I have a Synology DS 710.And I would like to set it up so i can access it from any where within my network. But also be able to access remotely either by my Iphone and my MAcbook pro.
I tried setting up a VPN but I find that I would get the basic setup done on my 710 and my mac. but my mac can not connect. Also find that I would need a password but not sure where I would create/find a password.
Kinda narrowed it down to the ds1512+ to replace a whs2011 (that was made from a hp media server). No rush. Just upgrading. What is the refresh cycle? I can wait until the new servers come out.
I'm not smart or dedicated enough to build a box from scratch. I just want it to work neatly.
I am extremely new to network but also excited with the things you can achieve with a Cisco switch.For about 3 months I sat down looking at my "Cisco C2950-24 Switch", this surely for such a beastly looking thing it must be able to do something other than just allow you to plug in cables. So with that said I started to do some reading and watched a couple of You Tube Videos.I am on the route to complete my first goal and thats have my own VLAN setup with 1 Server and 6 clients. The Server is running ESXi therefore a few other servers are running inside it too.So my VLAN - VLANID 20 running the network 172.22.22.0. On the physical switch I have the following:Port 1 - WAN incoming connection from my Router on the network 192.168.178.0Port 2 thru 9 all running on VLAN 20.By the way I am using the GUI Cisco Network assistant
View 4 Replies View RelatedI bought a Synology DS411 slim NAS which I want to access remotely. I made a DNS and did portforward in my router (Cisco by Linksys WRT160N v2. The problem is I am part of a bigger scientists network where all ports are closed so it wont work. I even tried installing a OpenVPN server on the NAS and then connect though that but with no luck.
View 3 Replies View RelatedHaving a hard time hosting my email service on my DS212J. To be I honest, I have no idea where to start.
Info:
IP Address using Synology DDNS: example.synology.me
Domain: example.ca
I have a client who has asked me to "optimize" their network.They currently have a few shared folders that everyone can see, but what they want is to restrict access to some of the computers on the network.More specific,they don't want the receptionist and the backroom workers to have access to those shared folders while the rest of the employees (the bosses) do have access to those folders.They have 2 computers with Windows 7, 2 computers with Windows XP, and a mac.
View 4 Replies View RelatedI am trying to set up a Synology VPN server thru a cisco RV220W and cannot get a windows 7 VPN client to connect to it. Access rule was created on RV220W to port forward 1723 and also made sure the same port was forwarded on the built in router on the Synology NAS box, running DSM4.1 and made sure VPN server was up and running. IP address of synology NAS is 192.168.1.250, mask of 255.255.255.0. DNSgateway is 192.168.1.1. Only running PPTP at this time.
When I run the windows 7 VPN client, I try to connect to the external internet addres:1723, make surePPTP is the only protocol and use a DNS of 192.168.1.1. When I try connect, I get an 868 error which says "error 868: The remote connection was not made because the name of the remote access server could not resolve."
When I try to ping port 1723, I do not get a response which leads me to believe that the issue is the router and not the NAS box. HTTP, HTTPS and FTP ports work fine.
My Windows Server 2008 r8 has 2 network card
1st card I have connected to Internet Router
2nd card I have set up the LAN to access the database application from server with 2 clients.
Question
1) Currently 2 clients can't access the internet
2) How to setup the 2 clients to be able to access to internet?
I have a 4 year old Linksys WRT54G V8 I'd like to set up as an access point for an Xbox 360 or DirecTV box. I am using a Linksys E3000 as my wrieless router, atm, and was wondering if there was anyway to use the WRT54G as an access point before I go out and buy other network adapters to get these devices connected.
View 2 Replies View RelatedI have a Dell switch setup with 2 Vlan's. Vlan 1 is to the network. Vlan 20 is going to be for wireless access to the internet. How do I configure the switch/router so that Vlan 20 only connects to the internet and not the network? I will later want to have a 2nd SSID that I want to connect to both the internet and network.
View 5 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 2.1 v000c.0 Build 130415 Rel.34164n
ISP : plusnet
I have setup 2 vpn tunnels from my TD-W8970 to places that use TD-8960N (Firmware Version: 1.4.0 Build 110921 Rel.17774n Hardware Version: TD-W8960N v3 0x00000002 )and I can ping and connect to any ip used at their end but they can only ping 192.168.1.1 which is my router and not 192.168.1.104 which is my Synology DS212J that they need to access.
