I have 128KB Dsl connection and two Computer i need to splite them equal. i mean 64KB for each computer, it's very annoying when another computer start downloading or something like that then my computer is totally down.
View 4 RepliesI have cable internet with 12 Mbit download and 1.25 Mbit upload speed. I'm using Thomson TGW850-4 router and I'm sharing the connection with my brother. Each of us have our own PC, of course.
Problem is, my brother downloads torrents while I play online games which completely screws up with my ping (from 40-80 to 350+) which makes them pretty much unplayable.
Is there a way to split the connection in two so that each of us gets 6 Mbit download and 0.625 Mbit upload at all times so that his torrents don't interfere with my online games?
WRT54GL has an option to restrict or share the bandwidth equally to each ethernet port or wireless? I need this option in a low bandwith area because the first computer connected to the router who makes some traffic (e.g. youtube) takes all the bandwith allocated by the ISP. url...
View 1 Replies View RelatedI have Mediacom cable and internet and I was trying to hook both up in the same room.When I connect it directly from the internet cord to my modem it works fine.But when I connect it using a splitter to hook it up to my modem and tv, only the tv works.So, how would I get this to work??
View 1 Replies View RelatedI have a little weird request at work. One of our offices would like to split the VOIP traffic. At that office we have a 10MB primary and 3MB backup circuit. Currently the phones are routing over the 10MB circuit. The General Manager would like to use the 3MB backup circuit for VOIP traffic. For the 3MB we have two T1 lines bundled together in a multilink. Configuration is bellow if needed
3MB Circuit
I'm trying to connect a second desktop to my internet connection. My current setup has my primary desktop using a wireless card and getting internet from the wireless router. Then I bridged the connection from my desktop to my xbox. Everything worked perfectly.
However, I recently got a second desktop(running lubuntu if it matters) and I'm trying to get it connected so that I can use Synergy and share a mouse with it. I found an old router laying around the house and was hoping I could use it to share the bridged connection to my xbox with the second desktop. Like this:
I couldn't get that to work though. The second desktop knew it was connected, but it couldn't connect to the internet. It would also throw off my primary desktop and it would try to connect to the old router.
I also tried to set it up like this:
Using an ethernet plug in the wall that normally just went to the TV and trying to split it there. The TV still worked, but the second desktop didn't.
How I can get this all working. I'd like to do it without having to order a wireless card/usb and just use what I have.
Trying to split a supplied fixed IP address to multiple wireless devices so that I can piggy back on the internet connection in my office. Cause the IT dept refuse to provide a router.I plank to use a router for the job above.
View 4 Replies View RelatedIn one of our offices in Tokyo, we used to connect to the internet using a PPPoE connection from an ASA5505 and then ran multiple IP SEC tunnels to our remote sites. We have a /28 public range, but I couldn't work out how to utilize the other addresses, as the firewall was assigned a /32 on it's dialer.
To try to use more of the address space, we changed the topology and put a 1921 router at the internet perimeter terminating the PPPoE and then connected the inside of that to the outside of our ASA5505. We split the /28 into two /29 sub nets. the dialer interface of the router has a /32 from one of the /29s and the link between the inside of the router and the outside of the firewall used the other /29.
Since that change, we have had a number of performance problems to devices located behind the firewall (over VPN). If there's no traffic going over it, then response times to the public facing interfaces of the eqpt there are good. The more traffic we push over it the more packet loss we get. The response times are consistent, it's the packet loss that's the problem. There are no errors or drops on the PPPoE interface.The obvious answer to this is that we're pushing more traffic over it than we should, but it's a 100Mb circuit and I'm having severe packet loss if I try to push about 2 or 3 Mbps through it.
We're pretty certain that it's an ISP problem and can't say for sure that the problem started when we changed the topology out there, but anything to do with the way we've split the subnets out like that?
I have a pair of ASA5510 currently running as a failover pair. For some reason we need to move one of the firewall to another site, is there any best practice on splitting up the failover pair then I can re-configure the secondary unit offline?
I'm thinking to power down the secondary unit, unplug it from the network totally then erase the configuration on the secondary unit on console so I can re-configure it. For the primary unit, I will disable the faiolver config by "no failover" on the primary unit. Is that necessarily all thing for splitting up the failover cluster?
Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB(code)
I would like to connect to a 1Gb routed uplink, and then impose bandwidth limits (via shaping/policing/whatever) on a per port basis. The ports could either be configured to route, or as switchports on separate VLANS. I'm trying to identify hardware that will let me do this. The set up I have in mind is shown below.
