Router Configuration For Home Server
Oct 9, 2011
I'm trying to run a server for a java application called mekwars. The program needs ports 2347 and 4867 open. I have obtained an ip address from my ISP and registered with dyndns. I can ping my public ip address (my router)I can access my server from any other computer in the LAN. My router is a Zyxel p660hn-T1a. I have configured port forwarding of both ports to my server.I have disabled the firewall in the router and restarted it.My server is running CentOS 6. I have opened the ports in the server iptables, I don't think this is the issue as I can connect from my lan to the server.When I try to connect (from within my lan) to the public ip address of my server the program tells me it cannot find the server. I can't telnet to port 2347 and nmap tells me that the only ports that are open are 22, 23 and 80 ( I believe this are open by default on the router to allow remote management).I can telnet from the lan. My networking isn't great and I'm used to having an "ip passthrough" option on the router to assign to my server. I do have it set as the default router in port-forwarding so I had hoped this would be a similiar option.
Do I have to set a static route in addition to port forwarding or could I have port forwarding configured incorrectly? I'm also considering the router may be at fault and I've emailed my ISP to make sure they're not filtering the ports before they reach my router.
View 2 Replies
ADVERTISEMENT
Feb 11, 2011
in my past days i am using bsnl broadband. and also using adsl router for net-connection. i am connecting internet through wifi adsl router. now i am not using bsnl broadband. now i am using beem broadband in hyderabad. that internet connection is directly to my laptop through rj45 cable. but i want to configure adsl router to my beem broadband because i want to connect internet through wifi.it is possible or not? if possible tell me the procedure.
View 2 Replies
View Related
Jan 5, 2012
Here's my situation:I live in a house that has AT&T U-verse. My pc is a couple of rooms away from the U-verse router so I pick up my Internet signal via a Netgear WG111v2 USB wireless adapter. Works great. But I have a couple of "new" Palm Pre handhelds with sync software that requires a wireless connection (won't do USB). Fortunately, I had a Netgear WGR614 v4 54 Mbps Wireless Router in storage. (I used it years ago so it had already been configured but back then it was wired directly to an AT&T router with a patch cable to my roommate's pc and to my pc wirelessly.)
So I just powered it up, plugged a patch cable into my pc's NIC and plugged the other end into the WAN port. Voila! I had connectivity to my Palm Pre's. All was well for about 15 minutes when all of a sudden my pc lost connection (wirelessly) to the U-verse router. And though the Netgear Smart Wizard showed a strong signal from the Netgear WGR614 Wireless Router and the Palm's were picking up a strong signal from it, they couldn't "surf" the Net.
I guess WinXP (being PnP) decided to adjust things causing everything to stop working. (Just a guess.I moved the patch cable from the WAN port to a LAN port. This enabled me to access the Netgear router wizard for the first time since I used it years agohttp://192.168.0.1) I couldn't access it earlier in this "endeavor" when the patch cable was connected to the WAN port. So this seemed encouraging. But no, it didn't work. Nothing was connecting to the Net. And the only way to restore my pc's connection via the Netgear USB wireless adapter to U-verse was to unplug the Netgear wireless router.
View 1 Replies
View Related
Dec 20, 2012
I have setup a webserver on my home PC and I have forwarded port 80 on my router to the IP adress of the PC that is running the web server. The web server is working great; I can get to my web pages from outside of my home by going to http://MyIpAddress/Anyway, the problem is with the Windows Media Player plugin I'm using. I want to embed 6GB MPEG-2 videos into my web pages. I have some videos on my PC and I want to be able to watch them remotely by connecting into my web page. It works fine when I'm at home; other PCs can connect and play the videos no problem. The problem is when I'm at work. When I'm at work, I go to my web page (via my IP address in a web browser) and the Media Player plugin says "Connecting" for a minute, then it says Ready, but the video will not play. I tried using a smaller, AVI file (680 MB) instead to see if the problem was streaming such a large file, but the video still would not play.Do I need to foward more ports on my router so that Windows Media Player can connect back and get the information it needs?
View 4 Replies
View Related
Mar 12, 2010
configuration of 2 WRT160N's a RT31P2 and a EZXS55W to a home network. The reason behind this is a two story house and running more cat 5 lines for future use.