Both tunnels are similarly configured:
Tunnel 1 on my TD-W8970
IPSec Connection Name: Tony1
Remote IPSec Gateway Address(URL): 89.240.xx.xx
Tunnel access from local IP addresses: Subnet
IP Address for VPN: 192.168.1.0
IP Subnetmask:255.255.255.0
[URL]
I have a Server 2008 server and a Synology DS1511+ Nas.The goal is to make an iSCSI connection from the Synology to the Server 2008 server. However, I am having an issue. I set this all up two weeks ago. For two weeks it was all running fine. Now, my iSCSI drive is dropping daily. And everytime I go into the iSCSI initiator and click anything, the server still allows me to do some things, but it basically locks up. I can't restart, services stop responding, etc... The only was I can break it out of that is a hard reset. Why iSCSI initiator keeps taking down my entire server to the point of hard restart? Once this is solved, I bet the iSCSI dropping daily will be solved as well. I have already talked with Synology, the log is producing nothing and they are suspicious that it has been running fine the past two weeks. Windows update is off (I manually do it during scheduled maintenance), and there is no av or firewall running, so rule those out.
View 8 Replies View RelatedI've just bought a Synology DiskStation DS412+ and put 2 x 3TB Western Digital Red drives in it, set up in RAID 0. It's currently plugged in to my gigabit Netgear switch.I created a user with full permissions on the NAS, created a share, mapped a drive on my Windows 7 PC (also gigabit ethernet) and tried copying some files, but I'm getting painfully slow transfer speeds (< 40KB/s - yes, kilobytes, it's not a typo!
Does anyone have any ideas why it'd be so slow? There's loads of reports online of people getting > 80MB/s from this NAS.
I've copied files from this PC to my MacBook Pro in the past and got decent enough speeds so it shouldn't be an issue with the NIC on this PC, or (hopefully) the Netgear switch it's going through.
I am looking up setting a VPN using ASA 5505s so we can connect a mobile network of computers to our base network of computers. The base network has a static public IP address, but the mobile site will not. I was thinking of using a remote access VPN setup, but I am unsure if I can have a network of computers connecting in to the remote access VPN setup.
View 5 Replies View RelatedI have a Cisco 881 setup with the following VPN config.
[code]...
The client is able to connect just fine to the network via VPN, but I am unable to gain access to any of the local resources. I know 192.168.1.1 has SSH running and 192.168.1.50 has telnet running but if I try to connect to either using the correct program they just timeout. I am really at a loss on why the vpn connection connects but I can not gain access to any of the resources on the VPN network.
I just bought a synology NAS ds212j . I updated to DSM4.0. I purchased 2 Seagate ST2000DM001 Barracuda 7200RPM 2 TB SATA 6 GB/s NCQ 64 MB Cache 3.5-Inch Internal Bare Drive
My e3200 has the latest 1.0.04 firmware I'm backing up via time machine(mac book pro) in MAC 10.7.4 which has a wireless N card.
in Utilities (activity monitor)I'm only getting 9 megabytes per second , why is it so slow? I feel like it's taking forever. e3200 says it does up to 300 megabytes per second. any possible settings causing this?
a backup of 202 gigs has been running for about 4 hours and still going
Was told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?
View 3 Replies View RelatedI have a Linksys EA4500 setup on my corporate network for wireless access. I have enabled the guest network and from all I can tell it's on a seperate subnet from my internal network like it should be. 192.168.x.x My internal is on a 10.x.x.x network. I conenct to the guest network using a laptop and I'm prompted for a password to get to the internet, which I like. The one issue I'm seeing is when I'm connected to the guest network I can still do an RDP session to internal resources. How is this possible if the guest network is on a seperate subnet?I take a laptop which has not been joined to my domain, connect to the guest ssid, and then open an RPD session and enter an IP address for an internal server and it connects. Is there a setting to keep this from happening
View 6 Replies View RelatedI am trying to setup internet access and intranet access using two cards per PC. I don't have sever software and I want to be able to share files between several machines. I have two routers. One that connects to cable modem and one that connects to intranet side. I have assigned different static ip addresses to both cards.
