D-Link DIR-655 :: Enabling Wireless Causes It To Constantly Restart?
Aug 19, 2012
DIR-655 A4
Firmware: 1.35NA
ISP: Comcast
[Code].....
I play Diablo 3 and the lag that is created when the router restarts as well as getting booted, along with apps on my phones locking up are about to make me throw the DLink Equipment against the wall.
FYI - the Comcast modem was just upgraded to the Xfinity Voice modem becuase I puchased two Voice lines last week. The issue was happening before the new modem was insatlled, and after. According to the Comcast Modem's status page (192.168.100.1) the modem has been online for 4 days, 6 hours, and 31 minutes. So I know the modem has not been cycling.
View 3 Replies
ADVERTISEMENT
Mar 26, 2012
I'm constantly losing wifi connection and having to restart my Linksys E2500 router
View 4 Replies
View Related
Nov 16, 2012
For the past week or so I've been having trouble with my Wi-Fi connection. I have a desktop PC, a kindle and a PS3 that all connect to it.
If I turn on my Kindle after it's been off for a while it'll try to connect to the Wi-Fi but will keep alternating between 'Authenticating'/'Connecting' and never gets to the 'Obtaining IP Address' part so it shows the signal strength bars at the top but they're totally empty. If I go and unplug the modem and the router, let them sit for a minute, plug them back in the large light on the router will flash orange (it's usually green) so I press and hold the WPS button which begins to flash and then both lights turn green and the Kindle quickly connects itself to the Wi-Fi. If I don't let it go into sleep mode or turn it off it will stay connected but if it turns off I have to do the same modem/router reset. When I'm at school or work I have zero issues connecting their wireless networks.
With the PS3, if it's turned on while I reset the modem/router it will connect to the network but if it's turned off during the reset it will not connect when I turn it on later. Also, either way, it no longer connects to my media server (sharing files between the PC and the PS3) regardless of connecting or not.
View 1 Replies
View Related
Mar 1, 2012
A few weeks ago I noticed that at 9:00am sharp every morning my internet access dropped, and would come back up four minutes later.
The router is connected to a DSL-526B in bridge mode. My first thought was that the modem was playing up, so I factory reset it and reconfigured it.
I checked my ACLS and didn't see any rules that started or ended at 9:00 am so I just lived with it for a week or so until it got so annoying I contacted my ISP to see if they were resetting anything at 9am.
By accident, I saw that my wireless radio was being enabled aat 9:00am, as it had been for the last 2 years, when I first bought the router. But this problem has only started a few weeks ago.
So I changed the wireless schedule to see if that was really the cause for the reset, and sure enough, whatever time I changed the wireless schedule to, the router rebooted at that time.
I've also factory reset the router; twice; the first time I saved/restored my configuration, the second time I recreated all configuration from scratch.
why enabling the wireless radio resets the router, and why disabling it doesn't, and how to correct this behaviour?
View 14 Replies
View Related
Dec 13, 2011
just bought the DIr655 two weeks, everthing was fine except the wireless.almost every day around 6pm the wireless signal are disappear but the internet connection was fine with Lan, and i have to reboot the rounter inorder to get the signal back. i tried update the firmware but it it newest firmware on my rounter.
View 11 Replies
View Related
Jan 28, 2011
DLink 655 Fully Upgraded Firmware Multiple Laptops have the same issue, each has a different O/S from OSX to xp, vista and win 7. As soon as any laptop tries to download files, youtube, even web pages... There is nothing wrong with my wired connection. The thing is, each laptop gets disconnected then almost instantly reconnected. It is very annoying.The only thing I have found to fix it is turning off my wireless security completely. This is unacceptable! I am a computer scientist and in the security field. Ive tried WEP with both key sizes, WPA-Personal is what I originally was using before I started changed settings.
View 9 Replies
View Related
May 10, 2013
DIR 655
HW: A4
FW: 1.35NA
Modem: Motorola SB6120
I'm having problems with my wireless connection constantly dropping and have set the optimal settings from the sticky's in the forums, nothing has changed this problem.
-Have changed to a empty Channel. (8)
- TX and RX packets dropping, also some errors.
-All new CAT 6 cabling between router and modem.
-Have tried all different wireless modes.
-Wired clients are working perfectly.
-Changed the DNS servers.
View 9 Replies
View Related
Feb 1, 2013
Region : Canada
Model : TL-WR941ND
Hardware Version : V5
Firmware Version : wr941nv3_en_3_13_9_up(120201)
ISP : Teksavvy
This wireless router keeps freezing. It might stay up for 6 hours at the most, then I have to reset it or unplug for 10 seconds to get it to reset. I updated the firmware a few months ago thinking this would solve the problem. It hasn't.
