I have Mediacom cable and internet and I was trying to hook both up in the same room.When I connect it directly from the internet cord to my modem it works fine.But when I connect it using a splitter to hook it up to my modem and tv, only the tv works.So, how would I get this to work??
View 1 RepliesI have a desktop with a "black screen", but the computer is running. I need to get files/documents off that computer. How can I get them without being able to see the monitor? I have a netbook, a portable hard drive, and regular ethernet cables, but not a cross over cable.
View 1 Replies View Relatedhow to go about config my bureau connected to HQ and separated by a WAN link of 60mb.
This is my plansplit into halves that is 30 mb for LAN connections, internet and file serving for strictly video streaming, bureaus have routers 2800 conected to HQ HQ has a router 3900
Now I have a 172.16.0.0/16 network with a def. gw. for internet where is a MS Forefront TMG 2010 with BSplitter for traffic shaping. I purchased an 2921, 2,5 GB RAM, security+data license and an EHWIC-D-8ESG.
I made 4 subnets in a test environment with some access-lists, nothing fancy yet. How can I use FF TMG for bandwidth management, where should I put it? For those 4 subnets the def. gw. is, normally, the 2921 router. TMG is splitting traffic by client IP.
i connected network cabel to cpu network not geting ping also done,so can i check from multimeterLaptops internet connection keeps fluctuating
View 2 Replies View RelatedI have a modem which is allowing me to go online at home. Unfortunately, the cable that goes with this modem is too short (just 2m).This week, I bought a cable (internet cable) of 24m and I expected to be able to move around while being connected and surf the internet but internet does not work when I am using the new cable. We have tested the cable (using a cable tester) and the cable seems to work fine. When I use back the old cable (which is very short) internet is working perfect.
View 15 Replies View RelatedI just bought and received a Cat6 200ft Ethernet cable from Amazon, linkIt is going from a router to my PC and is not working. My old Ethernet cable works just fine from said router to PC. I do not know why this one is not working. I tested the cable out on my laptop and it works fine for that. I am not sure what info to post about my PC, but I am using an Asrock z68 Extreme3 Gen3 motherboard as my lan connector.
View 10 Replies View RelatedAfter running my malware anti-virus and removing all the virus, my Local Area Connection keeps saying network cable unplugged. I checked the network adapters and everything is fine. When I did an ipconfig, there's no ip address showing. I have Windows XP. I've tried almost everything and it's still not working.
View 1 Replies View RelatedI inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.
View 2 Replies View RelatedI have 128KB Dsl connection and two Computer i need to splite them equal. i mean 64KB for each computer, it's very annoying when another computer start downloading or something like that then my computer is totally down.
View 4 Replies View RelatedI have a little weird request at work. One of our offices would like to split the VOIP traffic. At that office we have a 10MB primary and 3MB backup circuit. Currently the phones are routing over the 10MB circuit. The General Manager would like to use the 3MB backup circuit for VOIP traffic. For the 3MB we have two T1 lines bundled together in a multilink. Configuration is bellow if needed
3MB Circuit
I'm trying to connect a second desktop to my internet connection. My current setup has my primary desktop using a wireless card and getting internet from the wireless router. Then I bridged the connection from my desktop to my xbox. Everything worked perfectly.
However, I recently got a second desktop(running lubuntu if it matters) and I'm trying to get it connected so that I can use Synergy and share a mouse with it. I found an old router laying around the house and was hoping I could use it to share the bridged connection to my xbox with the second desktop. Like this:
I couldn't get that to work though. The second desktop knew it was connected, but it couldn't connect to the internet. It would also throw off my primary desktop and it would try to connect to the old router.
I also tried to set it up like this:
Using an ethernet plug in the wall that normally just went to the TV and trying to split it there. The TV still worked, but the second desktop didn't.
How I can get this all working. I'd like to do it without having to order a wireless card/usb and just use what I have.
I have cable internet with 12 Mbit download and 1.25 Mbit upload speed. I'm using Thomson TGW850-4 router and I'm sharing the connection with my brother. Each of us have our own PC, of course.
Problem is, my brother downloads torrents while I play online games which completely screws up with my ping (from 40-80 to 350+) which makes them pretty much unplayable.
Is there a way to split the connection in two so that each of us gets 6 Mbit download and 0.625 Mbit upload at all times so that his torrents don't interfere with my online games?
Trying to split a supplied fixed IP address to multiple wireless devices so that I can piggy back on the internet connection in my office. Cause the IT dept refuse to provide a router.I plank to use a router for the job above.
View 4 Replies View RelatedIn one of our offices in Tokyo, we used to connect to the internet using a PPPoE connection from an ASA5505 and then ran multiple IP SEC tunnels to our remote sites. We have a /28 public range, but I couldn't work out how to utilize the other addresses, as the firewall was assigned a /32 on it's dialer.
To try to use more of the address space, we changed the topology and put a 1921 router at the internet perimeter terminating the PPPoE and then connected the inside of that to the outside of our ASA5505. We split the /28 into two /29 sub nets. the dialer interface of the router has a /32 from one of the /29s and the link between the inside of the router and the outside of the firewall used the other /29.
Since that change, we have had a number of performance problems to devices located behind the firewall (over VPN). If there's no traffic going over it, then response times to the public facing interfaces of the eqpt there are good. The more traffic we push over it the more packet loss we get. The response times are consistent, it's the packet loss that's the problem. There are no errors or drops on the PPPoE interface.The obvious answer to this is that we're pushing more traffic over it than we should, but it's a 100Mb circuit and I'm having severe packet loss if I try to push about 2 or 3 Mbps through it.
We're pretty certain that it's an ISP problem and can't say for sure that the problem started when we changed the topology out there, but anything to do with the way we've split the subnets out like that?
