My house has wifi before phone guy came and set up wi fi cordless phones worked now it sounds like i am talking in a tunnel and the other party can not hear me.. my corded phone works fine phone company told me to get new cordless phones.. currently have 6.0 have tried 5.8.
View 1 Replies
I'm having an issue with my work laptop. I'm just setting up a wireless connection for the first time. I bought the Linksys E1000. I have used this laptop at work and at hotels for a 54 MbPS connection. I set up the Linksys at home. It sees the network and will tell me that it is connection at 54 MbPS. Then it quickly goes down to 11 then 5.5 then 2. Eventually it runs so slow that I time out of the security portal at work because its so slow. Occasionally it even loses the network and has to find it again. I'm only about 20 feet away from where the router is located. I have hung up all cordless phones and turned off my cell phone.
View 2 Replies View RelatedI purchased Linksys WAG160N (from a store) and I also have 7 Linksys SPA962 VOIP phones provided by MyNetPhone with service included. All tests we found out that this modem doesn't work with this VOIP phones. Somehow probably doesn't give access to MyNetPhone servers to get connection with this phones.I purchased an other one from DLINK and works perfect?
View 1 Replies View Relatedprovide a sample Voice Vlan configuration for the Cisco 2960 POE switch to work with the Non-Cisco IP Phones?
Will these commands work? Vlan 2 is the new voice vlan, Vlan 1 is the data vlan.
mls qos
interface fastethernet 0/1mls qos trust cos switchport nonegotiateswitchport mode trunkswitchport trunk encapsulation dot1qswitchport voice vlan 2priority−queue outspanning-tree portfastspanning−tree bpduguard enable
vlan 2name voice
I have a CUCM BE environment with a number of remote users with 8961 phones connecting to an ASA 5501 via AnyConnect. The phones register fine and can make inbound/outbound calls as well as four digit dialing to other users at the corporate site.
The problem is when a remote user tries to four digit dial another remote phone. The called phone will ring but there is dead air once answered and then the line goes dead.
This sounds like a routing issue to me. How to get AnyConnect clients to be able to reach each other?
We have 2 land lines in our house and I have an Adsl system installed on one of them (lets say line2)The problem is when I connect the panasonic cordless phone to line1, after 15 to 30 mins the adsl malfunctions on line2!I have checked the line1 with another panasonic cordless phone (older model) and the problem doesn't persist.I have used adsl filter and it didn't work and I can't throw out our new phone and use the old one!
View 5 Replies View RelatedI have a cordless phone which broadcasts on 2.4ghz - when the phone is being used it cuts out the wifi. I thought that with the E2500 being a dual band - I wouldn't have this issue as I thought the router would switch to the 5 Ghz frequency if there was interference on the lower band. Maybe I am not understanding how the dual band works.
View 3 Replies View Relatedwhy our PBX system would freeze up the phones. There is no real reason why this happens. We have the PBX on its own circuit board, so its not sharing any power, we only have about 200 phones on the system, so that is not the issues. Its properly cooled. It just seems to happen that our phones freeze, and when they start freezing it seems to happen in pairs.
View 1 Replies View RelatedI' trying to access my Gmail account from my IP Phone (Cisco IP Communicator, don't have an actual device at the moment). The services work greatly (I tested berbee services and they work fine) I came across the Gmailcheck service. [URL] I downloaded all the files and added the "statusMsg.php" in my services list. Now when selecting Gmailcheck on the IP Communicator, it just shows the PHP code script : No interface, no gmail...
So I'd like to know : How to do to make this PHP script work ? Or is there a better way to access my Gmail accounts ?
how to connect wifi on mobile phone? how it works? my handset is LG T310i having wifi facility
View 1 Replies View RelatedPhones will not link to my wireless modem?
