Thomson TGW850-4 Router - Splitting The Connection In Two?
Feb 4, 2012
I have cable internet with 12 Mbit download and 1.25 Mbit upload speed. I'm using Thomson TGW850-4 router and I'm sharing the connection with my brother. Each of us have our own PC, of course.
Problem is, my brother downloads torrents while I play online games which completely screws up with my ping (from 40-80 to 350+) which makes them pretty much unplayable.
Is there a way to split the connection in two so that each of us gets 6 Mbit download and 0.625 Mbit upload at all times so that his torrents don't interfere with my online games?
I have 128KB Dsl connection and two Computer i need to splite them equal. i mean 64KB for each computer, it's very annoying when another computer start downloading or something like that then my computer is totally down.
I've noticed recently that my laptop keeps disconnecting from the internet via my router (Thompson Speedtouch ST585v6sl.)The light on the router that shows the connection turns red or sometimes it doesnt light up. However all the other lights stay on, it's just the internet light.It only happens for around 5-10 minutes and then after troubleshooting, disconnecting and reconnecting it's back up.I've scanned my computer for viruses and malware and nothing has come up, this is happening reguarly now about every 30-45 minutes when i'm on my pc.
Trying to split a supplied fixed IP address to multiple wireless devices so that I can piggy back on the internet connection in my office. Cause the IT dept refuse to provide a router.I plank to use a router for the job above.
I was wondering if the EA3500 would support splitting the USB (buying a USB tree) to allow for both a printer and hard drive to connect at the same time?
I have a problem with my thomson tg585 v7 router wich is that I can't gain access to it, each time I enter the default username and password (admin ; admin) it automaticly brings me back to the previous page.
A Thomson TG585 v7 (Modem + WiFi Router) receiving a DSL connection and Providing internet access on two interfaces connection : 1- WiFi : to connect portable devices at my home. 2- 4 Ethernet ports : to connect my desktops. One of these ports on my Thomson is connected to a D-link unmanaged switch to provide extended wired connections. From this unmanaged 4 ports switch one port is connected to my neighbors in another building through UTP, and connected to a D-link DIR 605-L WiFi router, the IP address of the DIR 605-L is 192.168.1.77 and the IP address of my local Thomson is 192.168.1.254 which means they are in the same network. I need to access the DIR 605-L WiFi router from my my home where I am connected directly to Thomson router through UTP cable, I am not able to do that !! , while also I can't even ping the DIR 605-L IP 192.168.1.77.
i have configured my wireless router.But im having problems. I can connect to the the internet using a lan cable which is connected to the router. but when im using the wireless connection i do not have internet connectivity.
Our ISP provided a Thomson dwg855 at installation of our service.We need greater coverage.Is is possible to use the output port on the modem to connect to a wireless router or other wired device?
I currently have a Thomson speedtouch router that i have yet to connect to my pc as i am waiting for the adaptor for it.I use AOL adsl line aol have goiven me instructions to connect the router to my PS3 either wireless or ethernet cable.I go through all the instructins but when i finally check connection it finds ip address but the internet connection has failed ie timed out 80028E02?
I have a "Thomson TG585 v7" router I reset it and the default username is "user" and password is "admin". So after the restart I want to configure again the router so I click the "Set Up" option I click "Next" and then show me to enter again the username and password but they are not the same as the router username and password. What can I do?
I have a thomson speedtouch ST585 router hooked up to my DSL line. I am trying to replace the wifi AP of the thomson with my linksys router (running dd-wrt). So far I have connected the linksys router (from the internet port) to the thomson router, and turned the thomson's wifi off. But, now I can't connect to the internet though the linksys router...I have tried disabling DHCP with no success?
Update:I can now connect to the internet through the linksys router, the problem now is that I cannot access the linksys's routers setup page. I can access the speedtouch's though.[URL] I would like to be able to manage all the forwarding (and the ip's) though the linksys router NOT the thomson (I want to make the linksys router the core router). I just need the thomson for my DSL line, I don't want it to do anything else but provide internet to the linksys router.
AOL are a complete waste of time and space in my opinion as for one you cannot understand what there tech support is saying and even when you email there tech support they seem to answer with a totally different answer to my questions.I have just installed a pci card ethernet connection on my pc windows xp now all I want to now do is connect and configure my router on the internet, I currently use aol dial.bb broadband adsl connection so far there are no connections from the router connected to my pc as i am still using a bt voyager 105 modem.When i did connect the ethernet cable to my pc and into the router also i connected the adsl cable into the back of the router but aol have not explained how to connect to the internet to configure this router and get it to work.
