i have 2 ip's from my isp and 1 pc running on windows 7.i would like to switch the ip that is currently assigned to my pc to the other ip. is this possible?if so, what would i need to do?i am on a wireless network, through a dlink DI-624 router.
View 1 RepliesI have 2 PE routers connected to each other via 2960S and 3750 (non-metro) switches:
[PE1] -- [2960S] -- [3750] -- [2960S] -- [PE2]
I will be sending voice and data traffic between the two and my voice traffic will be marked DSCP EF & EXP 5.
Since the 2960's and 3750's can't match on the EXP bits, I am wondering if the "mls qos trust dscp" command still works. Is the 2960/3750 able to match on DSCP even though there's an MPLS header on top of the IP packet?
I'd like to avoid having to tag my VLAN traffic on the PE and rely on COS to achieve QoS in this case.
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View Relatedhow to connect two subnets with two switches and one router using router sim software?
View 1 Replies View RelatedIs it possible to daisy chain 3 switches and not have ip conflict? I am running a public access network for a library. For certain library software I need for all workstations to see each other. I have 25 workstations in total and two separate management consoles. I have all workstations on two switches but one of the management consoles is on the third switch because when joined with the others it has an ip conflict. I need this console for the digital sender that is connected as well as to act as a server for go print software.
View 3 Replies View Relatedhow to check and trouble shot broadcast issues on network
View 1 Replies View RelatedIf your wireless indicator is flashing red when you discover the smurf, it can mean that someone has tried to logon with an incorrect password. this is not necessarily an attack, it could be someone you have allowed access too, who has forgotten the password? In this case entering the correct password will solve the problem.However putting your own MAC address into the filter will simply block your own machine.
View 6 Replies View RelatedFor my work I am looking to create wireless capabilities to remote locations. To do this we are using a standard modem/router that is connected to an Engenius (802.11b/g) wireless outdoor radio connected to a dish antenna. We are able to go to locations (3+km) and then with a corresponding receiving antenna (using LoS), receive the Internet and connect both to computers at the transmitting point as well as to the WWW. The problem exists is that we want to employ a series of routers at the receiving end that would be able to carry the transmission to a different location (relatively close), due to the fact that some of the locations do not have line of sight to the antennas. We are using Encore routers, model # ENHWI-N3. When we connect the radio's Ethernet into the routers WAN reciever, we can connect to the Internet with a computer. The problem exists is we want to pass that connection over to a second router (R2). This connection is done when the routers are on access points set to a WDS function with R1 having R2's mac address and vice versa. Both routers are set to channel 1. Even when the routers are seperated by distances >50m a computer plugged into R2 can see a computer plugged into R1. Files can be transferred between the 2 computers wirelessly at speed around 3 mbps. However computer 2 on R2 can not connect to the WWW. This router features a spot that lights up if it has Internet access and R1's is lit up but R2's is not. How do we transfer the Internet and not just a LAN from R1 to R2 so it can be accessed further away from the point of the radio and antenna equipment. This setup has also been used where R2 is hardwired to R3. At R3 we change the channel to 11, and then connect through that with mac addresses wirelessly to 4th router. If comp is in R4 and far away it can still access and file share from comp at R1.*edit the ip address for the routers exist all on 192.168.1.xxx If the 3rd number is different between routers would this make a difference?
View 1 Replies View Relatedeverything was all good, my brother went crazy and unplugged everything.it effects our house phone too, that could be the problem.i just dont know what wires went where. all the wires are the same color.but i know which is which. just again, dont know where.i would like to get it done before he gets home later on.
View 1 Replies View RelatedThe first router is wired to the DSL modem and works just fine as an access point with Internet access. The second router is wired from the first router using one of the 4 ports on both router hubs. The second router is visible but has no Internet. How to configure the second router regarding DHCP, LAN, WAN, DNS etc.
View 3 Replies View RelatedWhat are procedures to deactivate di-604+di-704 routers+make the repeaters,connecting each of them,in a wired fashion,to my Belkin wireless N router?
View 1 Replies View Relatedhow to installs 3 router with same password
View 2 Replies View Relatedmodem
........ |
........ |
----switch-----
|................ |
|................ |
Router 1.... Router 2
|..................... |
|..................... |
Computer 1.....Computer 2
......................Computer 3 Router 1 points to a VPNRouter 2 access to the internetComputer 3 needs to access router 1 (VPN). Both Computer 2 and 3 are in a different room than computer 1, and router 1. Computer 2 is networked via cat5e to router 2.Is is possible to have Computer 2 and 3 share the cat5e, yet access different routers?
Can I connect 2 routers to one phone line so that I can receive a wireless internet connection throughout my house?
View 1 Replies View RelatedIf I have two stackable switches one switch uplinks to one 6509 core switch and the other connection uplinks to another 6509 core switch, and also the other stackable switch does not connect to the core switches. Because I am using hsrp and also we are not using vss then one uplink to the core is not in used only ones is so then how does creating an etherchannel between does two uplinks to both core switches benefit me in anyway such as more bandwith and using both uplinks at the same time or I'm I wrong?