View 1 Replies View RelatedI have a new install with 3 SF300 switches, setup as vlan 2, the switch connected directly to the 2901 router has no problems, plug in a phone and it gets an IP, but if connected to either of the two swtiches behind the first switch, they do not get an IP. I am seeing the DHCP request hitting the router, and the router sending the IP to the phone, but it never gets the IP.
*Jun 15 10:40:20.040: DHCPD: client's VPN is .
*Jun 15 10:40:20.040: DHCPD: Sending notification of DISCOVER:
*Jun 15 10:40:20.040: DHCPD: htype 1 chaddr 40f4.ecef.bded
[Code]....
All ports are setup as trunk on vlan 2 including the ports that connect the switches together. Not sure what the problem is, but they are going live tomorrow and only have 48 out of 120 phones.
I have signed up with Axvoice for cheap voip calls. My problem is I am trying to use three phone sets with the same adapter (grandsteam HT 286). In accordance with Axvoice's live support instructions, I have plugged the main phone jack of my house into that adapter. I am getting crystal clear voice quality in one phone set. That obviously indicates, there is no problem with the service. However, on two phone sets, voice is not clear and I am having noise and sudden call breaks. I have checked all the ports but could not find anything. I am jobless right now.
View 2 Replies View RelatedIf you have some clusters with +8000 phones, how would you plan a strategy to upgrade the firmware of all the phones?
If the 8000 phones are reset the network BW could be come a real mess. Besides the CM could hang with so many tftp downloads.
The approach is going resetting phones in little sets, like ten phones a time.
I have pretty much the EXACT same issue. Revo 3700, Sky Unlimited Broadband, and a bunch of laptops and phones that can connect to the internet anywhere in the house without a probleI had the Revo connect all day last Friday (for the first time), prior to that it had connected a hand full of times, but only a very slow connection. For the last 4 days it hasn't connected at all, but says the signal strenth is 4 or 5 bars. I'm typing this from right next to the Revo on my laptop without any issue.
View 4 Replies View RelatedI have a problem with my Cisco 7961 phones not registering on my CUCM 8.6 install on ESXi 5. Weird because I have Cisco IP communicator phones that register with no problem. You guys know what I can be missing. I have restarted the CUCM and services multiple times. The phone log on my phones say it can't find dhcp and DNS unknown host but my CUCM is configured by IP address. I also attached some screenshots
View 3 Replies View RelatedI have an issue that my 4 daughters are accessing the internet at all ungodly hours of the night via their mobile phones and ipods. Not only should they be in bed but they are racking up our internet useage. We can't turn off the router altogether as one of those daughters, is also up at ungodly hours, with Uni work and another doing her finals for Year 12. Am i able to block their access somehow through the router without loosing the entire internet?
View 4 Replies View RelatedI have an HTC INSPIRE cellphone and I would like to get free Wi-first wherever I go.
View 3 Replies View RelatedWe have customer with implementation ACS5.2 in Windows environment. Now they want to implement IP phones in the network.
View 0 Replies View RelatedI am working in Private IT company. The facility is having 4000 users and it is a high resliency site having two core switches and nearly 40 access switches. All core and access switches are 4506E switches and odd vlan is taking core-1 and even vlan is core-2. We are having cisco ip phones 6921 connected as daisy chain.( Phone is connected to access switch and the desktop is connected to ip phones). The Ip phone are getting registered cisco call maneger server. The call manager one leg is connected to one core switch and another one is core 2 same like my DHCP server.
For all vlans the the default gateway is my firwall. The voice needs to hit the call manager, hence we have implemented a source routing to call manager for the voice vlans. the problem is once we down the Core-1 some of the IP phones are not getting registered no matterit is on odd or even vlan. The same issue for Core-2. We suspect that there might be some issue in the DHCP server for voice vlan routing. But server team is saying that there is no issue with the DHCP server.Now network is vulnerable that if any core switch is down my voice ip phones will be down.
