My laptop, which is a gateway, not sure which type but it's relatively new. just a few years old maybe 5 at the max? idk tbh. Anyways when my mom first gave it to me it had an internet problem. Said limited connectivity and would not connect. Someone told me to restart the computer and the internet magically started working again. It didn't work this time.
View 4 RepliesI can't connect to the internet using our wireless router. The signal is excellent but there's a yellow triangle with an exclamation point. It says that there is limited access. I tried resetting the router, checked all the plugs, restarted my laptop., all to no avail. I tried connecting using my phone, and I can go online so the problem lies with my laptop.
I checked my device manager and under Networks, the 6TO4 adapters has a yellow triangle with exclamation point. With a code 10 error. I tried to run 'check for solutions" but I can't connect to the internet. Using my phone, I saw websites dealing with the same problem. I uninstalled all the 6TO4 adapters along with the isatap adapter because it also has the same problem except that it's reporting error 31. Then I restarted my laptop.I can connect to the internet but only through LAN. I still can't connect through my wifi. I tried to reinstall the 6TO4 and isatap but it still shows the same message.
Just bought a new Cisco e1200 router last week. When i first hooked it up, it was giving me extremely low (significantly lower than my old router) downloading speeds. After switching the networking mode from "mixed' to "Wireless-G only", the speeds went back to normal. I tried "Wireless-N only", but it didn't work after that. Seemingly, my computer does not work with Wirless-N?
It's been running okay now, but 2 things happen occasionally: When playing a game, I experience lag for a period of 5 minutes, or sometimes 20 minutes. It goes away on its own. Never happened with my old router. When surfing the internet, pages will refuse to load. The connection bars shown at the bottom right hand corner of my computer display a yellow triangle with an exclamation point. This goes away on its own after about 4-5 minutes. These problems come randomly every 3-4 or days, maybe a bit longer.
I tried to plug in the internet cable in my laptop i kept getting that yellow triangle with an exclamation mark on it (down in the right). i kept plug in and out the cable until i got connected. i use a cable/dsl router, having 2 computers connected in the same time. only mine gave this error, as the other ran perfectly in the meantime. what seems to be the problem? a virus/trojan?
View 1 Replies View RelatedMy wifi used to run fine. Now there is a yellow little hazard sign next to the wifi bars and the PC says: Limited connectivity to belkin.758". I cannot connect to the internet!
View 3 Replies View RelatedMy internet just keeps dropping every 15 minutes or so. I never really have a problem, but for the past week or so I have been having this issue.I don't think it is just wireless though, because my xbox live connection keeps dropping too and that is wired into my router.
If I right click on my connection and click "Status", this is what I get.
IPv4 Connectivity: Internet
IPv6 Connectivity: No network access
I have unplugged my router and modem at least 10 times. I don't know what else to do.
I've been having a kind of weird situation with a laptop here at the house. Once in awhile it will decide it doesn't want to connect to our router. No matter what I do (system restore, restart the computer, disable/reenable the network adapter, rollback driver, reinstall driver, etc) it won't fix it. What does fix it is connecting to my neighbor's unsecured network, then reconnecting to my router. It's an easy fix but I am puzzled as to why it behaves like this? Another thing that may or may not be related is when I go into Device Manager and Network Adapters, there were two ISATAP adapters with a yellow exclamation point over them. I ran a fix from Microsoft that said it reinstalled the drivers, but when I go into Device Manager the problem ISATAP adapters (two of them) are no longer listed. I'll see if this solves the random connection loss and inability to reconnect issue.
View 1 Replies View RelatedI am frequently disconnected from the internet, I would say about every 30 minutes.. In the bottom right of my screen where the internet connection thing is it has a yellow triangle with an exclamation mark on it and says "no internet access"
View 19 Replies View RelatedWhere internet connection strength is shown in main screen there is a yellow triangle with a black exclamation Mark in it covering the signal strength icon. I have tried contacting my Internet provider who could not fix. They have sent a new modem but still same issue on pc. I have several games consoles and also have an iPad and iPhone and Internet is working on these however my neighbour tried to use her laptop in my house and has the same issue.
View 1 Replies View RelatedI just recently bought a linksys E900 wireless-N300 Router. I installed the software on the disc and followed the on screen instructions. When I attempt to use an ethernet cable as I did with my last router, it won't work. I get that yellow triangle icon indicating no internet access. I tried using a wireless hub to connect wirelessly...I connect, but no internet access. My PC knows its there, suggests that I reset the modem, doesn't work.
View 8 Replies View RelatedMy wireless internet goes off and on. The yellow exclamation comes up. It last for several seconds and then does it again if I try to load several web pages at once. When I run the diagnostics, Windows says it "fixed" that the Default Gateway was not available. Is there something on my laptop that I need to change as far as settings are concerned because it works some of the time but not all of the time. It seems to stop working when I try loading youtube videos.
View 14 Replies View RelatedI have the M2N32-SLI Deluxe/Wireless Edition motherboard with onboard wireless. I built this computer myself. I did a fresh install of Windows 7. I installed the wireless drivers from the asus website by putting them onto a flash drive from my laptop and installing them on my desktop.On my wireless signal, I get the yellow triangle with a ! in the middle. Nothing else has been installed. I am at a loss of what to do to get rid of this and just get my wireless to work. We have 3 other laptops and one other desktop that work fine with no issues, but this one desktop seems to have problems.
View 10 Replies View RelatedI think my computer is infected with malware right now. It is heating up quickly and I'm seeing ads in text in websites that don't do that (cbc, reddit, wikipedia).I had this issue a couple of months ago but Spybot seemed to fix the issue.Recently I noticed my computer was heating faster (and hotter) than usual so I ran a search and it said no threats were found. Not too longer after I start noticing the ads again so I know there is a problem. I have ran the search twice since then and still nothing. I was advised to use ccleaner,malwarebytes, and Super Anti-Spyware. It removed one other threat but the problem was still there. I then started using combofix, but I did not like the look of it so I stopped that scan. It seemed a little sketchy.
