Linksys Wireless Router :: WTG54G HP AIO Wireless Usage
Mar 14, 2012
I tried searching here for this info but couldn't find exactly what I'm looking for. I have a Linksys WTG54G router. I'm trying to connect a HP AIO Wireless printer. I thought I had it right when I went into the routers setup page and assigned what I thought was a staic Ip (on the setup page where it said static dns 1) outside of the DHCP range. This seemed to work fine.However, when I booted up the next day I had no internet connection and had to undo everything and put it back the way it was.Is there a how to out or guide there with pictures that shows completely how to do this.
View 9 Replies
ADVERTISEMENT
Nov 12, 2012
Why my E3200 is (for lack of a better word) "throttling" my internet speeds.I'm signed up for my ISP's 50Mbps data plan. When I hook up my laptop directly to the cable modem (via LAN cable), I see close to 50Mbps as the internet speed (measure via speedtest.net). When I hook up my router to the cable modem, and connect via LAN cable to the router, the internet speed comes down to around a maximum of 26Mbps. NOTE, that I am still talking about a wired connection and not a wireless access. Speed tests with the wireless access do yield the same results as well. To rule out the obvious, I've confirmed that there aren't any other devices on the network and no other bandwidth hogging applications running while I performed these tests.
View 9 Replies
View Related
Mar 9, 2011
using my wireless router (and my dsl internet connection)?My router is a Linksys WRT54G. I have a Windows 7 desktop, a Windows XP SP3 desktop and a Windows XP SP3 laptop that connect to the router.
View 9 Replies
View Related
Mar 24, 2013
I have a WRT54G routher hardlined to a Ubuntu 12.04 server that is dedicated to minecraft.I have two ports opened for Minecraft to run off of.I'de like to give remote access to the computer to other people to maintain the server.BUT I need to restrict ANY and ALL ability for them to access the internet by either blocking all other ports or something else. Id rather not have to restrict it through Ubuntu if I don't have to.
View 1 Replies
View Related
Mar 19, 2011
How do I know if I'm using 2.4 or 5ghz? I would like the laptop and ps3/net flix to use the 5ghz and everything else to use 2.4ghz. I used the e3000 CD fro the setup. When I was at the last part of the setup, when it gives you a ssid name and password. I deleted it and typed in a name that I could remember. I clicked the button for the next step and everything was complete. I also received another name for guest to use the computer. The e3000 setup just game me some wild name like running water.
I would like to know since I have two different names, which on e is using 5ghz and which one is using 2.4thz? Can you tell me if the e3000 automatically have the first name use 5ghz and the guest just 2.4ghz on the second name?
View 3 Replies
View Related
Mar 28, 2013
I'm thinking of purchasing a Cisco Linksys EA6500. I need a router that can one monitor bandwidth used by device. Keep exceeding our ISP's network bandwidth allocation, need to identify the devices that are causing this high usage and be able to do so from the router. Does the EA6500's standard software support this, is their router software one can obtain for the unit that does this or is there another home router option that can perform this function?
View 6 Replies
View Related
Apr 3, 2013
however recently when i check my internet usage log on my wireless company (Rogers) the usage is totally off from what my bandwidth tracker shows me. So i decide to turn off my wifi and see what happens, there has always been this weird wifi connection appearing whenever my wifi appears, then afterwards when i turn off my wifi the suspicious wifi connections disappear. is this possible that someone is using our wifi? i might just be overreacting but it has brought me to concern that if the usage continues my family will have to end up paying over $30 for extra internet use. it is very frustrating me because when i check my DHCP client table it only shows 3 connection, ethernet - my desktop which is not turned on, 2 wireless connection - my laptop and my sister's laptop.
View 6 Replies
View Related
Apr 6, 2011
I would like to use my WUSB54GC ver2 adapter with a WIN7 ultimate 64-bit PC. Do I have any chance to use it on this computer? Linksys' website says that only ver3 adapters can use the WIN7 driver.
View 3 Replies
View Related
Apr 15, 2012
I just have an experience to relate. I was provided the Cisco DPC 3825 unit for my home by my ISP. I couldn't get a strong enough signal to reach my smart tv about 50 to 60 away from the unit, which is in my office for computer uses. I purchased a Netgear extender to extend the signal. I was having trouble connecting the extender to the Cisco unit and get an internet connection. So I phoned my ISP and was told by the person on the phone that their Cisco unit cannot connect to this extender.
I found out that the Cisco unit was set to hidden by my son. After changing this setting I was able to easily connect the Netgear extender to the Cisco unit and get internet and a strong enough signal to my smart tv.