View 2 Replies
View Related
Feb 16, 2013
Region : Poland
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120522 Rel.23978
ISP : Orange/TPSA
On my router TD-W8951ND constantly there are the same type errors, while using computer conected to the router:
Code:
2/16/2013 17:24:8> netMakeChannDial: err=-3000 rn_p=80544b08
2/16/2013 17:24:13> Last errorlog repeat 2 Times
[Code].....
View 1 Replies
View Related
Jun 27, 2011
I have a toshiba a215-s7437. I bought this router upgrading from the usual netgear router that everyone and there mother has(wrt54g or something?). The routers are in the same exact spot...less than 6 feet from the computer with no obstructions. No matter WHAT i do, even if i put the router on top of the laptop keyboard, over time, usually a matter of minutes, it starts dropping my link speed. My old netgear ever went below 54, EVER. Even if i was out on the porch.It will connect at 54 mbps, then go to 36, etc etc until we get to 1mbps. I have had other friends bring laptops over, same exact thing happens to them. I am viewing the link speed through windows task manager to get these readings. Though i can't see the link speed on my android phone or xbox, it seems over time they get slower also. I have tried googling the hell out of this issue to no avail. I do have the latest firmware. I have also tried searching these cisco forums and have not found any topics pertaining to this (maybe i just suck at searching). I have comcast at 15mbps and i do know that whether it is 54 or 36, it's not gonna be any faster. But just the fact that it falls the whole way to 1 is not acceptable. My fix for this at the moment is just disconnecting and reconnecting real quick, and i always start back out at 54 mbps. Sometimes I will get lucky and it will stay at that point for 20-30 min?
View 8 Replies
View Related
Feb 16, 2011
I setup a D-Link DIR-825, VB1, Firmware V2.00NA about a month ago. We have 3 Macs here at home - 1 brand new iMac, a G4 Powerbook, and an old G4 / 933 Tower. The G4 tower is connected via ethernet. The other two through Wi-Fi. My problem is that I can barely use the internet for even a few minutes on the G4 tower, connected via Ethernet, without losing my connection. I can be in the middle of loading a page or an image, and suddenly it will say "Waiting for xxx.com". Then if I try to go to Google.com or something I will invariably get "Looking up xxx.com". The connection usually returns on it's own, but it can take up to 3 or 5 minutes. When I get this message on the ethernet G4 tower, I will also have lost connection on the wireless Macs. For the first couple of weeks the tower was not connected and we were just using the two wireless Macs, and they were working well. It seems that as soon as I hooked up the G4 tower via ethernet, connections became very flaky and intermittent all of a sudden.All the Macs are configured for DHCP. We have a Time Warner cable modem. The G4 tower had previously been used at my office with it's own dedicated DSL modem / router, and it worked flawlessly for months at a time without dropping a connection. I've tried rebooting the modem, then the router, then turning all the Macs back on, several times. Same result. I just tried loading the new firmware but it didn't work. Said the Gateway was too crowded or something.
View 1 Replies
View Related
May 13, 2011
I have the Dlink DIR-655, Rev-A, HW 1.35NA Wireless Router Before you ask, I have reset the router to factory defaults, and reinstalled the latest firmware twice, most recently after trying everything else I could think of.I have Cable internet, ALWAYS using wireless, NEVER using wired except for the router installs, which worked just fine until I switched from my old D-Link router to this 655 one a few weeks ago.Now, very frequently, I will open ANY webpage, and the internet will lag, 5, sometimes 10 or 15 seconds and then suddenly it will work properly for a while... only to happen again a little while later - completely randomly it seems.I wired the router to the computer to check to see if the lagging still happened, and everything was fine.I am using a 1-year old Dell laptop, using Windows 7 Home Premium, 64 Bit, and the Network Adapter is Intel WIFI Link 5300 AGN with the most up to date driver confirmed. Under the Advanced Tab for the Laptop's Network Adapter, the settings are as follows:
802.11n CHannel Width for band 2.4 - Value: 20MHz Only
802.11n CHannel Width for band 2.4 - Value: Auto
802.11n Mode - Value: Enabled
There are a number of other settings which I am confident are not relevant, but happy to provide The last setting is: Wireless Mode - Value: 6. 802.11a/b/g In the DLink Configuration, the relevant settings are:
802.11 Mode: Mixed 802.11N and 802.11G
Wireless Channel is on 10, so as not to use the most common "11"
Channel Width Auto 20/40MHz
DNS Relay Enabled
DHCP Server Enabled
Range: 192.168.0.100 to 192.168.0.199
[code].....