My old laptop (the one I'm on now) and my girlfriend's laptop work fine. I connected it with the Ethernet cord and that didn't change anything.I have Windows 7. It's on a 2010 Samsung (I'm not very tech savvy so I'm not sure about all the other details). I primarily used Firefox, but I just switched to Googlechrome this week (well after the problems began).
I updated my graphics card driver and when I rebooted, the wireless wasn't working. I went into device manager, and all the network adapters listed there had a yellow exclamation mark beside them. Attempts to disable/enable and uninstall/reinstall haven't worked. I'm at a total loss. I've tried system restore but it failed, and I've tried reinstalling the graphics card driver update, but that hasn't worked either.
View 1 Replies View RelatedMy Desktop (Win 7) and laptop (Acer Aspire 4830T) were talking both ways (after I fixed a Teredo Tunnel problem!) but have now degraded to the point where I cannot setup a Homegroup.The main issue is that although my wireless internet works when I am home (D-Link DIR-615 router), as soon as I leave, I get the dreaded Yellow exclamation on both Virgin Trains and my client's Unsecured wifi (with password protection). These did use to work in July. Can't detect an event when started to go wrong, though could blame Windows Update! Did try System Restore but these keep failing. Using Kaspersky.
[code]....
Ok BEFSR81 (192.168.1.1) is connected to the Modem. I have a cable from one of the BEFSR81's LAN ports going to WRT54G (192.168.2.1) WAN port. My computer is connected to the BEFSR81. I can not access the setup page (http;//192.168.2.1) from my computer, maybe I am not suppossed to be able to do that. The Laptop sees a Linksys wireless connection, but there is a yellow exclamation point over it.
View 7 Replies View Relatedmy router is sitecom gigabit 300N. since the past week there is this yellow exclamation mark on the connection in the task bar, near the clock. if I pass the mouse over it, it says no internet connection, eventhough I'm connected to the internet and I'm writing this right now, this is on desktop pc and connected to router by cable. the same thing on my laptop that is connected through WiFi, the signal strenght is normal, but there is the same exclamation mark. I'm pretty sure its the router not the PC because this happens on two different machines with the same router. I tried turning the router off and left it that way for about 7 minutes but that didnt work. is there something in settings I should do? or throw it away and buy Linksys/D-link router?
View 6 Replies View RelatedI'm having problem with the router WRT54G2, My laptop - winodws 7- connetcs to the wireless.Then it asks me if I wanna configure the router I saw yes, I give a name to the wireless connection and a password, everything works and come to the end, after that I connect to my wireless connection and a little yellow triangle appears -down right on the signal bar. I resetted the router already and update the firmware.Still won't work. I thought maybe I need to put a static IP but I won't find the DSN Code.
View 1 Replies View RelatedI have several E4200 routers deployed in our library district. In one branch, we have been having sporadic problems with computers not being able to maintain a connection. Typically the computer will connect and then the connection will drop and Windows will display the yellow error triangle on the wifi signal strength display.I have swapped the router with another brand new E4200 with the latest firmware but am still having this problem.
View 6 Replies View RelatedI can find and connect to the wireless network in our house, but it has the yellow triangle with an exclamation mark. My housemates are on the internet fine on their laptops and my xbox live is working, so it's clearly an issue with my laptop. My laptop's internet evidently works with an ethernet cable too, but I can't just go through an ethernet cable all the time since the router is in a housemate's bedroom.
View 14 Replies View RelatedI have a exclamation point and no Internet access over my connection. Ever time I move the mouse the swirly thing is moving like something is trying to load. I have reset the windsock. I have restored to an earlier date. I have tried in safe mode with metworking. I have tried with all firewalls off (windows and mcaffe). The router seems fine because all our devices r running off of it. I tried to connect with the computer wirelessly and that doesn't work.
View 1 Replies View Relatedi'm using win7 and linux mint in my laptop. when i'm on linux i 'm able to connect in a specific ssid with my b43 driver. when i switch back to windows(broadcom a/b/g) i can not connect to this ssid-there is a yellow mark with limited connection. what do you think? is this a driver problem with win7. or win 7 driver has ''less power'' than linux's?
View 2 Replies View RelatedSetting up my wifi network with an old BEFSR41 Router and WAP11 wireless access point. Have laptop with XP Pro that connects just fine without encryption but as soon as I try to use WEP I get the "Limited or no connectivity" error. When prompted, I type in the same passphrase as the one I used for the WEP 128bit encryption while setting up the WAP11 for my network.
View 4 Replies View RelatedI have a modem connected to a router wirelessly and an access point few computers have access to the internet and some has limited access even those close to the access point.
View 2 Replies View RelatedI am using the cisco linksys E1200 WiFi router. when ever I connect my laptop to WiFi, its show Limited connectivity/Yellow Caution sign when connected.
I try to reconfigre it & also in factory default mode it show same.
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View Relatedwhy it's not included in the setup of the router ? I can only see (GMT+04:00) Armenia and nothing else !!
View 1 Replies View RelatedAbout 10 months ago I got a new computer, with it I got a the Linksys AE1000 wireless adapter. At first all was fine, no blue screens. About a month after I got all my game and such installed (I am a bit of a gamer) I started to get bsod error 0x0000000D1 in the middle of my game. I wasn't sure the cause of the problem, so at first I ignored it. I started to get the same error more and more frequently and the same cause of the problem. I believe that the wireless adapter is the cause of the problem, but alas I can never be sure..
View 14 Replies View RelatedI had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View Related