone EST -5clock summer-time EDT recurringfixup protocol dns maximum-length 512fixup protocol ftp 21fixup protocol h323 h225 X0fixup protocol h323 ras X18-X19fixup protocol http 80fixup protocol rsh 514fixup protocol rtsp 554fixup protocol sip 5060fixup protocol sip udp 5060fixup protocol skinny 2000fixup protocol smtp 25fixup protocol sqlnet 1521fixup
[code]......
Why I can't contact 97.x.x.218 trough a remote desktop client from a remote WAN? On the LAN the RDS server (192.168.1.20) can be reached, that works fine. It seems the ASA firewall is causing the problem.
ASA Version 8.4(3)!hostname cisco-asaenable password cE8C encryptedpasswd 2KFQnb encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.253 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address [Code]...
Let me explain my current situation before asking my question:I have a Motorola Netopia7347-44 VDSL modem/router (with WiFi). The type of signal that I get from my ISP is analogue for phone, TV and intenet.This modem has an input for the Internet connection (dynamic IP address) and provides the IP addresses and connection for the other devices connected to it (via WiFi or cable), such as the TV over IP box, laptops, iPads and smart phonesI would like to implement content filtering on my WiFi network in order to avoid access to some websites, and my modem/router doesnt provide this feature (or at least I cant find it with my ISPs configuration) thought about using OpenDNS, but since I have a dynamic IP address and I cant install an updater on all the devices, then this solution didn work.
The next idea I have is getting a physical Firewall.Question: I am wondering if I can just connect the Intenet cable (that comes from the splitter between phone and Internet) to the Firewall, then I connect a RJ-45 cable from the firewall to my existing modem/router and should that be all (besides configuring content filtering on the firewall)?What should I take into account regarding the IP addresses? Should I enable the DHCP server in the firewall (I assume that most come with one), and disable the DHCP server in the modem?
Today, out of nowhere (no known system changes) I was unable to connect to a network server at my office. I always connect with a VPN first....and that went fine.Then - when I tried to map to a network drive, it wouldn't connect. I get error code 0x80070035.When I disable my AVG firewall, I'm able to connect perfectly.So, I'm guessing I have to create some type of rule for my firewall, but I have NO idea where to get the info with which to do so. I'm running Windows 7 (64B) and have AVG Internet Security 2011.
View 6 Replies View RelatedI'm using ASA 902, and I deploy any connect ssl only and no IPSec... It always open only connection if you start via browser, you cannot reconnect using installed software.
View 2 Replies View RelatedI'm building a dual firewall solution for exchange. Currently, I also have people connecting VPN to the PIX 515E.
Internet ==vpn== 5505 == LAN
Looking to set up
PIX515E ==dmz== Edge server == ASA 5505 == LAN
In a setup like this, which device should I have people connect VPN to? The pix will be the only device directly connected to the internet. Everything else will be natted.
I'm trying to access our ASA 5512-X via the Management port, but the address https://192.168.1.1/admin can't be displayed.
View 35 Replies View RelatedI have a Cisco ASA configured for Any Connect clients. I also want to pass 443 traffic back to an internal web server, but not sure if I can do this since the Any Connect clients are already connecting over 443 to the ASA, right?
View 8 Replies View RelatedUsing any computer and AnyConnect, I can connect to our network via ASA5500. But when I use Cius or iPAD, I always get a No License error message.
View 3 Replies View RelatedI am transitioning from a Microsoft ISA server to a Cisco ASA 5510. So far so good, until it comes to getting AAA functioning properly. I have a Microsoft IAS server that is functioning properly, however when I try to test it through the ASA's ASDM it errors out. When I run a packet trace it shows it's being blocked by the dreaded implicit ACL. The funny thing is that I can ping and traceroute to the IAS server from the ASA. I found numerous config examples for AAA using IAS, but still not working.
Could it possibly be behaving this way because my ASA and my IAS server are on two different internal netowrks? (172.31.1.x-ASA, 10.1.1.x-IAS)
I need connecting ASDM to ASA 5525x management port its a brand new ASA i just updated ios and ASDM port configuration is following
Management por 0/0 ip 192.168.1.1
secure-level 100
http server enable
http 192.168.1.10 255.255.255.255 inside
port is up
When I am launching Internet explorer it just said cant connect Chrome shows connection with 192.168.1.1 is was interrupted but i can ping asa and backward .
I'm trying to access my ASA 5505 by https://192.168.1.1 but I can't. I'm using Windows 7. I already have installed ASDM and I can enter in the box by ASDM. I am preparing to reformat my PC and I'm afraid that I won't be able to access my ASA if I do.
The Mozilla show the message: An error occurred during a connection to 192.168.1.1.Cannot communicate securely with peer: no common encryption algorithm(s).(Error code: ssl_error_no_cypher_overlap)
I'm trying to connect to something through an ASA.My traffic is coming in on a DMZ interface (security level 0) and going to something on a DMZ3 interface (security level 50).
From the GUI I configured NAT exemption from the source network (on DMZ) to the destination network (on DMZ3) therefore following the guidelines that the translation is set up from most secure to the least secure interface
I have no network connectivity to the host I need to get to From the GUI I removed the NAT exemption rule and configured a static NAT translation instead, translating the source (on DMZ) to itself (on DMZ3) - still no joy.The ACLs in place are fine, if I use the packet tracer tool, it fails at the NAT stage; [code]
I can't see what's wrong here. I've configured static NAT or NAT exemption between inside and outside or inside and DMZ many times over the last 10 years but can't work this out.the only thing I can thing of is that there might be a bug that affects DMZ to DMZ NATing, as everything between inside to DMZ and DMZ to Outside works fine.
i am working on a project with 2 security ASA's 5520 with Microsoft ISA/TMG-2010 Server having 2 DSL's my question is regarding the designing issue where should i connect the 2 DSL's using ISA/TMG-2010..
View 1 Replies View Related