I have a Thomson tg782, with a USB port on the side. I want to plug my sub modem internet into that usb port, and then share that connection over wifi, because the router has a wifi function.
I have an issue with my home network that is really stressing me out now. I have a Thomson TG585 v8 router that my laptop, iPad and iPhone connect to no problem but my iPad/iPhone won't talk to my laptop.. I want to be able to use my iPad to remote in to my laptop to watch movies etc. Network sharing is on the laptop and I've checked that all devices are on the same network..I can't ping the iPad or iPhone from the laptop either.
I used to have a Thomson st-330 USB modem for my ADSL network. When I wanted to change my IP i just disconnected and reconnected a dial up connection that does the job instantly! (a wan miniport + a batch file to disconnect/recoannect with my password and username)Few days ago i bought a new modem/router (TP-LINK TS-W8951NS)Before that all I knew was that if I wanna change the ip address (if I have a router) was a batch file with commands ipconfig /release/renew.I now know that this changes the ip of my PC not the global IP! So how would I change it without restarting the router? (When i change something in my router interface page (PVC1.2.3....etc) my IP changed instantlybut how do I do this without accessing the router, like commands and a batch file etc? I just found out that my global IP changed on its own after like 30-60 min :S why is that! and to do so manually???
I have a Thomson TG784 router and i have a problem with it. once i turn on my rouet, and no cables are plugged in, except the power one, the two lights start blinking. The Power and the Ethernet ligh blinking. Once i connect my Ethernet cable and my DSL cable, the light are still blinking with no changes... What should i do?
I'm trying to setup a Canyon CN-FW514 wireless router through a Thomson modem.When I first started trying, I could get up the set-up screen on [URL] however this is as far as I got; the laptop said it had a very strong signal with the wireless connection, but I could not get any web pages to open (windows explorer couldn't detect any problems either). The Thomson modem works when I conect it to the laptop via the ethernet cable, but that's not much use to me trying to use the internet elsewhere in the house!I tried changing the IP address, subnet mask and gateway IP address on the set-up screen [URL] which seems to have been a big mistake; I now can't even get the set-up screen to appear.I've reset the internet options and have set everything to obtain the IP address automatically but am still having no luck.
Five months ago we moved into a new apartment, and connected up our broadband; the ISP provides a Thomson Speedtouch modem (ST546 v6), which I understand from Tech Support is running software v4 (it was issued with V5, but rolled back to V4 for stability issues).We prefer a WiFi network, so purchased a Belkin N Wireless Modem Router (F5D8636-4 v2); I connected it up ditching the ISP issued modem, and all worked well for four months. Suddenly it refused to see the ADSL connection - orange light flashing.So after four nights of 'fault resolution' with Belkin, they decided to send me a replacement... which I finally received last night. It didn't work - same problem, flashing orange light.I have the correct user name and password for the ISP - checked it not once, not twice, but four times. The Thomson Speedtouch works, but doesn't provide a WiFi environment. Can I connect the Belkin modem router into the back of the Thomson and transmitt/carry the WiFi signal that way, and if so, how? I tried (the obvious to me) plug a ethernet cable from the Thomson modem into the Belkin, but nothing.. I'm guessing there are a few important steps I missed.
I'm trying to create a VPN through a Cisco 861 but the problem is that the ISP forces me to use a SpeedTouch gateway ( as they use the MAC address for the authentication).By now, i'm getting OK pinging from client to 192.168.254.1, but I can't reach Internet.If I connect the client directly to the Speedtouch internet works properly. [code]
I have Mediacom cable and internet and I was trying to hook both up in the same room.When I connect it directly from the internet cord to my modem it works fine.But when I connect it using a splitter to hook it up to my modem and tv, only the tv works.So, how would I get this to work??
I have a little weird request at work. One of our offices would like to split the VOIP traffic. At that office we have a 10MB primary and 3MB backup circuit. Currently the phones are routing over the 10MB circuit. The General Manager would like to use the 3MB backup circuit for VOIP traffic. For the 3MB we have two T1 lines bundled together in a multilink. Configuration is bellow if needed
I'm trying to connect a second desktop to my internet connection. My current setup has my primary desktop using a wireless card and getting internet from the wireless router. Then I bridged the connection from my desktop to my xbox. Everything worked perfectly.
