Kinda narrowed it down to the ds1512+ to replace a whs2011 (that was made from a hp media server). No rush. Just upgrading. What is the refresh cycle? I can wait until the new servers come out.
I'm not smart or dedicated enough to build a box from scratch. I just want it to work neatly.
I bought a Synology DS411 slim NAS which I want to access remotely. I made a DNS and did portforward in my router (Cisco by Linksys WRT160N v2. The problem is I am part of a bigger scientists network where all ports are closed so it wont work. I even tried installing a OpenVPN server on the NAS and then connect though that but with no luck.
View 3 Replies View RelatedHaving a hard time hosting my email service on my DS212J. To be I honest, I have no idea where to start.
Info:
IP Address using Synology DDNS: example.synology.me
Domain: example.ca
I have a Synology DS 710.And I would like to set it up so i can access it from any where within my network. But also be able to access remotely either by my Iphone and my MAcbook pro.
I tried setting up a VPN but I find that I would get the basic setup done on my 710 and my mac. but my mac can not connect. Also find that I would need a password but not sure where I would create/find a password.
I am trying to set up a Synology VPN server thru a cisco RV220W and cannot get a windows 7 VPN client to connect to it. Access rule was created on RV220W to port forward 1723 and also made sure the same port was forwarded on the built in router on the Synology NAS box, running DSM4.1 and made sure VPN server was up and running. IP address of synology NAS is 192.168.1.250, mask of 255.255.255.0. DNSgateway is 192.168.1.1. Only running PPTP at this time.
When I run the windows 7 VPN client, I try to connect to the external internet addres:1723, make surePPTP is the only protocol and use a DNS of 192.168.1.1. When I try connect, I get an 868 error which says "error 868: The remote connection was not made because the name of the remote access server could not resolve."
When I try to ping port 1723, I do not get a response which leads me to believe that the issue is the router and not the NAS box. HTTP, HTTPS and FTP ports work fine.
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 2.1 v000c.0 Build 130415 Rel.34164n
ISP : plusnet
I have setup 2 vpn tunnels from my TD-W8970 to places that use TD-8960N (Firmware Version: 1.4.0 Build 110921 Rel.17774n Hardware Version: TD-W8960N v3 0x00000002 )and I can ping and connect to any ip used at their end but they can only ping 192.168.1.1 which is my router and not 192.168.1.104 which is my Synology DS212J that they need to access.
Both tunnels are similarly configured:
Tunnel 1 on my TD-W8970
IPSec Connection Name: Tony1
Remote IPSec Gateway Address(URL): 89.240.xx.xx
Tunnel access from local IP addresses: Subnet
IP Address for VPN: 192.168.1.0
IP Subnetmask:255.255.255.0
[URL]
I have a Server 2008 server and a Synology DS1511+ Nas.The goal is to make an iSCSI connection from the Synology to the Server 2008 server. However, I am having an issue. I set this all up two weeks ago. For two weeks it was all running fine. Now, my iSCSI drive is dropping daily. And everytime I go into the iSCSI initiator and click anything, the server still allows me to do some things, but it basically locks up. I can't restart, services stop responding, etc... The only was I can break it out of that is a hard reset. Why iSCSI initiator keeps taking down my entire server to the point of hard restart? Once this is solved, I bet the iSCSI dropping daily will be solved as well. I have already talked with Synology, the log is producing nothing and they are suspicious that it has been running fine the past two weeks. Windows update is off (I manually do it during scheduled maintenance), and there is no av or firewall running, so rule those out.
View 8 Replies View RelatedI've just bought a Synology DiskStation DS412+ and put 2 x 3TB Western Digital Red drives in it, set up in RAID 0. It's currently plugged in to my gigabit Netgear switch.I created a user with full permissions on the NAS, created a share, mapped a drive on my Windows 7 PC (also gigabit ethernet) and tried copying some files, but I'm getting painfully slow transfer speeds (< 40KB/s - yes, kilobytes, it's not a typo!
Does anyone have any ideas why it'd be so slow? There's loads of reports online of people getting > 80MB/s from this NAS.
I've copied files from this PC to my MacBook Pro in the past and got decent enough speeds so it shouldn't be an issue with the NIC on this PC, or (hopefully) the Netgear switch it's going through.
I just bought a synology NAS ds212j . I updated to DSM4.0. I purchased 2 Seagate ST2000DM001 Barracuda 7200RPM 2 TB SATA 6 GB/s NCQ 64 MB Cache 3.5-Inch Internal Bare Drive
My e3200 has the latest 1.0.04 firmware I'm backing up via time machine(mac book pro) in MAC 10.7.4 which has a wireless N card.
in Utilities (activity monitor)I'm only getting 9 megabytes per second , why is it so slow? I feel like it's taking forever. e3200 says it does up to 300 megabytes per second. any possible settings causing this?
a backup of 202 gigs has been running for about 4 hours and still going
A day ago, I was having trouble with my apartment modem, and due to a busy schedule, was only able to do a quick "Unplug and reset" which seemed to work at first, but eventually it stopped working all together. Today, I traveled from my apartment to my "home" home, where the wireless network is set at a "Home" security level. However, my wireless now will not connect at all. It continues to cycle through "Identifying" yet cannot make the connection. It works through a LAN connection however.So far, I've attempted the follow:
- run>ipconfig/all, ipconfig/reset, etc
- winsock reset
- system restore
My computer is a Samsung RC512, running windows 7. Here's the paste from my ipconfig/all:
Windows IP Configuration
Host Name . . . . . . . . . . . . : PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : hsd1.pa.comcast.net.
