Dell :: V305W Wireless Printer Not Connecting
Jan 13, 2010
I have had this printer for a while now and I was using it with a Aciontec DSL wifi modem. It connected just fine without any problems via the installation software and a usb cable to initalize. I just swtiched from DSL to a Cable setup. I am using a Motorola "surfboard" SBG901 with built in wifi. It came pre installed with a WPA PSK string. Every time I have tried to connect it would not accept the WPA PSK string and being a legit 8 -63 charcters. I messed around witht he Cable modem settings and eventually decided to turn off all proection for a second to see if I could connect. Sure enough I was able to connect. In my Cable modem settings I have WPA/WPA PSK/WPA 2/WPA2 PSK . When you select either WPA or WPA2 it greys out the WPA PSK and WPA2 PSK selections and vice versa. I am using WPA PSK currently. I tried to switch to WPA but the passcode section was greyed out and had some "radius key section". I am not too familar with network settings just the basics. I used the Dell Wireless connection utility and tried setting up a manual connection by putting in the ssid and what type of protection but it still would not accept the passcode as being a WPA.
View 13 Replies
ADVERTISEMENT
Nov 5, 2012
I have a 2 year old v305w printer i want to use with my new imac and ipad. Its perfectly good and dont want to throw it out. Are there drivers available to make this compatible with air print on my ipad and imac?
View 2 Replies
View Related
Sep 14, 2012
I have a new inspiron 15 laptop and also bought an all in one wireless printer. I have a iinet BOB lite modem. I cannot for the life of me figure out how to get the wireless printer, modem and laptop to tall to one another. Am I missing something or should it all work? The laptop has internet access. The laptop also shows the printer installed with a big green tick next to it but it says it is offline. At no point has a green light appeared on the printer to indicate any wireless connectivity to the modem.
View 2 Replies
View Related
Mar 11, 2011
I have just bought a v313w printer & cannot get it to connect wireless to my inspirion 1545 laptop (windows 7)During the wireless set-up, it gets to the third of the five stages ok. These are configuring printer, resetting printer & connecting to wireless network. It fails on Acquiring network address & communicating with the printer!
I have tried the following without any luck, uninstalling & re-installing, powering down cable modem/router, changing security settings on router from 64bit wep to 128 wep & WPA/PSK, dell expert taking control of my laptop & trying to connect (which resulted in Dell sending me a new printer because the expert seemed to think it maybe a faulty wireless card in the printer, this is not the case becuase the same problem occurs with the second printer dell have sent me!). I have downloaded & installed the latest drivers for this printer from the dell website & I've switched off my security (anti virus/firewall) when trying to install.
I am completely stuck as to what to try next, the printer works perfectly fine from the USB cable.
View 2 Replies
View Related
Sep 27, 2011
I have a new n series Belnet wireless router that can take a usb printer. I have a Lexmark 2200 Series 1 Printer (with usb connection). I have used this printer with my laptop (runs Windows xp) by connecting the printer usb directly. I have also connected my laptop to the wireless router. I have plugged the printer into the wireless router's usb port. Is it possible to access the printer this way? I do not know what I should do next. The laptop cannot access the printer through the wireless.
View 5 Replies
View Related
Jan 18, 2013
We have printers connected to the network, but I need a standalone printer connected to my workstation due to the confidential nature of some of my printing.I chose a small wireless printer as I already am being strangled with wires and cables.I went thru the wireless installation, and was told to connect PC to printer via USB.I finally got a connection, but not the one I wanted. We also have a wireless router, but connecting to itI got message saying "a connection was made but your PC is not connected to your printer".
View 5 Replies
View Related
Jun 26, 2012
I have a iP4820, Canon printer that has a USB port and a pictbridge port. It is currently connected to my desktop vis the USB port. Is there anyway I can connect the printer to the Belkin wireless router so that I can print from my laptops as well as my desktop?
View 1 Replies
View Related
Jan 4, 2011
Have a non-wireless printer (HP F4280) and non-wireless Desktop (Dell Dimension 2000). Just added an HP G62 wireless laptop and Cisco Valet+ router. My problem is I want to make the printer wireless but their is only one USB port and no ethernet port. If I put an adaptor into the USB port on the printer to make it wireless, I will of course loose access from my dektop. Can I put a splitter into the printers USB port and use an wireless adaptor plus the cable to the desktop?