I am wondering if the IP Services Adv software on that switch will allow that functionality?
how to go about config my bureau connected to HQ and separated by a WAN link of 60mb.
This is my plansplit into halves that is 30 mb for LAN connections, internet and file serving for strictly video streaming, bureaus have routers 2800 conected to HQ HQ has a router 3900
I have a desktop with a "black screen", but the computer is running. I need to get files/documents off that computer. How can I get them without being able to see the monitor? I have a netbook, a portable hard drive, and regular ethernet cables, but not a cross over cable.
View 1 Replies View RelatedNow I have a 172.16.0.0/16 network with a def. gw. for internet where is a MS Forefront TMG 2010 with BSplitter for traffic shaping. I purchased an 2921, 2,5 GB RAM, security+data license and an EHWIC-D-8ESG.
I made 4 subnets in a test environment with some access-lists, nothing fancy yet. How can I use FF TMG for bandwidth management, where should I put it? For those 4 subnets the def. gw. is, normally, the 2921 router. TMG is splitting traffic by client IP.
I was wondering if the EA3500 would support splitting the USB (buying a USB tree) to allow for both a printer and hard drive to connect at the same time?
View 1 Replies View RelatedI have an Acer 7750G, running Windows 7,connected to our home network using a Dynex router. At the moment this is the only laptop in the house that is having problems with connectivity. Starting yesterday, it only connects intermittently. When I run diagnostics, it says the following problems have been fixed but it either solves the problem for a few minutes only or not at all: "Problem with wireless adapter or access point" or "Default gateway is not available".
IPV6 connectivity also shows 'no internet access' and sometimes IPV4 reports no internet. I've unplugged and rebooted the modem and router a few times but that hasn't solved the problem.
Edit: I ran troubleshoot again, and it says the following issue is not fixed: "Wireless Network Connection 2 does not have a valid IP configuration".
I have a Cisco 3725 running IOS 12.3. I have three WAN connections (2 x 100Mb and 1 x 2Mb serial) and I need to replace the 2Mb serial connection with a further 100Mb connection. However, I have not got any spare 100Mb sockets.My plan is to use a switch that supports VLANs, connect the three WAN connections to the switch, each in their own VLAN, then connect the switch to one port on the router, configuring the switch port as a trunk (so that it passes all three VLANs across the link) and configuring the router so that for that single Ethernet interface, it has three subinterfaces each configured for a VLAN that matches the VLAN used for the corresponding WAN connection.
I am a bit rusty on my IOS so I wanted to run this all past the community for feedback. [code] Any thoughts on whether or not that will work? Are there any commands from the original interface configurations that I CANNOT use when moving them to a subinterface? I'm thinking that the speed & duplex commands need to be removed?
We're getting "Connaction Timeout / Connection Failure" error messages several time per day. Here is our setup:
Verizon FiOS Internet (ONT Box) --> Cisco ASA 5505 --> EdgeMarc 4500 Router --> Cisco 300-24G Switch --> Dell PE1950 Servers
From past few months, we keep getting Connection Timeout and Connection Failure error messages in our vendor application which connects to SQL Server 2005. Also Terminal Server 2003 keep disconnecting for every few hours.After several days of troubleshooting, we come to know that this Cisco ASA 5500 is not working properly. When I access the ASDM, it shows several warning messages.I know there is a setting option to configure TimeOut, but is there anyway to test and track the ASA 5500 regarding this Timeout issues?
I have a problem with my computer connections.When I plug in a network cable to access LAN, a wireless Internet connection gets disconnected.When I unplug the cable internet connection through wireless comes up.Some computers can support both connections cable for LAN and wireless for Internet.Other computers do not support both connections.
View 7 Replies View RelatedI just bought a "DLink Xtreme N Gigabit Router DIR-655" I configured it correctly. It works well for the wireless connection but my Lan connection (wired connection) does not work. The Lan computer connects to the router but cannot access the internet. All of my machines work OK with a Netgear G router, including the Lan computer.
View 9 Replies View RelatedI am trying to confgure a VPN connection on a Cisco ASA 5505, and I am supposed to translate the inside network from 10.200 76.0 to host 10.1.4.204, and then from that scheme establish a VPN with the host 66.179.80.108 on network 192.168.50.0/24. I was told that this Cisco ASA appliace would be able to translate the network address as a mask in order to make the necessary connection with the other site connection.