Wireless LAN adapter Wireless Network Connection 2:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter
Physical Address. . . . . . . . . : DC-A9-71-93-16-52[code]....
recently bought a new Linksys EA3500 that is connected to my SB5120 cable modem. For two weeks it's been running smoothly but when my cable modem is in need of a power cycle.I power cycle both the router and modem but my connection is lost. it's after countless hours of messing with the two I'll get the connection back but I'm afraid it'll lose connection again, that and I fear I may have enabled bad options.
View 10 Replies View RelatedI have access controls setup on my DIR-825 which work fine until there is a power outage and my router comes back up.I am using Automatic Time Configuration and have the NTP server set to ntp1 [URL]When the router comes back up I checked to make sure the NTP server option is still enabled, and it is, however the current time is totally wrong.To fix this I had to go to the pull-down, select 'ntp1.dlink.com' and then save the settings. After this the time is correct again.This is as bad as not having the Automatic Time Configuration option at all, since I can't guarantee that the power won't go out. I do not have a UPS hooked up to back up the router, nor do I see why I should need one if the Automatic Time Configuration actually worked.know if there is a way of making the Automatic Time Configuration reliable so the time on my router is automatically corrected when the power comes back up?
View 3 Replies View RelatedIt seems there's no way to reboot this device from the browser interface. You have to actually go and recycle the power by physically pressing the button.Plus, to setup Port Forwarding you have to reboot the modem.This is a major problem because it means you have to be on the premises to change things like the port forwarding. You setup it up, but have to reboot for it to take effect.
View 1 Replies View RelatedI have the following equipment
1 x AIR-WLC-2106-K9 (IOS = 6.0.199.4)
4 x AIR-LAP1131G-E-K9 (IOS = 12.4(21a)JHB1)
All configued ok with 2 SSID's associated to 2 VLANS all operates as expected.However every few 2 to 12 hours the WLC crashes, locks up.Unabale to contact via telnet or browser, will not respond to ping.The LAPs remain up but the WLANS go off air etcOnly a physical restart of the WLC will bring it back.
I'm having a little issue with some Cisco Aironet1242ag WAP's. I receive a call at least twice a month stating that some of the WAP's are not giving out internet connection. What I always do is go to my patch panel and disconnect those WAP's not working and connect them back again so they can power cycle. These WAP's are connected to a Cisco3750g. Once the WAP's boot up, the users can connect to the WAP and connect to the internet.
I don't know if these WAP's are filling up with some information that causes the access points to not connect to the WAN.
I've setted the unit in BRIDGE MODE, and attached on it 3 LAN devices, 1 PC Desktop, 1 NAS WDBE and 1 HP printer ... OK all config process was right and all my units talk togheter via AP Netgear DNG2000, and so i can use for instance the printer with my laptop too connected in WI-FI N. Now usually, In the night I turn off all my devices (DAP included), and when in the morning I need only the printer used by my laptop, obviously I turn on ROUTER - BRIDGE - PRINTER - LAPTOP but NOT the DESKTOP ... and so the DAP can't reconnect automatically to the router (both the lights AP/BRIDGE are on and fixed) ... I turn on the PC and the BRIDGE reconnect to the world .... BUT I DON'T WANT turn on everytime the desktop !
1) all gears has fixed IPs
2) DHCP server deactivated on the AP main router (DNG2000)
3) no WPS used, only WPA2-PSK (AES) personal keys on all gears
once that DAP-1522 is connected to the router .... all work fine (also when I turn off the DESKTOP).so the workaround is never turn-off the DAP ? I can't believe ... and who will save the energy planet
I have a Cisco 1841 Router with ADVANCE IPSERVICE IOS .The said router does not safe config, even after saving the config? As soon as the power cycled all the config will be lost? what can be done to correct this ?
View 1 Replies View RelatedCisco 2800, 12.4(23b) router has two VPN tunnels to other Cisco devices.
Authentication uses certificates from a PKI CA server. Under normal circumstances all works fine, both crypto sessions up.
After a power cycle (having first saved configs) however, the crypto sessions are stuck in DOWN-NEGOTIATING.
The certificate on the router still looks valid.
The only way to get the sessions back up is to renew the certificate, which seems strange as the existing one appeared to be still valid.