View 7 Replies View RelatedIf I have two stackable switches were only one stackable switch has two uplinks one uplink goes to one core 6509 switch and the other uplink goes to the other 6509 core switch can a Layer 3 etherchannel be used if each uplink go to a different core switch, by the way hsrp is running between both switches and also can you give an example how data will be routed from the stackable switch through the ethernetchannel to one of the core switch accross the WAN to another core switch?
View 1 Replies View RelatedHow to set up a home network with 2 routers, where R1 acts as the DHCP server and R2 is basically a switch, connected LAN to LAN and everything is on the same subnet. Currently I have a different setup:Both routers have the DHCP server enabled and I connect R2's WAN port to R1 LAN. Therefore I have 2 subnets. Now my special requirement is that R2 is a DD-WRT router, which establishes a VPN connection to StrongVPN, so that all internet traffic via R2 is encrypted and goes through the StrongVPN server. Now my question:If I change my router setup to the same subnet, meaning R2 connects LAN to R1 LAN and I disable DHCP server on R2, will R2 still be able to establish the VPN connection?
View 5 Replies View Relatedi want to ask if i can link two routers while they are totally separated of each other over the internet to make a large LAN the two routers are TP link?
View 5 Replies View RelatedHow do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
I have one cisco 2851 router and one watchguare firewal currently being used as the main router. I want to connect the cisco as a secondary router on the same network.
View 10 Replies View Relatedhow to connect 2 routers on different lan
View 3 Replies View RelatedIn my office we have concrete walls and very limited wiring. The way it is set up is we have a Verizon DSL Modem that comes in then I have a router with it that splits the signal to 4 other routers that each split the signal 2 to 3 more times. I have to use routers so that it assigns IP addresses.I bought a new D-Line N300 Wireless router with USB imput. I want to attach my Home Media Network Hard Drive Cloud edition to the 1st router (attached to the modem) and then share the data off that hard drive with everyone connected to the sub routers.
View 4 Replies View RelatedI am trying to connect 2 wireless routers to expand my wireless signal. I want to connect the router 1 (in 2d floor) to a powerline av and then get the router 2 to the powerline (in the ground floor) so i can have wireless there too. I've tried some configurations i found online, but can't get to make the network functioning. The routers and powerline av are all dlink. I don't mind having 2 networks, but it would be better to have only one
View 4 Replies View RelatedI have a laptop connected to a net gear wireless router (for internet), but I am very close to buying a Belkin network USB hub to make my hard drive wireless, but this requires a router. I do not want move my hard drive to where my net gear router is, so I need to get another router, i am looking at a Belkin router so that I can make my hard drive wireless (This is the only reason for the router, it will not be used for internet) so I can keep my hard drive in the same place.
View 9 Replies View RelatedI would like to hook up 2 ip cameras to a server. I need to use 2 routers to do this. I already have the routers. router a is hooked up to the server. router b needs to connect wirelessly to router a. I can then hook up the ip cameras to router b. I just can seem to get it figured out.
View 9 Replies View RelatedI want to connect two routers wirelessly without running cables , any easiest way without cables.
View 1 Replies View RelatedI have a little probs@a site .we have a vsat link connected to a linksys E1000 router which is pluged into a cisco 2950 switch doing DHCP to the LAN,then a WAN link configured on a cisco 2911 router on static ip which is pluged into the same switch to serve the same LAN.I have been having issues of the workstations accessing both the WAN and internet@ the same time.
View 1 Replies View RelatedWe have a pair of N7K distribution switches connected to a pair of N7K Aggregation switches.We run vPC on both pairs of n7k's.
-n7k-d1 has two interfaces in a Port-Channel connecting to n7k-a1 & n7k-a2. (PC1)
-n7k-d2 also has two interfaces in a Port-Channel connecting to n7k-a1 & n7k-a2. (PC2)
My problem is that Spanning-Tree is blocking PC2 and all traffic from n7k-d2 is traversing the Peer-Link before reaching the Aggregation layer. Is this the best design for connecting two pairs of n7k's with vPC or if a better design would be to connect all 4 links into the same Port-Channel and vPC?
username and password i need to make a minecraft server but i need to get on the website.
View 3 Replies View RelatedI am planning to put an internet cafe in my place, i want to buy 20 units of PC to start the business. how to set-up or configure the PCs, How to use router and how to configure the PCs to activate the network.
View 4 Replies View Relatedhow can i make 3 computers connected wanly
View 2 Replies View RelatedI no longer have my netwk admin and i moved the server to my residence and i also have the pcs that logged on.i booted the servers up and connected the pcs using a router but can't log on im using a verizon wireless router can i get rid of that since i dont want to have it on the internet.
View 1 Replies View RelatedI have a working VPN with a WRVS4400N Wireless N VPN Router. There is a Windows XP computer on the network with a static IP address and a shared folder that I need to access with QuickBooks across the VPN.I can connect to the router; but only doing that is of little use. Once my VPN connection is made,how do I find the computer on the other side and map a drive to it or get it with QuickBooks? I need to do this with a Windows Vista Computer and a Windows XP computer at remote locations. Windows Vista seems to be different than XP in that it will not let me type a network address in Explorer without adding an HTTP://. Network places does not seem to work either.
View 11 Replies View Related