View 3 Replies
View Related
Aug 20, 2012
i live in a dorm and i want to stream movies to my nexus 7 but i dont want to buy a nas. can i connect my external to a router [URL] and use that to stream movies. i dont need to be able to connect to it all over campus (i know that involves hacking the proxy) but mainly in my room would be nice.
View 2 Replies
View Related
Feb 1, 2011
Any example of router config for a terminal server.In fact I need a configuration for a router with multiple, low speed, asynchronous ports that are connected to other serial devices, for example,modems or console ports on routers or switches.With this router I would like to use a reverse telnet to connect with my devices using the serial connection.I find many examples on the Cisco web site but none with my router hardware configuration.My router is a 3620 router with a 8 port async (NM-8A/S) network module and I would like to use the 8 serial interfaces, each of them connecting a serial device.
Here is the show run and show ver :Router#show ver Cisco Internet work Operating System Software IOS (tm) 3600 Software (C3620-I-M), Version 12.3(25), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Mon 28-Jan-08 20:16 by alnguyen
ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Router up time is 1 minute System returned to ROM by reload System image file is "flash:c3620-i-mz.123-25.bin"
[Code]...
View 1 Replies
View Related
Jan 12, 2012
I have a network that is currently set up in the following way:Modem -> vonage Motorola router -> wireless router Most computers are hard wired to the Motorola router. Some other ones connect via the linkseys wireless router. All computers are able to connect to the Internet. The problem I have is that I will be setting up a home computer as a file server connected to the Motorola router. The network acts as though it is two meaning that computers on one router can't see computers on the other router. What steps should I take in order to make all computers accessible through both routers.When I type 192.168.1.1 from a computer on the Motorola router, I get nothing, when I type in my actual ip address, I get the Motorola router. When I type in 192.168.1.1 from a linkseys connected computer, I get access to the linkseys router.
View 3 Replies
View Related
Mar 10, 2011
Is there an iTunes Server for WHS 2011 available?
View 3 Replies
View Related
Apr 18, 2013
I am looking at buying the EA6500 router. However, before I make the investment into buying this router, I need to know some basic information first.
1. I want to setup the EA6500 to accept FTP requests to my Windows Home Server. Yes or No?
2. Remote access to the EA6500, Yes or No? i am aware of the security risks
3. I need to setup Port forwarding on the EA6500. I assume I can?
4. Manage a Kindle Fire and other wireless devices?
View 5 Replies
View Related
Jan 14, 2013
I need to configure two VLANs in my home network to separate a server 1 with VM from another part of network with server 2 and wifi clients. Is it possible to keep DHCP server and internet access on E2500 enabled for both vlans? If so, how should I configure ports tagging (variant shown on screen shoot below doesn't work).
View 5 Replies
View Related
May 30, 2012
When I'm trying to access the Twonky setting page on http://192.168.1.1:9000/config I get: Access is restricted to MediaServer configuration! Is this normal or not?
View 2 Replies
View Related
Jul 6, 2011
how to get at the configuration interface for the "built-in" Twonky server on the E4200.Specifically, I'm trying to figure out how to get to the "clients.db" file and the area of the UI where I can configure the receiver settings. I'm getting the dreaded "unknown file format" message when streaming mp4 files to my Samsung BD-C6500 bluray player. Installing Twonky on my laptop and working with the problematic files has shown that the solution is a simple matter for BD-C6500 understand how the files are encoded.
View 9 Replies
View Related
Oct 23, 2011
I use to run Twonky media server on my iMac and I was very happy with it. Now I have purchased a Linksys Wifi Router E4200. Twonky server embedded works fine with all my devices except with my Samsung D8000 Led TV. In the Mac version I must identify manually the player (Samsung TV), if not mkv won't play. The question is: How can I select the device in the Linksys E4200? The config page is not available and displays "Access is restricted to mediaserver configuration" E4200 firm V. 1.0.03
View 9 Replies
View Related
Jul 2, 2011
I'm connected through a simple non-configurable switch to a 172.20.0.0. 255.255.0.0 network, with a gateway of 172.20.2.2.
When i use DHCP, i am able to connect to the web.