Under WAN, the Primary DNS Server numbers are showing and the Secondary DNS Server numbers are showing as 0.0.0.0 McAffee Anti-Virus is up to date and shows no viruses, nor to the Dlink Logs - McAffee Firewall is turned off, Enable SPI in Dlink Settings is turned on.this problem only occurred when I switched routers recently, the old DlInk router I had never had this issue. And I am using a completely different network name with this new router to avoid any conflicts there. And this problem does NOT occur when hardwiring the laptop to the router directly, it only happens via wireless.Storage of the router is fine, it is in the same spot as the old router was, not to hot, not too cold, it didn't eat any metal for breakfast and there are no MRI machines within 10 miles.
View 2 Replies
View Related
May 26, 2012
I've been having issues with my DIR-655 - the speeds are super slow. In the past, I've been able to restart the modem, and my speeds would be acceptable, but now a restart doesn't change the speeds I'm getting from speed test.net. I know it has to do with the router, because when I directly connect to the modem, my speeds are great.
-Speeds WITH router:
-Speeds WITHOUT router:
And like I said, in the past I could restart the router, to get similar speeds to just my modem, but it doesn't work that way anymore.
View 1 Replies
View Related
Aug 16, 2011
Now that the DCS-930 has a dedicated board, we can restart our firmware wishlist.
View 14 Replies
View Related
Dec 15, 2011
I notice that SPI is disabled by default on the DIR-600 (in firmware 2.10 and 2.11 as well).Port forwarding still works with SPI on (use it for BitTorrent).So why is it off by default?Does it slow down things?
View 1 Replies
View Related
Apr 1, 2013
Region : India
Model : TL-MR3020
Hardware Version : V1
Firmware Version : 3.14.2 Build 120817 Rel.55520n
ISP : HNS/Instanet (Cable Internet)
I am using the Router in 3G/4G mode, with WAN only (PPPOE) enabled. I have set a personal SSID in the Wireless > Wireless Settings > Wireless Network Name field.
I do not see the particular SSID on my computer, instead on every reboot / restart of the device a random SSID is generated. see attached screenshot. I can connect and everything works well, but I have to enter the WPA key after each reboot.
View 2 Replies
View Related
May 17, 2012
I have few inter-AS and Hub & Spoke MPLS L3VPNs up and running but, all of them uses plain IPv4 on the PE-to-CE connecting interfaces for switching the L3VPN customer traffic. While, this is ok to route traffic between customer sites over a ISP backbone using the VRF and MP-BGP/LDP configurations which does the MPLS forwarding in the ISP backbone, i would like to know, how to enable MPLS forwarding on the PE-CE links as well to make it MPLS right from CE1 - PE1 - P - PE2 - CE2 all the way for the VPN traffic.
This way, even the last mile access to CE devices will be an MPLS link over a Ethernet PHY so that, the traffic originating from CE1 to CE 2 will be carried on a MPLS tagged Ethernet frame instead of IPoEthernet frame.
View 7 Replies
View Related
Jun 2, 2012
Why does my D-Link WBR 1310 Router constantly need rebooting? By rebooting I mean unplugging power source for 10-15 seconds then replugging it. This problem has been going on for the last 2-3 months.
View 3 Replies
View Related
Oct 29, 2011
I had an old belkin router and the net worked fine well the router would need to be restarted every week or so. But i got an upgrade and i now have a TP link TD-W8961ND The net is terrible its either there or not. have to keep refreshing pages ect .Could a setting possibly be wrong?
View 1 Replies
View Related
Jun 13, 2012
I am having a very frustrating issue with my wireless D-LINK 615 (firmware 5.0.1 NA). The internet connection drops constantly every 2-3 hours. Here are the settings on my router:
Cable modem
Modem Motorola Surfboard model SB6120
Code...
This seems to happen after I upgraded the firmware. Before that, did not get a complaint from my children or wife. Before I squeeze the last drop out of this lemon.
View 3 Replies
View Related
Jul 23, 2012
I'm watching a video streamed from my laptop and the signal is constantly being dropped. I suspect the D-Link DES-105. I have another Ethernet switch on the system as well but it is a Gigabit unmanaged switch from D-Link and has worked well with video streams. I've removed the DES 105 from the circuit and videos play fine. Should I dump to DES-105 for another Gigabit switch? SOme say I have a bad cable somewhere but I have tested all and have not found a problem.