View 1 Replies
View Related
Oct 22, 2011
Why do I have to keep my laptop power cord plugged in in order to not lose an internet connection? I configured settings for maximum performance in both the adapter configurations and advanced power settings.Could it have some thing to do with my wireless router?I don't experience this problem at wi-fi hotspots.
View 3 Replies
View Related
Nov 13, 2011
I'm having trouble setting up a wireless internet connection for my computers, I connected the patch cable from my modem to a wireless router, then connected to that network with a usb for my computer.I was able to connect to the network, but couldn't seem to actually get into the internet. Is there any solutions to this?
When doing ipconfig /all, the message I get is:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Victors
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
View 1 Replies
View Related
Apr 27, 2012
we have a high speed internet and my modem is capable of wireless what I want to know, is there a way that I can monitor how much my daughter is on her computer and what websites she is visiting without having to install a program on her notebook or having to check her history etc? I would like to be able to do it all from my computer
View 2 Replies
View Related
Jan 22, 2013
Region : Netherlands
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP :
Is it possible to use a VPN service such as hidemyass on the TL-WR1043ND without installing the DD-WRT firmware?
View 2 Replies
View Related
Sep 19, 2012
Is it possible to build two separate bridged connections from one "base"?
I'd need to connect to two other buildings which luckily happen to be quite on the same direction (antennawise). how to configure this into the devices I call "base", "building1" and "building2". The first building is about 50 meters and the other about 120 meters away. 11Mbps would be adequate for both. A some kind of encryption would be needed.
View 1 Replies
View Related
Apr 9, 2012
Just wondering of this model of WAP - AIR-CAP3502I-X-K9—802.11a/g/ is working standalone with out a controller , or is it only controller based ?
View 11 Replies
View Related
Oct 30, 2011
How can I monitor broadband usage of multiple PC's connected to a wireless router/modem?
View 1 Replies
View Related
Aug 20, 2012
What is the average memory usage for a Cisco 5508 with 500 APs (mostly 3502s) running 7.0.116.0 code? I am currently at 450 access points and have 80% memory usage should I be concerned?
View 6 Replies
View Related
Oct 4, 2012
I have cisco 887V (CISCO887V-SEC-K9) router. I am not sure it will work as Access Point or not. It does not have any external antennas installed. I checked on website and found that all Cisco 887V routers have option of Access Point and also found that the software ap801-k9w7-tar.124-10b.JY.tar,can be used for access point.
View 1 Replies
View Related
Apr 17, 2012
What is the operating and/or peak power consumption (in kW) of a 5508 WLC with redundant power supplies?
The below power details are from the 5508 datasheet which lists 115 W as the maximum draw (0.115 kW) however this seems a bit low, is this right?
Input power: 100 to 240 VAC; 50/60 Hz; 1.05 A at 110 VAC, 115 W Maximum; 0.523 A at 220 VAC, 115 W Maximum; Test Conditions: Redundant Power Supplies, 40C, Full Traffic. Heat Dissipation: 392 BTU/hour at 110/220 VAC Maximum Cisco 5500 Series Wireless Controllers Data Sheet: [URL]
View 1 Replies
View Related
Dec 2, 2012
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version : ?
ISP : Guadalupe Valley Telephone Company (TX)
I am a bit of a noobie and am considering buying a TL-WR1043ND router/access point, but I have read that this router will not connect directly to my ISP over DSL.I have fiber optic to my home from a local telephone company. Whether it will or will not act as the gateway to the Internet. If not, does it connect to another router that acts as a gateway to the Internet? Or what?Secondly, do you recommend this model which, considering features, appears to be good value at arount $50, but would like to know what others think about it.
View 1 Replies
View Related
Apr 1, 2012
Is it possible to use this feature on WLC 2504 ? ( Passive client feature). I found just this note :" The passive client feature is supported on Cisco 5500 and Cisco 2100 Series Controllers. "
View 8 Replies
View Related
Jan 13, 2013
Region : Romania
Model : TL-WR841ND
Hardware Version :
Firmware Version : 3.13.27 Build 121101 Rel.38183n
ISP : cosmote
hardware version is WR841N v8.wireless works just fine. i use it for my smartphone and an old laptop. i use ethernet cable to connect to main computer where all is ok until i start using my bit torrent client. as soon as i build up traffic above 1MB the ethernet portion of the router freezes and needs a reboot. when frozen, wireless is still working and i still have access on the lan to the router via my browser. i got this router so i could have wifi for my phone. my old router (asus rx3041) worked just fine and i accessed my isp at the maximum speeds it would allow on a 60 gigabit connection.