I have a pair of ASA5510 currently running as a failover pair. For some reason we need to move one of the firewall to another site, is there any best practice on splitting up the failover pair then I can re-configure the secondary unit offline?
I'm thinking to power down the secondary unit, unplug it from the network totally then erase the configuration on the secondary unit on console so I can re-configure it. For the primary unit, I will disable the faiolver config by "no failover" on the primary unit. Is that necessarily all thing for splitting up the failover cluster?
Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB(code)
I would like to connect to a 1Gb routed uplink, and then impose bandwidth limits (via shaping/policing/whatever) on a per port basis. The ports could either be configured to route, or as switchports on separate VLANS. I'm trying to identify hardware that will let me do this. The set up I have in mind is shown below.
I am wondering if the IP Services Adv software on that switch will allow that functionality?
I was wondering if the EA3500 would support splitting the USB (buying a USB tree) to allow for both a printer and hard drive to connect at the same time?
View 1 Replies View RelatedI have two ethernet cables, a long one and a short one. The short one works fine, but the long one does not work with my computer. It has worked with other laptops, so I am fairly sure the cable itself is fine - is there anything I can do
View 3 Replies View RelatedI am trying to connect a pc with a cable modem using a cat5 UTP cable.I initially checked all the wires of the cable with a meter and then punched the RJ45 connectors to both ends and also checked them with a cable testing device and the straight through mappings were correct, but when i connect the two ends to the cable modem the respective lights do not show up. I have not tried the wire from the pc to the cable modem yet. The cable length is 72 meters.
View 13 Replies View RelatedLog enabled using [URL] , config saved, modem power cycled...... no in and out log after internet use.
View 1 Replies View RelatedI am trying to upgrade the switches in one of the buildings to Gigabit HP ProCurve switches. Currently, this building has 3 wiring closets, and each closet has 2 Intel Standalone 460 switches (24 ports). We use them as simple Layer 2 Switches. Nothing fancy.We recently bought 3 48 port HP Procurve Gigabit switches.I was planning on going in and swapping the 2 Intel Switches out with the HP Procurve Switches. The first closet went fine, and we had immediate connectivity (servers, Internet, etc.). However, when I went to the second closet I found that I could not connectivity back to the first closet.I then noticed the patch cable going from Closet A to Closet B is terminated with a female connection on both end. And then a patch cable is connected from the end, to the switch at both sites. I have never seen this before. And I hope I am making sense. Why would this method work with the old Intel switches (that are close to 10 years old) and not with the HP?
View 5 Replies View RelatedI have the WCG200 and it has been working fine with my Comcast service for the last 4 years with no issues, either wired or wireless. Starting about a week ago, I have been having a lot of trouble with my wireless. I am on Firmware Version: 2.0.3.9.31-1023 and my ISP is Comcast. I have tried calling Comcast to see if there is a firmware update but that phone call usually doesn't go very far.
View 8 Replies View RelatedI just bought a macbook and want to connect with my WAG320N. I have no problem to connect on 54mbs what tells me that I'm on Wifi G. The settings in my router was on b/g/n so I changed it to just N but then it won't connect. I don't get error or nothing. I just doesn't connect. I tried all different kind of settings but no luck.
View 8 Replies View Relatedwhat do i need to setup in WAG120N to work with a Wireless Network repeater?
View 1 Replies View RelatedMy Ethernet cable connecting my computer to my router is not working. It was just working a few days ago and I have connected it to a different computer and it worked on that
View 1 Replies View RelatedAfter trying to communicate between an XP machine and Win7 using static IP and a crossover cable my wireless card stopped working. I did make the mistake of trying Homegroups prior to that.
It says Unidentified network and constantly remains in the Public Profile. Not even WiFi Sync is working...diagnostics reveal a problem with the drivers though several have been tried. From the originals to the latest version...Properties describe the device is working normally?
I have problems to make a PPTP vpn to my M0n0wall. PPTP passthrough is enabled, port 1723 TCP ist forwarded to M0n0walls WAN Interface. Rules on the M0n0wall are set correctly. It seems that the Linksys has problems with GRE 47 protocol routing. Does a newer model (WAG120N or WAG320N) work with PPTP passthrough?
View 5 Replies View Relatedi have Linksys WAG320N and Draytek Vigor 2850. My main router is Vigor, wchich support 2 WANs. First WAN is my VDSL connection (plug direct into Vigor) and second WAN i want ADSL connection. Can I work with WAG320N only as ADSL modem?
View 1 Replies View RelatedLike the title says, the wifi on my wag120n stopped working. It happened suddenly, nothing was changed in the settings. It stopped showing when i'm searching for wireless connections (SSID is still enabled).
View 3 Replies View RelatedI have some hardware on my internal network which I want to send udp packets. I can connect using telnet to it prooving that TCP and port forward works but when I try to send a UDP packet externally it fails.I can however send the same packet internally and port forwarding works fine.My router is Linksys by Cisco WAG320n.
View 2 Replies View RelatedI'm trying to open some ports for my webserver, I've configured the static IP and forwarded port 80 to my server's IP and I checked the port on canyouseeme.org and it says it's closed. I've tried multiple ports (21, 22, 7878 whatever) and all do the same thing.
So my next step was to try DMZ on the server's IP .. still no happiness .. ports stay closed. I checked this on multiple computers and it still won't open any ports for any machines on my network.
Updated to the latest firmware .. didn't make a difference. My ISP doesn't block any ports (didn't have any issues on my old router.
Signal drops constantly and seems to be a problem with the Mac more than the router IMHO but i thought to register the problem here.
I'm not alone as many users on the Apple support forum are experiencing the same drops via airport and with different routers.. Lan line works fine for me with no issues
I will update the firmware and try that as it seems i am running old firmware V2.00.13
