I downloaded the ISO for SSE 2010, and the damned thing is too big to burn to a DVD5. I doubt seriously MS expects people to have Dual-Layer discs handy.Is this intended not to be burned, but installed from the desktop instead? I can open the ISO just fine with WinZip.
View 5 RepliesI'm setting up a Network Monitoring System in Nagios and Nagvis. Now, I want to monitor the cpu and memory of the switches SGE2000 and SGE2010 with SNMP. Does the OID for the switches SGE2000 and SGE2010 (CPU and Memory).I can't not seem to find them on the Internet(searched for hours).
View 1 Replies View RelatedWe are using MS System Center Operations Manager to monitor network devices. We are trying to monitor our Cisco ASA 5525-X firewall interfaces.
We have a generic management pack installed that seems to work for parts of the 5525. We can see performance info for IF-4 but none of the other interfaces.
Our Management Pack is a generic Cisco Adaptive Security Appliance Version 9.1(1) management pack.
Is there a management pack that is specifically for this Cisco firewall?
My organization has about 15 workstations, all running XP Pro. Our server is running MS Server 2003.Is there a way to push Security Essentials definition updates to all these machines behind the scenes, rather than having each one download the updates individually?I would like to automate the process, if possible, so that once a week the update file is downloaded from MS update, then applied to all workstations, but I don't know where to begin.
View 6 Replies View RelatedI have purchased the ASA5512-K9 with the CX AVC and Web Security Essentials L-ASA5512-AW1Y as recommended by a Cisco pre-sales representative and my reseller for my environment. I had previously believed from the documentation on the Cisco site that all X generation models had the CX software included on them in the state that they are sold. Now in trying to configure the ASA5512, and with further reading of the setup documentation, I have discovered that I do not have the capability to access the CX functionality with this model 'as is', and this combination does not appear to be appropriate. It appears that the CX software module is not actually included on the ASA5512-K9 model, but rather only on the ASA5512-SSD120-K9 model.
If it is, should I exchange the ASA5512-K9 for an ASA5512-SSD120-K9 to get the combination of this subscription license and ASA model working. Am I correct in that the ASA5512-K9 model does not have a solid state drive on it already and so I can not download and install the CX software on it? As an alternative, is it possible to purchase a Cisco solid state drive seperately, plug it into the ASA5512-K9, download the CX software, and then install it on this new drive in the ASA5512-K9?
A make one BOM and i just ask my self can we order on the one platform ( for example 5510-SEC-BUN-K9 ) SSL Essentials license ( this license is on the platform by default we buy 250 users ) and i need 50 Users license from them to be Premium.
Can i buy those two license on the same platform and is this will work ?
I have a Cisco ASA 5500 Series appliance.I'd like to use the Embedded CA There’s no documentation which states an AnyConnect Essentials license will suffice, over an AnyConnect Premium.url... hints at Essentials being enough, as it specifically mentions some features require Premium, but I really need to be sure. Using AnyConnect Essentials (so, anyconnect essentials: Enabled) AND the Embedded CA?
View 1 Replies View RelatedWe upgraded and re-configured two existing ASA5520 platforms in order to provide an SSL VPN solution for one of our customers.
The customer opted to deploy AnyConnect Essentials the functionality / features they required for day one were catered for in the Essentials license and budget constraints meant Premium licensing could not be included in the original deployment.
The licenses added to the system were:
L-ASA-AC-E-5520= AnyConnect Essentials VPN License - ASA 5520 (750 Users)
ASA-AC-M-5520 AnyConnect Mobile - ASA 5520 (req. Essentials or Premium)
The customer is now seeing a growing number of mobile devices and wishes to support the BYOD culture growing within the business; as a result we now need to use features available in AnyConnect Premium. I am aware from reading the following document [URL] that AnyConnect Essentials and Premium licenses cannot co-exist on an ASA; I need to ensure we purchase the appropriate upgrade for the customer.
Is there an SKU to upgrade / migrate an existing Essentials deployment to Premium? I've reviewed the licensing guide and price list but cannot find a method which enables this transition.
Recently upgraded a 5510 to Anyconnect Essentials and Anyconnect Mobile, the device was Security Plus and is now Base. Is it supposed to work this way? I lost my Gigabit interfaces. Is it possible to have Security Plus + Anyconnect Essentials?
View 1 Replies View RelatedWe have instructed our user community to start their VPN sessions by connecting to our ASA 5520 with a browser to download (if necessary) and initiate the Anyconnect essentials VPN client. Everything was working fine until a few days ago.
