I have a Linksys WRT160N connected and it is working fine. My problem is the coverage is not enough. I have a Netgear WRN2000 and I want to hardwire it to my linksys so it can be used as a repeater but I can't get it to work properly.
View 13 RepliesI'm currently writing this from a laptop. It can access the internet perfectly, with no dropouts and no speed issues. However, my desktop PC is a different story. When I purchased the PC, it came with a standard wireless PCI adapter which really wasn't doing the job. It couldn't pick up my router from just one story above, where my laptop could. I decided to buy a new wireless adapter that would hopefully fit the bill. Unfortunately, again it didn't pick up the router from downstairs. Trying a different tack, I purchased the Netgear WRN2000 as an access point that would increase the range of my router. I connected my PC to this after configuring and all was going well for a while, until now. Now, every 1-2 minutes, the internet will slow to a crawl for 30 seconds or so, and while comparing speeds via the laptop (connected directly to the main router) and via the PC (connected through the extender to the router), the laptop clearly has the speed advantage. This is more noticable when playing games on my PC, such as Call of Duty. Every 1 minute or so, the game becomes unplayable due to lag for around 30 seconds, and sometimes this happens constantly. I'm unable to work out if the WRN2000 has a problem, or if it's interference. I actually tried connecting my PC to my laptop via ethernet, and bridging the 2 connections, which seemed to work for a day or so, but now does not. Also, i'd be willing to purchase a new PCI wireless card if anyone has any recommendations for one that has a strong signal range.
View 10 Replies View RelatedMy brother has a router for his house which lives right next door. I am getting wireless through a adapter right now but not good throughout my house.
View 1 Replies View RelatedI was using my internet on my Acer Windows 7 operating system wireless just fine on Monday. I tried to use it on Tuesday and could not connect to the internet wireless any longer. I get an error message next to my network stating ""The settings [COLOR=green ! important][COLOR=green ! important]saved[/COLOR][/COLOR] on this computer do not match the requirements of the network"I have never encotured this kind of problem before. I proceeded to call Comcast who did all kinds of trivial beginner troubleshooting such as restart the router, restart the modem turn on and off the computer.
View 3 Replies View RelatedI have a netgear wrn2000v2 which I can't access using the default IP address 192.168.1.1. I can access it with routerlogin.com. What is going on?
View 1 Replies View RelatedI Have a 2 Access Points First One : TP-Link TL-WR542g V7 and this is a Picture of it: url...i Have my Router on The First floor and My Wireless Enabled on it With WEP Encryption.i Need To Extend The Coverage to The 2nd Floor,By Using one Of my 2 AP's.Setting up my AP To Receive the Wireless Signal From My Router And Re-send it To My Laptop.."Wireless"..So i can Leave it only With AC Power ..And Still Streaming The Signal While my Laptop Receiving.
View 1 Replies View Relatedbelkin n wireless router minimum coverage ?
View 1 Replies View RelatedI have to separate internet providers and two different modems (one brand new!) - they both appear to be working fine but I can't get any internet coverage - neither on my macbook air, Mac nor my HP netbook. All say ethernet cable unplugges. I have been on tech support with both providers all morning, and now with a tech guy in the house for the last 2 hours and all indications are that the modems work
View 1 Replies View RelatedMy router (D-LINK DIR-655) is in the living room under my TV in a cabinet with the lid closed (i would like to keep it that way, because the DIR-655 has the brightest led lights ever). My ground floor coverage is decent except in my back yard where i only get 1 bar or lose signal (we are talking about 10-15m distance). I am using mixed G & N mode with auto 20/40 MHz. In the past i had full bars in my back yard using a Linksys WRT54GL (Wireless-G) with DD-WRT firmware.
I have the following devices connected on my router: ISP MODEM / DREAMBOX / HTPC / DNS-325 / TV
1st Floor: I don't have any wireless coverage here, sometimes one bar but keeps dropping. This is where i would like to expand my wireless coverage in the whole floor.
2nd Floor: Here is my attic which i don't basically need any wireless. My main concern is in the 1st floor.
I have a decent sized wireless network (120 1142 access points on a 5500 WLC) and any tips for maximizing the coverage. I know the only REAL way to fill true holes is to deploy more hardware, but I'm not sure if my WLC is configured properly to maximize the hardware already deployed. We have having a lot of issues with low signal in areas I feel are close enough to the AP that they should be good if not excellent signals. Our initial walkthrough and testing of the areas indicated that the APs we deployed SHOULD have been more than enough, but in real-world conditions it seems like it's not cutting the mustard.
View 5 Replies View RelatedIn an idle situation how much area is covered by a cisco 3502i acceccpoint , I understand there are many factor that will effect this , thats why I am adking in idle situation , I am looking for a number is square feet.
View 1 Replies View RelatedIs this the best way to get maximum performance and coverage? I have a DIR-655 bridged to supply B/G on channel 11.I Gave Up On Linksys Firmware And Installed DD-WRT.
View 4 Replies View Relatedcould it the wireless ADSL modem + AP (e.g., WAG54G) coverage the wireless adapter.If answer is negative, then if both (wireless modem & wireless adapter), close to window, how?Again, if answer is negative, then may via Detachable Antenna of any devices that install out of window builds?