View 2 Replies
View Related
Feb 22, 2012
My Access Point Power Led blinks constantly, Lan led works normally, Wlan led never turns on.
Access Point: D-Link DWL-2100AP
View 6 Replies
View Related
Feb 6, 2012
I have 2 computers connected to the router (via cable). The problem is that have to reboot the router several times per day because one or both computers lose their internet connection. This happens regardless if one or two computers are turned on.
Router: DIR-615
Firmware version 4.00
Hardware version: D1
Computer1: Win7 64
Computer2: Win Vista 64
View 15 Replies
View Related
Jun 6, 2012
One of Cisco Wireless AP 1242 installed in my premises restarts itself; AP is getting power from Catalyst 2960 POE. I am using multiple SSID on this AP. I have issued the show tech-support. I have seen below in tech-support System was restarted by unknown reload cause - reason ptr 0xF, PC 0x46FEB8, address 0x0? what could be the reason of restarting of AP. AP is in production since 1 year and it restarts seldom.
View 2 Replies
View Related
Jul 25, 2009
Is there any way yo restart the WRT160NL from the web interface? I've had several routers before this Linksys and all of them had this option. In the web GUI of the WRT I can't find the way to do it and I have no other solution of unplugging it and plugging again.
View 6 Replies
View Related
Apr 6, 2013
Im using WLC 2504 with vertion 7.4 and 2600 LAP's the access points are working fine when its isolated from the live network, but once its in the live network the AP radios resetting (APs won't reboot) and unregistering from the WLC in random intervals,
WLC error log is as follow,
---------------Show msglog---------------
Message Log Severity Level ...................... ERROR
*emWeb: Apr 05 14:57:02.966: #APF-0-SITE_OVERRIDE_CONFIG_RESET: apf_site_override.c:400 Resetting site override config.
*Dot1x_NW_MsgTask_6: Apr 05 14:50:14.444: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 20:10:7a:1a:60:9e - got 00 00 00 00 00 00 00 00, expected 00 00 00 00 00 00 00 02
[code].....
View 1 Replies
View Related
Jun 4, 2012
i have 2504 series controller and today its stuck (before was working fine) when i restart it (remove power and power on again) its stuck here (see in snap)
View 4 Replies
View Related
Jan 29, 2013
I am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. All LWAPP which are up for more than 200-300 days has to be rebooted, this problem is with all AP's. clients are not getting connected,after reboot they work fine.how do the same from ncs.
View 5 Replies
View Related
Feb 16, 2013
My keyboard was broken so plugged in a USB keyboard that doesn't have a fn button. I must have accidentally pressed something as my comp is asking me to turn in the wireless capability. There is no button on the computer and the light for wifi is off. How to turn this back on with a keyboard that does not have a fn button?
View 1 Replies
View Related
Aug 9, 2011
I bought an 871w second hand with 124-24T IOS on it. I would like to enable QoS. When I use Cisco Configuration Professional to manage the router I click on QoS and it says it is not available. I know that the router itself is QoS capable.
This is my first time dealing with a router such as this and I wonder what I need to do to enable QoS.
View 1 Replies
View Related
Apr 10, 2011
My mom has a Toshiba laptop that she got for Christmas and a lexmark all-in-one wireless printer. Every time she tries to print something to the wireless printer, the item just stays in the printing queue. However, once she restarts her laptop all of a sudden the laptop and printer seem to communicate, and the printer always starts printing whatever was in her queue from the previous time.so when she wants to print something it automatically starts printing, and she doesn't have to restart her computer every time to print stuff.
View 2 Replies
View Related
Mar 16, 2012
I haven't really allowed this to bug me too much, but I went over by a friend's house, used his WiFi, closed my Laptop, it disconnected, I reconnected to his network, came back home, now every time I restart or Shutdown my computer I have to reconnect, not that big of a deal
View 5 Replies
View Related
Jan 30, 2010
My WET610N crashes when I'm using it behind my PS3 while I'm watching videos in DLNA with the PS3 Media Server. Sometimes I can watch it during 1 hour without problem, somtimes it crashes and restart after 10 minutes of playing already. The restart is taking quite a long time, something like 2 or 3 minutes to get back to a Wifi connection. The router is still working properly while the WET610N is restarting.
The firmware is the latest 1.0.03, the settings are made for Video Access mode. I'm not using any encryption, only MAC address filtering.
My Wifi router is a Belkin N+ (F5D8235-4 v2000).
View 6 Replies
View Related