I have some Catalyst 3560 PoE switches running the latest 12.2(50)SE1 image. I have a working configuration for STP, QoS, Voice & Access VLANs, Port-Security & IGMP snooping - I stress this is working PERFECTLY. Now I have been playing with wired 802.1x port authentication for a while which again I have sucessfully deployed on ports without IP Phones. I did some more testing with 802.1x clients behind some Cisco IP Phones and after understanding the issues and workarounds I thought I had a working environment. The environment is XP SP3 with the new separate wired 802.1x supplicant, workstations are all in a 2003 AD Domain and the wired 802.1x settings are configured through group policy. I had issues with Windows Server 2003 SP2 not working behind IP Phones but this I put down to the supplicant being different from the new one in XP SP3. MS don't have any plans for Server 2003 SP3 (or XP x64 SP3?) nor can I find any hotfixes to resolve this so it's a 'caveat'.Anyway I have tested this many times and with XP SP3 and the new supplicant it all seems to work well (only the access VLAN is using 802.1x Authentication, I am not authenticating the IP Phones via 802.1x).
Now today it stopped working and 802.1x clients behind the 7970 IP Phones no longer authenticate. I have spent an hour or so looking at this and the IOS is the same, as is the configuration on the IAS (Radius) server, as are the XP clients. I was scratching my head a bit and then looked at the IP Phone - the software on the phone has been upgraded to 8.5(2) - previously it was 8.4(4). I managed tp downgrade the software via CUCM to 8.4(4) and it now works. I have retested it several times so this is obviously an issue (either a new feature or a bug?) with the latest code for the 7970. I have checked and it's the same codebase for all the latest IP Phones - 7906, 7911, 7931, 7941, 7942, 7945, 7961, 7962, 7965, 7970, 7971 & 7975 which was released on 1st June. I have looked through the release notes and EAP-FAST has been added but this is an update to the EAP supplicant on the phone and not a feature of the 802.1x pass-thru from the attached device. I can find no other 802.1x or EAP references.
PoE works fine with C 1131/1141 Access Points and C-7975 IP phone but PoE does not seem to work on 7960 Phones nor on the C-1121 Access points
All devices work properly with the Cisco power injectors or on a Cisco Cat-29XX switch
Is there a trick to make PoE work for older devices ?
I want to connect a 6911 IP Phone to a SG 300 switch. This is my scenario: vlan 3 data, vlan 9 voice, vlan 10 admin.I have a trunk on port 10 of the SG 300 (vlan 1 untagged, vlan 3,9,10 tagged) and it is connected to a switch 3560, this switch has all the L3 configuration of the vlans and the SG 300 switch has an IP on the admin vlan (10).Also i added the OUI of my IP phones an created an LLDP Policy. Right now I have a 7941 IP Phone working but 6911 is not working. Iam using the new version 1.1.0.73 that supports CDP.
Also I noticed that even when my PC and IP phone receive IP address they can not ping each other nor the SG 300. They only can ping the default gateway or IP addresses in diferent vlans but connected on 3560 switch.
Looks like I still have an issue with LMS to recognize the IP Phones in UT as IP Phones. SNMP RO on Call Manager is enabled and is green in CM (e.g. topology) - so SNMP get is basically fine. The Phones are recognised as End Devices in UT.
As far as I understand, now if I start a Phone Aquisition, the CUCM is polled by LMS to gather additional information about the phones. So it seems there is a problem with the SNMP polling of the Call manager?
I am trying to configure my ACS to allow 802.11 phones to authenticate. I have searched high and low for documentation on doing this with no luck. We are using unified wireless with a mix of 5508 and wism controllers. I am able to authenticate windows devices against active directory via the acs but can't seem to get anything working with the phones.
View 3 Replies View RelatedI have a question regard to switch SFE2010P, i have 2 vlan ( data and voice) and we want to configure Ip phones SPA502G, the question here is how can i make to suport 2 vlans on the same switch port, like the catalyst IOS switch port acces vlan x and switch port voice vlan x, if i set up the switch with the voice vlan like tagged doesn't work, but if i set up the voice vlan like untagged vlan its works but the PC attached to the data port on the SPA502G doesn't work?