View 6 Replies View RelatedI have problem with my Internet connection. Recently my Internet connection often get slow. There are 3 connections on the server running Windows Server 2003. 1st is External, 2nd is Internal and 3rd is VPN (please see attahement). There is nothing to do with External and Internal connections, and everytime the Internet connection get slow, I have to disconnection VPN (connection) and connect it again.
View 5 Replies View RelatedAfter connecting to the internet on my laptop, the internet connection will work great for 10 minutes or less than it slows down drastically or essentially not working at all. If I disconnect and reconnect it will work again but just for a short amount of time. The wireless connection works great on iPod, IPhone, and tablet. Downloaded Kaspersky Antivirus which said it fixed some viruses but internet got worse after that. Tried restoring the computer to factory settings and the internet stays connected for what seem a few minutes longer.
View 3 Replies View RelatedEvery time I boot up my computer, everything will be working fine for about 5 -10 minutes, but after this, all my browsers will lose connection to the Internet. All of them: IE, firefox, chrome, even the steam browser, all of them just lose connection.The weird thing is, my net connection is perfectly fine: I can still play online games, still use online chat services, still open and use programs like utorrent. It's like something is just blocking all my browser connections.When I run a network troubleshooter, it says "your computer appears to be correctly configured, but the device or resource (Microsoft Corporation: Software, Smartphones, Online, Games, Cloud Computing, IT Business Technology, Downloads) is not responding."I googled this and came across some apparent fixes like flushing and re-registering my dns and restarting my modem, niether of which has worked.In addition, this problem is showing up on two totally separate shared networks and has only affected my computer. Other netwworked devices, like friends/families computers and my iPhone (which I am using to type this) work fine.
View 1 Replies View RelatedMy hp laptop will no longer connect to the internet thru both a wifi connection or cable connection. I've also tried to do a system restore to an earlier date and it will not let mme do this either
View 4 Replies View Relatedso I would like to know if I have a cisco 800 series lets say with interface fa0/0 being my public interface.can I have on this interface an easyvpn connection to a hub and a crypto map xyz connection to another hub?all the tests I've done using gns3 indicate no. when I have both on the same interface only eazyvpn works. when I remove the eazyvpn from the interface then site to site works.I know with a crypto map I can have different tunnels but my question is a crypto map and an eazyvpn on the same outside interface can it work.if yes, do you have a configuration example of the 2 hubs and the spoke?
View 1 Replies View Relatedi have cable internet. and im supposed to get up to 15Mbps. but i only get that on a good day. i average around 10Mbps.but im paying $60 a month for the 15Mbps. i can get at&t u-verse at 18Mbps for $39.95 a month for 12 months. then it goes up to $44. does any one her use U-Verse? and do you think its a better deal then cable?
View 3 Replies View RelatedOur PC and Modem were in storage for several months. When we unpacked and re connected everything, we could not get conected through our 2 wire modem. We have checked cables, brought other machines into the house , and still cannot get a DSL connection. We tried the proxy settings others have posted. I have not had a chance to see if I can ping any internet suppliers, but to me it seems like a problem with the modem itself.I am not very tech savy, but I am able to follow directions, to trouble shoot.Oh yeah called my Internet provider, and they said it was phone line problems, but phone works great. Didn't even walk me through testing the modem.
How to run different different Net connection run in one pC
View 1 Replies View RelatedI need to run a windows hyper terminal program between my POS register which has a serial RJ11 port to my PC db9 male port
View 2 Replies View RelatedI have a firewall behind 2 routers and 1 modem. I set the vpn up in the firewall and not getting a connection. Do I need to set something up in the 2 routers and modem for it to work?
View 5 Replies View RelatedDoes vpn connection need ISP support. If it does, in which step does ISP give service?
View 6 Replies View RelatedI just got my computer back after a friend removed a few viruses from my HD. My computer won't get internet anymore. It's connected to the internet at 54mbs but there is no packet transfer at all. I've tried winsock commands and netsh commands with no avail.
Details:
OS: Windows XP Service Pack 3
ISP: Comcast
Antivirals: AVG (I run Spybot when I need to)
Case: My home has few laptops and mobile phones connected wireless to the home's Router -> & to cable modem.
Problem: When I turn-on this particular HP's PC and connect to the internet (wireless) - the whole house internet connection becomes intermittent (e.g. OFF / ON). The Internet connection is fine (no problem), if this PC is not connected to the Internet (not connected to ie or google).
Trouble Shoot (without success)
- I have reformatted the PC and scan the PC with Malware in safe mode (no infection).