View 6 Replies View RelatedI have have my Dir-655 set up as an access point for awhile and would like to change the wireless access code. I can't seem to figure out how to access the setup menu while it is an access point to do this. How I access the router when it is set up as an access point?
View 4 Replies View RelatedI want to setup a DC++ HUB for sharing data within the university local network. We have addresses of the form 172.31.*.*. These addressed are accessible within the university bu non routable outside on the internet. My plan is to setup a local HUB for DC++ for sharing data within the university intranet. So even if internet is unavailable data can be exchanged through LAN. This HUB must not be accessable outsied the university network.how should I do this all..implementing network sharing other than DC++. My basic idea is that everybody can share their data and the data is searchable from one common interface( Web interface is better option, if possible). And data featching should prefferably be from many hosts, using multiple connections so that speed can be improved..
View 4 Replies View Relatedi'm connected to the internet through a shared internet connection through a switch,and also have 3 computers connected to the same switch,what i want to setup a local network between the 3 computers but separated from the internet network?
View 6 Replies View RelatedI am having problems setting up a network, recently bought a used linksys router and had to restore to default settings. Now I am trying to set it up but I cant go to the ip 192.168... it times out, but when I go online and do the same thing I get a FW-1 at checky: Access denied. error. This is obviously my first time setting up a network using a router. what am I doing wrong? I checked drivers and I have tried plugging the cat5 into both internet and the 1st and 3rd port with little success, either a timed out connection or an error.
View 9 Replies View RelatedI had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View Relatedi am trying to setup access to the net on my ASA i have 2 different subnets on the inside and one to my outside hooked into TWC cable i am not sure i have the config right i am in the testing phase. I also have a vpn tunnel to a c2811?
View 7 Replies View RelatedI have a D-Link DIR-615 and am trying to set up the Access Control so that I can restrict Internet connection from midnight till morning (to keep my teenage kids from staying up half the night on the Internet)I can step through the Access Control set up, but I don't see how I can block only one MAC address or computer from accessing the internet at specific times.
View 14 Replies View RelatedI am trying to configure a Linksys RV042 VPN router as a simple router. I want to connect it to one of the ports from a CiscoASA5505 router because I need to connect 4 additional PC's and the ASA is out of available ports.I am trying to connect it through an ethernet port from my laptop.At first I configured the TCP/IP settings as getting the IP and DNS's automatically and but I was able to enter the setup by entering the default IP address (192.168.1.1).After 10 minutes it got disconnected and could not connect again.I get Status: Limited or no connectivity.If I try to type the IP address manually (192.168.1.1) I can ping the router successfully but the setup webpage never opens.what I need to do in order to access the setup webpage when I connect the router directly to my laptop?
View 10 Replies View RelatedI am trying to set up a minecraft server but I am having trouble port forwarding. I port forwarded a linksysWRT160v3 router but still nobody could connect. So I read online that I might have to also port forward something sitting next to my router. (IDK what it is, i think its a modem or something) It is a Efficient Simon Speed Stream 5100. It says to type in 192.168.0.1 in my web browser for advanced setup but when I did it took me to a search engine.
View 3 Replies View Relatedi need to do the following:
-go to routers startup page
-log in
-look for my WAN MAC address
it seems so easy, but i keep getting instruction to do things like type in different numbers into my browser which never work.
when i was on my linksys setup page 192.168.1.1 i accedently disabled wireless web access now i cant undo it so now i cant use wifi
View 1 Replies View Relatedi can't access the internet without the internet setup disk.I don't have it anymore does anyone have a spare
View 19 Replies View RelatedI need to setup my LAN card to access 2 gateways.
OS: winXP sp3
IP: 192.168.1.101
One gateway is 192.168.1.254 to the internet.Another gateway is 192.168.1.253 to access (via VPN) the other subnets 192.168.x.x? I can even install a second lan card.
Setting up a home network for someone who does not know any of the settings for the router, "someone" set it up for her. A laptop running Vista was accessing the network, a cable modem is used.I added a Windows-7 desktop, no problem. Connected an HP printer to desktop, no problem. Tried to connect HP printer which has a wireless function to wireless network, no-go, cannot find the security key to configure the printer.Tried to access the router with 192.168.0.1, admin screen shows, user does not know anything about password, tried default username, Admin with blank password, no-go.Reset router,
View 5 Replies View Related