View 2 Replies View RelatedI had an old LINKSYS WRT54GS whihc had a poor coverage of my whole home.I just bought a new E-3200 which is supposed to have a real higher coverage but seems not.When I am in a room at 15m from the routeur, no coverage !How can we optimize the coverage of the routeur ?
View 5 Replies View RelatedI've been tasked with providing wireless coverage for an outdoor courtyard. The wireless that bleeds out into the courtyard is minimal for both 2.4 and 5 Ghz bands. I'm thinking a 3502p mounted just inside the wall hooked to a ANT25137NP-R patch antenna mount on an exterior wall. The red line on the wall will represent the antenna mounted on the wall. This will be providing coverage for phones on 5Ghz and general devices on 2.4.
View 5 Replies View RelatedI have been searching online for the maximum coverage (distance) of WAP4410N
View 1 Replies View RelatedWhat is the average/maximum distance coverable by Aironet 1300 and 1240AG ???
View 3 Replies View RelatedI have two 1130 AGs and would like to have one connected to a wired net with wireless clients on the G radio, and connected to the other using the A radio, and it having clients on it G radio.
View 1 Replies View Relatedcan't find SmartNet coverage for AP2602I
View 3 Replies View RelatedIn the bottom screenshot how to determine the coverage level, I couldn't find any explicit documentation on that .
View 3 Replies View RelatedWe did wireless coverage testing using some 1142 units in autonomous mode, and got a satisfactory result, but upon converting these test units to Lightweight and adding them to our WLC5508 controller, the coverage has decreased noticeably.
Any tips or tricks to getting lightweight 1142 APs to have a range as far as the same hardware with autonomous firmware?
expanding my WiFi coverage over a pretty large ares like 4 or 5 access points.
Heat-mapper Visualize Wireless Coverage Of Wi-Fi Networks?
View 2 Replies View Relatedi want to coverage area of Wi-Fi router of any brand
View 2 Replies View RelatedI have a Linksys wireless router in my basement and I want to extend coverage upstair. I have a office upstairs which has a ethernet cable that is plugged into my router in the basement, can I connect a Linksys Wireless G WAP54G access point to that ethernet cable and thus have a extender upstair?
View 1 Replies View RelatedMy DSL Modem connected right now to Linksys Model: WRT600N (Dual Band Wireless-N Gigabit Router) to give a wireless internet access in my house. I have TWO spare Linksys Wireless Router (WRT350N-Wireless-N Gigabit Router) and (WRT54G2-Wireless-G Broadband Router) that I need to use to expand my wireless network at home.
How can i connect the two routers to became an access point or range expander to existing router. It is possible the two spare routers became an access pt or expander? How can i configure that? Cable configuration?
I am facing this particular issue while providing Cisco unified Wireless solution to the customer. We are having CAPWAP 1252 APs controlled by WLC.
Scenario: 50 persons sitting in a hall with closely packed chairs using wireless simultaneously. Wireless access provided by patch antenna at a height of 11m from the user. As one AP can server 25 users, 2 APs are placed with antenna directions facing the compact users. Each users gets very good signal from these two APs.
Whether there will be serious interference and client association issues in this scenario? once one AP associates 25 clients, whether other 25 clients associate completely to other AP?
i have an Outdoor Area covered by Cisco Wireless LAN Solution (WCS,WLC,1550AP root and Mesh lightweight). I need to disable power transmission for some of these APs in the 2..4GHz.I tried two possible way, but both are not working:
1) Set the power of 802.11g/g/n to 0. There is no such option (power can be set manually from 1 to 5 and, as per the documentation, each level is a reduction of 3dB. Therefore, even if i put to the minimum, i cannot guarantee that there is no utilization of the 2.4GHz spectrum).
2) Define an AP group containing these APs and don't add any SSID. Is not possible because at least one SSID must be added on each AP group.
Working solution/setting in AP/WLC/WCS to avoid transmission in 2.4GHZ? Otherwise the only solution is to power them off?
I have an integrated 881W with a built in 801 access point. I'm interested in increasing the range of my AP. I'm interested in considering any configuration changes while still maintaining support for N. I've included a copy of my running config.As well, I've heard of high gain antennas. I'm using the default antennas that came with the 881W. If there are better antennas that I can buy to increase my range, I'm interested in considering that as well.
View 10 Replies View RelatedWhen a ap1121G joins WLC4404,it shows a normal heatmap in WCS. But when a ap1121G joins WLC5508,the RSSI in whole coverage is almost -35 dbm.I copy the heatmaps to the attached files.
The versions are as below.
WCS 6.0.196
WLC5508 6.0.200.29
WLC4404 5.2.157
Aironet 2600 and 3600 series. I need to know their maximum distance (at least theoretically, in Line of sight, eliminating all other factors...) in order to choose the right number of AP to provide enough coverage for a specific area. If an exact number is not available then can you show me how to determine it?
View 8 Replies View RelatedI want buy an Access point which cover 300 Meter coverage Area.
Have any data sheet or link where I can found which AP coverage how many Area, Like 1042 Access Point cover how many Feet Space.
I just upgraded my router from the WRT54GL to the EA6300, and it appears there is less coverage with the new unit. Previously, my neighbor could share my router and now with the EA6300 my phone switches to 4G at the end of the driveway. Has anyone seen any specs which publish to output of the ea6300?
View 3 Replies View Related