View 1 Replies View RelatedI have 2 (and maybe soon 5 more) 7940G phones to add to my network, which already has a Netgear POE capable switch. I've since discovered that early Cisco POE isn't the same thing as current POE, and the switch doesn't power the phones.
I was looking at adding a Cisco SD208P 8-port switch to power the phones, but I soon discovered it only has 4 POE ports, and I'm not sure that this switch will even power the 7940G phones. And if the other 5 phones show up, I'll need two of those switches with no room for expansion on the voice network.
Will this switch power those phones?Is there another small switch available so I don't have to replace my existing switch infrastructure to get these phones to work? Or do I need to scrap the phones and get something newer that will work with the current POE standards?
We have a Cisco ASA 5520 and use the Cisco VPN Client a lot, but I can't seem to to get Android phones to connect (Ice Cream Sandwich OS), it seems to want use Anyconnect
View 2 Replies View RelatedI have installed LMS 4.1 and discover all the devices (router/switches) but i want to show IP Phone on the LMS. I am unable to discover call manager in LMS 4.1 topology.
In Call Manager 8.6 in Cisco Serviceability under snmp setting i have enable the read community string and check snmp, MIB service are running.AM i using the correct proecdure. How can i get the Call Manager on LMS server so that i can see IP phones on LMS topology. 8.6 is installed on VM Ware.
I have some 79xx series VOIP phones that are acting VERY strange ... if you are familiar with these series phones once plug them into the PoE switch they look for a TFTP server with the call manager files to acquire all the info they need to work .... i have them set up on a 2620xm router running IOS c2600-ipvoicek9-mz.124-15.T14 along with call manger 4.3. My router is my TFTP server and i have hooked up and fixed over 50 of the same series phones with out a problem.
Now here is my issue ... when you goto press the SETTINGS button on the phone you are allowed to go into the settings of the phone to change all the ROUTER,TFTP,ETC info to allow you to connect your phone to the CALL MANAGER or you can set up DHCP and it will acquire the info automatically. When i press the SETTINGS button nothing happens .... i can reset the phone to factory defaults by holding the # button then 12345678*0# then 2 not saving the info and i can hit the restart buttons which is * 6 SETTINGS buttons together and that will let me restart the phone but i cannot manually set up this phone to do anything .. it will not acquire info form my DHCP server and will not find my TFTP server at all =( the phone SETTINGS BUTTON does not respond at all ..only when restarting the phone.
has anyone here played around with uploading compatible audio files for custom rings and MOH and/or personalized backgrounds for the phones? I was only taught the basics in our CUCM v6.0.1 and am looking to figure out how to get some good music on my phone as well as play around with other "cosmetic" features. The phone I'm testing with is a 7971(color).
View 4 Replies View RelatedA couple of users on my network complain about timeouts. They access the same server which runs a SQL server. People from outside world can access it without a problem but internally it keeps timing out. I have also noticed that VoIP phones have a delay internally. So if i pickup my phone and dial an extension the other person can't hear me sometimes but i can hear him.
I have experienced the VoIP problem but have never had any time outs on my machine. I tried packet capture on a couple of computers but i cant see anything out of the ordinary. Alot of ARP, some STP which i think shouldn't reach the machines, dropbox traffic etc.
I have an SRP547W hooked up as the office router with the standard office phones connected via the telephone ports at the back of the unit using 2 SIP lines as well as the PSTN by dialling hash first. We have just added a new staff member and bought an SPA303 with the intention of connecting it through registered SIP lines on the SRP547W, and hopefully have the facility to use the PSTN line when the SIP lines are busy.
The problem is, it connects to VLAN100 and gets its IP address and initializes fine however no lines show as configured and it can't make or receive calls. What do I need to configure on the SPA303 to tell it to use the SRP547W as its SIP Server/Proxy (not sure of the terminology).