However, I recently got a second desktop(running lubuntu if it matters) and I'm trying to get it connected so that I can use Synergy and share a mouse with it. I found an old router laying around the house and was hoping I could use it to share the bridged connection to my xbox with the second desktop. Like this:
I couldn't get that to work though. The second desktop knew it was connected, but it couldn't connect to the internet. It would also throw off my primary desktop and it would try to connect to the old router.
I also tried to set it up like this:
Using an ethernet plug in the wall that normally just went to the TV and trying to split it there. The TV still worked, but the second desktop didn't.
How I can get this all working. I'd like to do it without having to order a wireless card/usb and just use what I have.
So I used to use a Thomson TG585v7 modem router (wireless) as my means of connecting to the internet, the aerial cracked on it and I began getting dropped connections, so I went out and bought a D-Link DSL-2730B modem+router. I am hooked up wirelessly to the internet as there is no phone jack in my bedroom, and I experience massive and prolonged lag while playing call of duty 4 multiplayer, which I never had before with my old Thomson modem. My ping also shoots up to about 400 and then 999 while I teleport around the map.
In one of our offices in Tokyo, we used to connect to the internet using a PPPoE connection from an ASA5505 and then ran multiple IP SEC tunnels to our remote sites. We have a /28 public range, but I couldn't work out how to utilize the other addresses, as the firewall was assigned a /32 on it's dialer.
To try to use more of the address space, we changed the topology and put a 1921 router at the internet perimeter terminating the PPPoE and then connected the inside of that to the outside of our ASA5505. We split the /28 into two /29 sub nets. the dialer interface of the router has a /32 from one of the /29s and the link between the inside of the router and the outside of the firewall used the other /29.
Since that change, we have had a number of performance problems to devices located behind the firewall (over VPN). If there's no traffic going over it, then response times to the public facing interfaces of the eqpt there are good. The more traffic we push over it the more packet loss we get. The response times are consistent, it's the packet loss that's the problem. There are no errors or drops on the PPPoE interface.The obvious answer to this is that we're pushing more traffic over it than we should, but it's a 100Mb circuit and I'm having severe packet loss if I try to push about 2 or 3 Mbps through it.
We're pretty certain that it's an ISP problem and can't say for sure that the problem started when we changed the topology out there, but anything to do with the way we've split the subnets out like that?
I have a pair of ASA5510 currently running as a failover pair. For some reason we need to move one of the firewall to another site, is there any best practice on splitting up the failover pair then I can re-configure the secondary unit offline?
I'm thinking to power down the secondary unit, unplug it from the network totally then erase the configuration on the secondary unit on console so I can re-configure it. For the primary unit, I will disable the faiolver config by "no failover" on the primary unit. Is that necessarily all thing for splitting up the failover cluster?
I would like to connect to a 1Gb routed uplink, and then impose bandwidth limits (via shaping/policing/whatever) on a per port basis. The ports could either be configured to route, or as switchports on separate VLANS. I'm trying to identify hardware that will let me do this. The set up I have in mind is shown below.
I am wondering if the IP Services Adv software on that switch will allow that functionality?
how to go about config my bureau connected to HQ and separated by a WAN link of 60mb.
This is my plansplit into halves that is 30 mb for LAN connections, internet and file serving for strictly video streaming, bureaus have routers 2800 conected to HQ HQ has a router 3900
I have a desktop with a "black screen", but the computer is running. I need to get files/documents off that computer. How can I get them without being able to see the monitor? I have a netbook, a portable hard drive, and regular ethernet cables, but not a cross over cable.
Now I have a 172.16.0.0/16 network with a def. gw. for internet where is a MS Forefront TMG 2010 with BSplitter for traffic shaping. I purchased an 2921, 2,5 GB RAM, security+data license and an EHWIC-D-8ESG.
I made 4 subnets in a test environment with some access-lists, nothing fancy yet. How can I use FF TMG for bandwidth management, where should I put it? For those 4 subnets the def. gw. is, normally, the 2921 router. TMG is splitting traffic by client IP.
The problem i'm having is that i'm using a 100gb capped internet plan, but after 1-2 weeks it gets all used up. After checking to see who's accessing the internet there's 2 unknown mac addresses who are constantly accessing the internet. Whenever this happens, the internet becomes considerably slower (i'm guessing they're torrenting or downloading off our internet).
I've even tried changing the wpa password but they're somehow still accessing the internet. So i've been looking for a way to ban mac adresses but i can't seem to find the option on the router.
Here's a screenshot:
YES, i know there's an option that says "Allowed on WLAN", but i cannot un-check the box for some stupid reason.
I really don't know what to do! Is there some kind of command i can type in the command prompt or something to ban mac address manually?