View 5 Replies
View Related
Sep 10, 2011
Have three computers ( 2 are XP one is vista) connected via wireless router one computer is considered a host computer sitting on a docking station which has the printers connected to it. In the beginning once everything was connected we could print from any computer wireless, then one day we had a power outage and for some reason we can only print from the host computer. How to get the other computers back online to print. All computers are still able to connect to the internet via wireless router (Linksys E1000) but not able to print except the host which is directly connected to the printers.
View 3 Replies
View Related
Nov 26, 2012
I can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router?
View 2 Replies
View Related
Jun 21, 2011
I had been using my printer through my linksys router with no problem until I added a password to the linksys. Now I can't print. My computer says it can't "ping" the printer.
View 1 Replies
View Related
Apr 1, 2012
I managed to connect my USB printer (and tested ok) through the E3200 router using the Cisco Connect programme on Windows 7. I note that there was an option for a USB Printer connection in the set-up screen.
When I tried it on the Mac using Mac OSX 10.7.3 and Cisco Connect Ver 1.4, I noted that there was no option for a USB Printer connection.
View 3 Replies
View Related
Apr 11, 2011
I think I have worked out that you can`t currently connect a usb printer to the usb port on the e4200 in order to share it over the network.
However I have heard reports that this might facility might be enabled in the spring.
I have also heard something about `virtual usb` but I don`t know whether this has anything to do with it.
View 9 Replies
View Related
Jul 26, 2012
Just purchased an E900 wireless router and cannot figure out how to connect my Samsung wireless printer. The printer has a WPS button, but the router does not. The router wants me to input information into the Samsung printer, but the printer has no screen, and I cannot find a place to input the router info anywhere in the Samsung software. I am going crazy here...I'm not a techie, but I'm also not a complete technology idiot.
View 2 Replies
View Related
Mar 3, 2013
I was wondering if there was a way to connect a wired printer to my linksys E3000? or am I still stuck with using my spare desktop.
View 4 Replies
View Related
Nov 26, 2011
I have a BEFW11SF V4 firmware version 1.52.03. I just bought an HP DJ3051A and can't get it to connect. HP support says I need to change a setting to mixed mode but I don't see that I can. Does this router supports mixed mode and if so how do I change it?The other comment the HP rep made was the printer does not support Wireless N. I am fine with this since the router says Wireless B. It seems based on the HP rep's comment that as long as I am not using Wireless N, then I should be fine.
View 1 Replies
View Related
Nov 27, 2012
I can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router? Any other ways to access this printer from my PC which is connected to LAN via ethernet?
View 1 Replies
View Related
Jan 13, 2012
Set up Dell 310 wireless printer to Fedora 16 OS
View 1 Replies
View Related
Oct 14, 2011
My V715w printer works on USB. How do I get it setup as wireless? I have followed all the suggestions in the book, my network works super for both my computers, but it won't recognize the printer will not recognize my network?
View 1 Replies
View Related
Dec 16, 2012
Had to change my wireless box and now my wireless Dell V505 cannot communicate with the new box. Unable to print.
View 1 Replies
View Related
Feb 22, 2011
I switch to a new internet provider. which is wireless[Frontier]. my printer is dell V715w the orange light is flashing. provide detailed info to correct
View 1 Replies
View Related
Apr 4, 2011
I have a Dell Inspiron E1505 running windows xp. Also an HP Photosmart C6180 wireless printer. This happens every time I move. I get the computer on the network and the printer on the network but they don't talk. I can't ping the printer and I can't bring up the embedded web browser. I can print the network config page from the printer but can't print a test page from the computer.I've disabled my firewall. That hasn't worked. I've tried creating a port especially for that ip address. However I don't have the disk for the printer and when I had to select my product, it only showed the C6100 series BT. I don't know what BT means but I selected that. I don't know what that means but it still won't print. The printer shows up in my printer and faxes menu but when I ran the HP print diagnostic utility no printers were displayed.