We have some 1242 LAPs in a two 5508 controller setup working fine. All LAP are configured to obtain address from DHCP. After first join we usually change some configs like HOSTNAME, AP GROUP, PRIMARY AND SECONDARY WLC. After a software restart or a complete power off/power on the LAPs joins the primary controller and all configuration still there. We now add a 1142 LAP and is does not retain the configuration after a power off/power on cycle, but after a software restart there is no problem. The only way to retain the config is setting the AP with a static IP address.
We use WLC 7.0.116 and we see no errors in the LAP console.
I've just bought a pair of WAP121 for testing and validation. I've set it up properly (user/password, IP, management vlan, NTP, SNMP, 802.1x, etc). So far, so good, everything worked as expected. I've downloaded the configuration to my PC, and also saved it to startup-config. I've powered off the unit, went for a coffee, and powered it back. All my settings were lost.
Tried to restore settings from the file downloaded to my PC, but no luck. After reboot, it was factory clean, no trace from settings in the backup file. I've set it up again by hand, power cycled it, and the **** thing reloaded to default settings.
Faulty unit, I thought, so I opened the other one I have, and repeated the whole thing, but same results. Test were made using the power adapter supplied but also tried with a catalyst 2960 with PoE.
When our DSL modem drops its connection, even momentarily, the RV220W requires a power cycle before the computers on the LAN can browse again. When I connect to the router, the WAN Information displays the word Connecting, rather than Connected.
We have a DSL modem connected to the router, the router connected to an ethernet switch, and our small business pc's connected to the switch.
Firmware on the router is 1.0.4.17
I have a brand new 2960S-48TS-L, plain vanilla with no extra module/boards etc. It boots up ok (the installed version is 12.2 (55) SE5) but then constantly cycles the following error, and doesn't accept any input whatsoever. After 5-10 minutes of cycling the error, the switch reloads and starts the process again.
PCIE0: link is NOT up.
--------------CPU's PCIe SDR Registers--------------------
PE_DLPSET = 00401000
PE_UTLSET1 = 00000000
[Code]......
I have an E1200 and if a device - such as my tablet or laptop - is left unused for a period of time - say for 4 or 5 hours - they won't reconnect to the router unless I do a power cycle/reset on the router.
View 5 Replies View RelatedWe have a Model WRT54GLWireless-G router. At least once a day it loses it's internet connection. All computers that are wired to the switch that is connected to it lose their internet as well as any wireless devices. I have to manually power-cycle the router to get internet back.
View 9 Replies View RelatedI have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success.
View 7 Replies View RelatedIs it possible to upgrade the CSACS-1121-UP-K9 to be a non upgrade part? We were going to upgrade from a Windows 4.x to the above Appliance (version 5.x) but there is now a reason to keep the old Windows version running therefore we cannot give the new Appliance the old ACS's licenses?!So we should have (with hindsight) bought a fresh version of the ACS 5.x rather than an upgrade.
View 1 Replies View RelatedI am facing a problem to install a ap upgrade lic file on controller 5500. Iam getting the following error:
% Error: License file transfer failed - Error from server: File not found
I have confusion here that when I configure this command from GUI
tftp://172.32.45.22/cmm/standard.lic
What i should use for /cmm/ ????
Let say i have lic. file is on desktop of tftp server computer and I say in this command
tftp://10.12.70.35/??/license file .lic
dell xps m1530 i have a Intel� PRO/Wireless 3945ABG Network Connection and i want to upgrade it to N standard which model of intel minipci network will fit to my dell?
View 4 Replies View Relatedinstalled in 2006 .Having connection issues
View 2 Replies View RelatedI've been trying for years to update my firmware but I'm still on version 1.21. I've never been able to update. I found the information in the discussion below but I get the same error message every time. The uploaded firmware file may not be correct. You may have uploaded a file that is not intended for this device, or the uploaded file may be corrupted.If the uploaded file is correct, it is possible that the device may be too busy to properly receive it right now. In this case, please try the upload again. It is also possible that you are logged in as a 'user' instead of an 'admin' - only administrators can upload new firmware.I tried every version of the firmware and I get the same error every time. I'm logged in as admin, I'm connected to the computer through port 1, I've done the factory reset, I've rebooted... about 100 times now.
View 5 Replies View RelatedI have some requirement where I need to upgrade the ACS 4.2 to 4.3, are there many upgrades available from Cisco on this ?
View 5 Replies View RelatedHow to upgrade IOS XR from 4.1.2 to 4.2.0? Is their any specific requirement for same? What precaution i have to take while upgrading process?
View 1 Replies View RelatedI have a project to upgrade LMS3.2 to a new PI 1.2. my current plan is
1. build a new VM to install LMS 4.2
2. backup LMS 3.2 ( not SP1)
3. import 3.2 data to the new 4.2 machine
4.build a PI 1.2 and import 4.2 data into PI 1.2
5. run the devices side by side untill parity
As 3.2 is not SP1 can the data still be migrated into 4.2 or will I need to upgrade 3.2 to 3.2.1 ( SP1)? Is there a script to backup/restore data from 3.2 to 4.2?