View 9 Replies
View Related
Feb 7, 2013
I have a small Network at my office, all done by myself with my limited knowledge. I have 9 systems connected thru physical LAN and 1 laptop connected through Wireless (from my internet router)I have distributed the internet connection openly, not using a proxy server. Anyone plugs in will get Internet on their system through the DHCP.Recently I found that internet usage been crossing the limits.sniff/monitor internet/bandwidth usage system wise.I have a internet router (Linksys/Cisco WRT 120N) from which the cable goes to an un-managed 8 port switch.I have three different areas in my office, so I pulled single cable to each of these areas and there I used another un-managed 8 port switch to distribute the LAN to the systems.
View 3 Replies
View Related
Nov 11, 2010
When i download alot (around 400-700 kb/s) or upload ( around 100kb/s) the router stops responding, for every connection. LAN WAN WLAN, all stop responding... active connections though remain connected but visiting new sites/pages is not possible...
plugging out the power for 10 seconds and booting it up again..
View 9 Replies
View Related
May 3, 2013
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 22.05.2012
ISP :
I have a TD-W8951ND v5 on the latest firmware.
I recently broke my broadband data cap which surprised me as I had not been using the internet much.
I only have tablet which I switched off having first checked the router to make sure there were no other wireless connections and adding MAC address filtering to be sure no one else was stealing my bandwidth. With just my router connected to the ISP, my ISP has recorded 170MB of downloaded data in 3.5 hours. Switching off the router stops the traffic being recorded (as you would expect), but when switched back on the large data transfers start up again.
I have plugged in an older router (not wireless) and no traffic is generated, so it seems to be the TP-Link router rather than my ISP or ADSL circuit that is at fault.
View 1 Replies
View Related
Mar 15, 2013
I've been looking around for a way to track my usage on my D-Link router. Any posts to address this seem to be a few years old. At that time, there was nothing I could do to track it via the 825. Any 3rd party firmware or anything from DLink that I can use?
View 5 Replies
View Related
Jul 24, 2011
I have a dell poweredge 830 (3.0 dual core pentium, 2gb ram, 2x160gb hdd in raid 1, dual port intel gigabit card). I'm trying to find a router OS that logs bandwidth by ips on the lan. I tried untangle and clearos neither of which have a feature (or one that I can find) that logs the bandwidth by ip. Apparently pfsense has a package you can install but I have never been able to get pfsense to work on this pc, it always errors in one way or another (on the 2.0rc3 I can't access the web page, it says it is missing a file).
View 19 Replies
View Related
Nov 7, 2012
Site-to-site tunnel between 881 router and ASA 5510 don't work stable,When PHASE 2 completed and Ipsec Tunnel has been builded, 881 resend some entities which will increment error counters.
View 1 Replies
View Related
Mar 22, 2011
I have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. URL We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
View 1 Replies
View Related
Dec 7, 2012
how to stress a GNS3 router in order view an increase in its CPU usage?
View 1 Replies
View Related
Sep 12, 2012
I have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. [URL] According to our baseline it should not be more than 40% at any given time. We see high CPU uptp 70% consistently.
CPU utilization for five seconds: 99%/0%; one minute: 57%; five minutes: 55%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
442 66173704 90234125 733 96.86% 46.09% 46.30% 0 BGP Router
7 509291060 26330202 19342 1.17% 3.90% 2.99% 0 Check heaps
Router has 1 eBGP session with ISP from where it downloads whole IPv4 internet routing table and two IBGP session with other two rotuer. When I look at BGP summary table I see many updates received from ISP and sent out to IBGP neighbors. Also did debug BGP updates to confirm it.
We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.
%BGP-6-BIGCHUNK: Big chunk pool request 628 for community. Replenishing with malloc
I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
View 5 Replies
View Related
Dec 13, 2012
I own a wireless router (ZTE W300) and due to the large number of devices in my house, and limited broadband usage, can I limit downloads/uploads (in other words, limit data usage) to a particular device over the network?I think the stock firmware on my router doesnt allow that (and its pretty base level too). If so, do you recommend any other firmware that can do the task, and is compatible with my router?
View 1 Replies
View Related
Apr 7, 2013
whenever I setup URL filtering in 1841 router with policy-map type http and zone-pair command, I experience 100% CPU spike. is there any workaround?
View 1 Replies
View Related