View 1 Replies
View Related
Sep 26, 2012
I bought a Dell V525w printer. Once I set it up, my computers can no longer access the internet! I have looked everywhere and cannot find an answer. The only way I can make the internet work again is to power down the printer, and reset the router. But, as soon as I turn the printer on, the internet conenction is lost again. This is very frustrating. I need to know how to fix this as soon as possible.I have a Netgear WNDR3700v3 wireless router. My computer is an Alienware X51.
View 1 Replies
View Related
Oct 11, 2011
We have a Brothers 7820N Printer and would like to connect it to our wireless network.
View 1 Replies
View Related
Jan 23, 2013
We have a Verizon T1 line providing internet for our backoffice network. On this network, we have 4 network printers that are shared between the facility. We recently opted to go with new web based software that neccesitates a high speed internet connection, and 12 wireless devices across the building. We signed a contract with Comcast Business Class internet, so that in the event of an external failure with one ISP, we would have the other offer redundancy with the new wireless router.It has now become clear that our nurses that are on the Comcast wireless network, now need to print from their wireless devices regularly. At the time this is obviously not possible, because the network printers are only on our backoffice network. Buying a wireless inkjet printer is out of the question. How can I make this happen? All of the printers have a local static IP on our backoffice network (Verizon). I have heard of software that will essentially send the print job to another computer, which would relay the print job to the designated printer.
View 1 Replies
View Related
Jul 1, 2012
So basically I need to hook up a HP LaserJet P2015 to a business and home network. LaserJet P2015 user guide. I would like to keep the printer's ip static so it will stay the same on each network individually. am using a business router (Linksys RV120 W Wirless-N VPN Firewall) with two VLAN (business and home network) built using this router. Also I have two access points both being used to expand this signal through out the building, but not as an extender. They are two Linksys WAP54G access points. The access points are used to expand the home network, and not the business network.
View 1 Replies
View Related
Jul 13, 2012
I have; iMac connected to Netgear DG834G router with ethernet cable and epson RX620 printer connected with USB cable/ Laptop running windows XP Media edition which connects ok to network and printer works ok too.Now have new HP desktop running Windows 7 64-bit. I have tried installing vista driver for printer, as per epson site,but I cannot get the printer to work wirelessly over the network.
View 3 Replies
View Related
Mar 14, 2012
My problem is when i try and connect a printer from windows 7 that is connected to a local pc via usb onto a remote desktop it doesnt connect but when i try and connect from wins xp it does. On the remote desktop i click to add a printer and then i select network printer. Then i type\ip-address-of-pcprinter share name. It says it cannot connect to printer but when i try this method on an xp computer it accepts it.
View 6 Replies
View Related
Nov 26, 2012
i have 2 printer one is connected through usb, i want to connect one more printer through lan using switch....how to connect?
View 3 Replies
View Related
Mar 21, 2012
I would like to know how to install and connect my HP laser jet p4015n
View 1 Replies
View Related
Apr 23, 2012
Currently I have 2 different modem running in my working area which is modem A and modem B. Whenever user from Modem A(192.168.0.1) or Modem B(192.168.0.10) would like to print or scan something using the shared printer, I need to manually plug the cable into either Modem A or Modem B depends on the network the user are currently using.How I do previously is only set DHCP on Modem A and disable DHCP for modem B so that Modem B will share DHCP assigned by Modem A. Both modems connect to the same Switch with the printer cable so both network user can use it together.But the problem now is I have to enable DHCP for both modems and causing the previously method can't be use anymore. So is there any other way that I can link both Modem A and Modem B with each assign different DHCP to link with 1
View 5 Replies
View Related
Oct 29, 2011
I'm having issues connecting a HP 9000dn printer to my home network. I have windows 7 x64 with a Belkin wireless router. I have the printer (via a jetdriect 615n driver) connected to my router and the computer will not see the printer. I'm a newbie to networking
View 3 Replies
View Related
Dec 20, 2012
N750 DB USB printer not connecting. I'm currently running a Canon MP480 multi-purpose printer connected through USB to the N750 DB router. I have both the printer driver and Belkin USB Print and Storage Manager software installed on a desktop PC that connects wirelessly to the router. The Belkin print manager software "sees" the printer, but when I try to connect it says please install printer drivers. I've installed and re-installed these drivers a few times, with no effects.
View 14 Replies
View Related