We have had several people report the same problem. They connect with the browser, enter their login information and are greeted with our "authorized use only" message by the ASA. Then, instead of downloading (if necessary) and starting the VPN client software, the web page just goes back to the login prompt without displaying any error message. The client software is never downloaded or started.
We've been able to work around this by installing the client software manually (where necessary) and starting the VPN client from the start menu. However, this isn't our preferred solution because this method won't have them automatically picking up updated versions of the VPN client.
We have seen this behavior before when there was a pending Java update that had not been applied. However, that doesn't seem to be the case this time. Clients have recently updated to IE9, but I have personnally been running the Anyconnect client and launching through IE9 for months.
I have a RV 120W router and SBS 2011 Essentials server. The remote access was working porperly, but now when I type the URL it brings up the RV login screen instead of the Remote Access sign in page. I am not certain what settings are messed up.
View 3 Replies View RelatedI had my external drive plugged into the e3000 with the network drive mapped on 2 laptops. One day my connection was slow so I backdoored the router ip (I didn't use cisco connect) to reset the router from my iPhone. I'm not sure exactly what was changed, but the partition disappeared from the drive. I've used a couple file recovery programs to try and retrieve the 250+ Gb data that was on the drive with no luck. They only find "deleted" files. Not the 13k files that were there and not deleted. The drive was never bootable. What to be used to recover the files.
View 1 Replies View RelatedHow do I set my network key in Microsoft Word 2010
View 1 Replies View RelatedLost pin number for Microsoft 2010?
View 1 Replies View RelatedI have got a TMG 2010 and i want to use Skype through it. if HTTPS inspection is enabled skype doesn't work, if it is disabled skype is working.What can i do for using Skype behind a TMG with httsp inspection so i want to use 8080 port only.I have excluded the 1 PC from HTTPS inspection or the destination URLs from HTTPS inspection.
View 1 Replies View RelatedI think that our users are at the largest capacity for attachments, twice in the past week one of our users did not received important emails because of the attachment size limit. The problem is that the sender thinks we got it b/c there is no bounce back and we have no record of the email being sent. my question is how do i increase the attatchment size for incoming emails?
View 4 Replies View RelatedNo Network connection after Office 2010 install, I have limmited or no connectivity. I've removed and reloaded drivers, reset router, performed a netsh flush, tried to manually connect, kicked it, threw something at the wall and still no luck.
View 6 Replies View RelatedWe have acquired a cisco sge 2010 to replace our distribution switch. I set up the 802.1X network. Everything works great except I can not find how to enable 802.1x with 'Wake on LAN' on this kind of switch.
On catalyst I saw that it was sufficient to activate this control "authentication control-direction {both | in}" Except that it seems not to exist on this switch. Is there another way to enable 802.1x on WoL without using this command?
Or how to allow the magic packet (WoL) on a tagged port by unauthorized 802.1x?
I reinstalled my windows7 again, because my laptop was jamming so much. But i cant connect to internet via wireless. I dont have any other options to connect my computer to internet other than using wi fi. I think it says i didnt install the wifi driver. i tried something, but it didnt work. btw i have inspiron 15r bought in the end of 2010
View 16 Replies View RelatedI am working with a client to implement QoS for their Lync environment. Lync 2010 has this feature to mark dscp values based on packets tagged with logical ports. As an example, packets on port 49000 til 49999 will be marked to dscp 46(ef). On Cisco 2811 router, I am basically honouring the markings by the application and placing bandwidth priority on them and sending it out to the WAN.
The behaviour that I notice is that when port based packets are marked with a certain dscp value on the application, the router policy map doesn't pick up any packet increment for that dscp. But when all packets without port assigning to it are marked with certain dscp value, I can see increment on the router policy map for that dscp match. Why is this so???
The client wants the Lync to mark the packets with dscp value and the router is suppose to honour the marking, schedule the priority and send it out. [code]
i am working on a project with 2 security ASA's 5520 with Microsoft ISA/TMG-2010 Server having 2 DSL's my question is regarding the designing issue where should i connect the 2 DSL's using ISA/TMG-2010..
View 1 Replies View RelatedWe have a pair of ACE 4710 devices in front of a TMG 2010 array (3 members) and are having some issues. We have a nat pool on the ACE and need to be able to use integrated authentication in TMG since we are filtering URLs based on user ID. For example some users might have access to certain websites that other users do not have access to. TMG does all this fine when we send traffic directly to one of the TMG servers and it can successfully authenticate the user using the active directory username that was passed through. The problem occurs when we send traffic through the ACE first, upon which time the user credentials are no longer appearing to TMG and the user is getting prompted for a username/password whenever they try to access a website. Even when they do enter their username and password (which they shouldn't have to do) the request is still denied by TMG since it is coming from "anonymous" instead of their actual username.