When i change my ip address to a static address (with an available ip address and correct subnet mask and default gateway) i am unable to connect to the web.
View 7 Replies
View Related
Feb 25, 2012
I have a router manufactured by AirTies,the model is Air 4450.This has the capability of being an Access Point in a current network, which is how I want to use it. (Introducing it into my current Sky Broadband network with a Sagem F@ST 2504N router).However, I cannot access the configuration page whatsoever.The manual states the default IP address of the router is 192.168.2.254, so I have set my laptop to a static IP of 192.168.2.100 and patched into LAN port #1 on the rear of the Airties 4450, powered on the unit and cannot access the router at all.I have held down the reset button several times to no avail.how I can configure this unit ?
View 2 Replies
View Related
Sep 4, 2012
I've been trying to configure a cisco ASA 5505 for my home network but I'm not having much joy with it. I've looked at countless guides, tutorials and followed the ASA setup wizard in ASDM. The Cisco 1841 is running sub-interfaces for my VLAN's.
View 4 Replies
View Related
Feb 10, 2013
I finally decided to get my own home lab so that I can configure to my hearts' content and not have to wait for access at the school to do it. I have three 2620 routers inter-connected with wic2t cards, and five 2950 switches. I have already set the config reg. on the routers to 0x2102 so that I can save my configs when I power down. When I pulled up the config regs on the switches, they all had 0xf as the reg number. Is this a good config reg number to have if I want to save the config before I power down?
Also, what would be a good ios version to have running on the switches and also the routers? I have access to other cisco IOS' but I want to double check. With this setup I would practice bgp, ppp, frame relay, rip2, ospf,eigrp, stp, pvst,pvst+, Rapid pvst+, rstp, and mstp.
View 1 Replies
View Related
Sep 22, 2011
I have an old Pentium 3 PC that I want to test out as a home server. I am thinking of using Linux server is but I don't have any ideas how to do it.
View 4 Replies
View Related
Sep 14, 2012
I have a 24-hour running computer that I want to make a small and simple server for personal useim: to put some photos on the server for my target audience from China. I have a 24 hour running computer located in my small flat in China. The purpose to make this is to provide a fast speed loading for average users in China? The links for the photo should be in format
View 4 Replies
View Related
Sep 4, 2012
I host a minecraft server for my friends, but I always have to give them my ip every time because my ip changes everyday, and that is really annoying.
View 11 Replies
View Related
Jun 15, 2012
I have a PC ready to use that I want to be used for sharing files, pictures and videos on between our multiple PCs in the house hold. I am going to have it constantly running (I have alot of cooling for it)
View 1 Replies
View Related
Mar 1, 2012
I got WAG200G and two computers, one connected by ethernet cable and laptop connected by wifi.How to configure router to get full speed of my internet connection on the desktop PC?Let's say i need 80% of my internet speed to download something on desktop, but in the same moment laptop also downloading something, how to setup router to get more downloading speed on the desktop.
View 1 Replies
View Related
Jan 18, 2011
I have a small home network. My goal is to use Windows Server 2003 R2 to setup a DNS Server that can create a few simple names for some devices on my LAN, such as my printer. My DNS server will forward other inquiries (like google.com) to OpenDNS. Additionally, I don't want to setup a domain controller for my network. I wish to continue using workgroups,how to setup a Windows DNS Server on a workgroup. My biggest confusion is the FQDN of my name server. By default, it's setup as "server.", where 'server' is the name of my Windows Server 2003 machine. My workgroup is named 'Home'. So I tried 'server.home', but this does not resolve. What DNS suffix do my other machines on the network use by default? Is my domain name on the network really my workgroup name? Another thing I want to avoid is configuring a DNS Suffix for every single client machine on my network in their NIC properties for IPv4. I have a D-Link router, and if I do an "ipconfig /all" on my machine, I see that my DNS suffix is 'router', which is the name of my D-Link router. I try setting my DNS Server FQDN as 'server.router' and that doesn't work either, so I'm out of ideas.