Another problem we seem to be having which isn't as important right now is the fact that since we are using a nat pool on the ACE, every web request to the TMG servers comes from one of the NAT addresses, rather than the original client IP. Is there any way to get around this and have the actual client IP show up instead?
Currently i am having a scenario where i have setup RV042 and which is connected to Microsoft Forefront 2010. PPTP works fine only on rv042 subnet but i am not able to access the "internal" network of TMG.
RV042 (172.16.1.1) ---> TMG [external] (172.16.1.2) ---> TMG [internal] (192.168.1.1)
Is there any way through static route to access the TMG internal network through RV042 pptp server ?
I'm looking to do a basic QOS configuration which states that VOIP traffic has priority over anything else.
View 3 Replies View RelatedWe have the following setup on our Cisco ASA version 8.6.1 One to one NAT rule from outside to our Exchange 2010 cluster IP address (DAG group). This is working fine for clients on the internet accessing their emails via Exchange using their phones. The ASA has the MAC address of the active node from the cluster but when the cluster failover it cache the IP address and are not updating the new MAC when the cluster failover. So users from the outside are unable to connect to the new node from outside the ASA as the MAC address from the passive node is in the MAC table. The MAC address on all the switches update within 2 seconds on the internal network and users don't notice any outage.
View 4 Replies View RelatedIm testing ASA 9.0, that according to the release notes should support SharePoint 2010.But I still get the same problems I had with previous versions: the ribbon does not show up (just a loading spinner) and javascript popups do not show as well.
View 3 Replies View RelatedI lost my network connection after installing Microsoft office 2010.. what can I do to get it back ? I know it is this as i have been fussing with my computer all day.. I created a system restore point just before I installed it.. had network connection.. installed office 2010 and now once I rebooted I dont.. I am running Win 7 enterprise.
View 8 Replies View RelatedI have a toshiba 2010 windows 7 laptop, and like two days ago it wouldnt connect to my wifi. i keep going to network and sharing but my network wont come up everyone elses does though. ive tried to fix problem but it just keeps saying connect to a network..or plug in ethernet.
View 1 Replies View RelatedI want to work on quickbooks 2010 pro between my desktop which is windows vista and my lap top windows 7. I will be the only user, how do i set this up?
View 3 Replies View Relatedif the sge2010 switch support Routing Information Protocol (RIP) and if so how do I enable it. I have a small wireless router that support it and would like client connected on it te bo visible from the wan side and that worked when I had another device doing the routing with RIP support the wireless router was picking up that information and the routing for the wireless client was working.
View 2 Replies View RelatedI am trying to port forwarding Exchange 2010 OWA using ASA5505, wherever I used object NAT or Twice NAT it just doesn't work.... here is my config:
access-list outside-access remark "Exchange Server Access Rules"
access-list outside-access extended permit tcp any host <public x.x.x.11> eq smtp
access-list outside-access extended permit tcp any host <public x.x.x.11> eq https
[code]...
note that i use public ip <public x.x.x.9> on the outside interface for PAT, so all hosts in the same private can access internet
We have a 5520 ASA running 8.4(2). We are trying to setup Clientless VPN access to our SharePoint 2010 environment. We have most of it working, however there are a few things that do not function right in SharePoint via the VPN but function fine internally. Are there any special things to configure specific to SharePoint? Some of the things that do not work include the SharePoint ribbon, up level function, opening of documents within SharePoint, etc.
View 3 Replies View RelatedLately I've noticed some strange behavior on some of the switch ports. When I go through the logs my SGE2000/2010 stack, I see that some of the ports randomly lose their connection:
2147482703 05-Jan-2013 04:11:43 Warning %LINK-W-Down: 2/g14 2147482704 05-Jan-2013 03:35:20 Warning %STP-W-PORTSTATUS: 2/g33: STP status Forwarding 2147482705 05-Jan-2013 03:34:50 Informational %LINK-I-Up: 2/g33 2147482706 05-Jan-2013 03:34:47 Warning %LINK-W-Down: 2/g33 2147482707 05-Jan-2013 03:34:19 Informational %LINK-I-Up: 2/g33 2147482708 05-Jan-2013 03:34:17 Warning %LINK-W-Down: 2/g33 2147482709 05-Jan-2013 03:34:15 Informational %LINK-I-Up: 2/g33 2147482710 05-Jan-2013 03:34:14 Warning
[code]....
I'm having trouble locating the source of the problem. The devices connected to the port are servers and desktops. This happens frequently throughout the day, but not always on the same ports. What could cause the random drops?