View 1 Replies
View Related
Apr 19, 2012
I'm running a Windows Home Server in my LAN and I would like to use it's functionalities (especially the streaming) features from "anywhere" using the same URL.My router is a Linksys WRT160Nv3 running.I've already setup the necessary port forwardings, as most of the WHS sites run on ports 80 (http) and/or 443 (https) and my isp is blocking all ports < 1024 (I know it suck, but nothing to do about)
View 3 Replies
View Related
Dec 11, 2012
I have an exhibition next saturday on network monitoring and I was given ftp server monitoring project. I'm only allowed to used linux based OS for this project. Right now I have 3 notebook. 1 as a client, 1 as a router and another 1 is for monitoring. Right now, I only can make a connection between the client and monitor notebook by using Freebsd in the router. How to setup a ftp server and how to monitor it?
View 6 Replies
View Related
Oct 13, 2012
I need idea for making my network simpler. It works currently great but i want to eliminate stuff. I have on my second floor a "server" with an wifi usb adapter (Alfa AWUS036H) for internet access which shares the connection, the server is connected to the WAG200G and he is then connected finally to my home pc. So if i want internet i have to run that router and the server constantly. As i said it works great but i would like to eliminate the server so i dont have to turn it always on, are there any possibilities? Here is a picture which shows it all!
View 2 Replies
View Related
Feb 11, 2011
How do you access an application that is in the server? Like what extra steps you gotta make? Are they software related or do I have to do some configuration on the router or switch? Heres a little example:
Assume you have a group of computer connecter to a switch, this switch is connected to a router which has the connection to your ISP. On the router, you also have connected a server farm for your network and all the apps are stored there, say MS Word, Excel and such.Now, you have your network running, every ping comes out successful, so you know you did that part right, so the next part is to get the host use the MS Word or any other app in that server. How do you do that? Is there something that need to be configured on router/switch or is it with a software on your host? If its a software, whats the name of it and how you make it work?
View 2 Replies
View Related
Jun 15, 2012
I have a PC ready to use that I want to be used for sharing files, pictures and videos on between our multiple PCs in the house hold. I am going to have it constantly running (I have alot of cooling for it) but I need setting it up.I dont know if I should use Ubuntu Server or FreeNAS?
View 1 Replies
View Related
Mar 26, 2011
I have a video hosting server on vmware and I need to be able to connect to it through it's domain name. It needs a FQDN. On it's network config it has spaces to enter in FQDN, IP, Subnet, and two DNS. It must use FQDN to connect through http.I was told I can just open up the system32/driver/etc/host file and edit in the info, ex: 1.1.1.2 [URL] I tried to ping 1.1.1.2 and it does ping, and I even tried to ping [URL] and it pings (not connected to the web). But I can't get the web interface to connect when i put in server.com:8080 (needs 8080) into my web browser. FYI, I have no idea about the DNS space on the server, I just put in some random number. Why does this server need a DNS anyways?This computer is not connected to the web or any other computer. It's just this computer and the vmware server on it.
View 4 Replies
View Related
Nov 21, 2011
I am just wondering how to set up a home network with an old computer used as a server... we will have a wii, ps3, lap top, and 2 desktops connected to the network as well as two dell printers. The laptop runs windows XP and the desktops run windows vista. The old computer will will use as a server is windows xp or windows 98 (most likely wont use that computer). What will i have to do to set this up and run the server as well as the network.
View 9 Replies
View Related
Feb 20, 2013
I am a networking student so have access to a free copy of Windows Server 2012. I want to setup and get experience with AD, DHCP, and DNS, among other services. Right now I have a Netgear router attached to a Cisco switch. (studying for CCENT cert) I have my desktop and server plugged into switch. I want my desktop to connect to the domain for testing and messing aroudn with. My wife has a netboook, smartphone, and wireless ipod. I'd like her 3 devices to get an IP from the DHCP server without having her authenticate to the server. Will the Netgear router allow this since wirless access is on? Or will she need to authenticate with the server to get a DHCP IP? I am gonig to disable the router's DHCP service.
View 3 Replies
View Related
May 22, 2012
I do not have wireless internet access and I get the message "There may be a problem with your Domain Name Server (DNS) configuration" when I try to diagnose the problem.I am on the internet by bypassing the router and having a wired connection from the modem to the computer right now. The problem started when I tried to get a second computer to work with the wireless connection (so with the computer I'm on right now, wireless worked a few days ago). [code]
View 9 Replies
View Related
