Wifi Works But Lan Doesn't?
Sep 21, 2012
I just recently bought a Telewell Wlan AP wireless access point and my problem is that I can't connect to the internet with Lan, hence can't get connection on my desktop. My laptop however works fine with wlan.
There's a wall socket which connects to a bigger student local network, I can connect my desktop to it directly and it works so there seems to be nothing wrong with my computer. I've had 2 routers before this, another Telewell that worked flawlessly and a Buffalo that cut the connection every now and then but didn't have this kind of problem.
I have the router plugged into the wall, set to get a dynamic ip (as it should be) and it does find Wan-side ip-address and dns-servers, as I could connect through wifi. So there doesn't seem to be a problem with that either. But for some reason Lan doesn't work. I can access the router through Lan, dhcp is on and I can see my desktop on the routers client list.
View 2 Replies
ADVERTISEMENT
Jan 24, 2012
I am running XP Pro SP2 Ver. 2002 on my laptop.,i use the wifi connection very well. But when i plug the rj45 cable in from the modem,the LAN icon says Little or no connection.
View 14 Replies
View Related
May 26, 2012
I didn't install new program or make a lot of change in my computer lately?Anyway here's the ipconfig/all result of my computer
Windows IP Configuration
Host Name . . . . . . . . . . . . : asus-95bdea2abb
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]...
View 3 Replies
View Related
Apr 4, 2013
I have been using my laptop since a year now and yesterday suddenly my internet stopped working. On top of the connectivity bar a yellow sign appeared. Now my internet status is "No internet access" but when i connect my ethernet cable the internet starts working and i can see the "Internet access" status. I have re-installed my wi-fi driver too from the orignal CD that i got with my laptop, but still no luck also i did not install anything in past 1 week and the only anti-virus i have is Avast (tried disabling it too). I plugged out the cables from my router and plugged them again but that dint work too. There are 2 other laptops (running on windows 7 just like mine) on which the wifi connection is working but on mine it is not working.
View 9 Replies
View Related
May 1, 2013
I have a E4200 v1, connected with a few PCs by ethernet ports and various devices by wifi. Now the wireless devices work perfectly but sometimes the PC via ethernet ports cannot connect to LAN and internet.
View 2 Replies
View Related
Jan 15, 2012
hen its wireless, it has no problems with the internet, everything works fine.But when its wired, webpages will still load, but youtube videos wont work, anything that consists of streaming doesn't work, and he cant even useI have connected other laptops to the same cord and there is no problems. so i know its not the cord and i imagine its not the router since everything still works fine with other computers.
View 5 Replies
View Related
Jul 21, 2012
My cable modem and router are in a closet. From there, wires run through the house to multiple locations. One of the locations has had a wireless access point (WAP) installed which has worked flawlessly. I want to put another device at that location that doesn't have wireless capability, so I tried to connect a switch. The switch does not connect. When I disconnect the cable from the WAP and plug it into the switch, the light on the switch port that would indicate a connection does not come on. When I then connect the WAP to another port on the switch, the light on its port does come on but it does not see the router. I've tried multiple cables (I even tried a crossover cable) and I've tried a second switch with the same result. When I plug back into the WAP, it works fine again. The switch works fine at other locations in the house.
One more thing - When I bought the house, the wire to this particular location was unterminated. I had never done any wiring before but I decided to try to do this myself. So, I read up on the process and bought the necessary tools. When I stripped the wires, I found that the twisted pairs were not just twisted (as they were in the patch cable I practiced on) but each pair was in a single strand of insulation (I'm not sure exactly how to describe this but there were four strands of plastic, each with two wires packaged inside.) I didn't know how to separate the two wires that were packaged together so I wired the connectors with all four color - color/white pairs next to each other. I know that's not the standard. But from what I read, as long as I wired both ends of the cable the same way, everything should work. And in fact, it did for connecting the WAP.
View 1 Replies
View Related
Sep 16, 2012
my internet works normally during daytime but starts to disconnect and reconnect every few minutes at around 11pm. I've tried restarting my modem but to no avail. My home telephone line is not working when my internet starts disconnecting and it starts working during daytime. My modem is connected to the telephone.
View 4 Replies
View Related
Mar 23, 2013
I have setup a remote access VPN to an ASA5505
I have a directly connected server behind the ASA and I can ping the server without a problem.
The VPN client reports packets being encrypted and decrypted
However when I try to RDP to the server the encyrpted packets keep incrementing but the decrypted packets do not.
I am also not seeing any RDP traffic hit the server (verified by ethereal)
I have done a packet tracer and it suceeds but ends with an IP spoof which I believe is correct as it is vpn traffic and not actually being encrypted.
This is the debug from the RDP session, I am confused by a Denied ICMP on line 2 as I am able to ping the server?
%ASA-6-302013: Built inbound TCP connection 88193 for external:172.16.24.4/50984 (172.16.24.4/50984) to internal:192.168.100.146/3389 (192.168.100.146/3389) (roger_ssl)
%ASA-4-313004: Denied ICMP type=0, from laddr 172.16.24.4 on interface external to 192.168.100.146: no matching session
[Code].....
The only logical bit to this is flow closed by inspection? Does this mean the server has not responded?
And the decrypt packets not increasing when trying to RDP Does this mean that I have reached the end of my ASA knowledge on this one!
View 6 Replies
View Related
Aug 22, 2012
I have a ASA5520 with 4 Port channel interfaces and ASA Version 8.4.(2). There are many vlan interfaces but in the DMZ I have one Server who has a Static NAT to all other interfaces.
Why the first ping works and the others doesn´t work?
View 12 Replies
View Related
May 15, 2011
I need remote access to certain programs on my home PC but I just cannot get it to work.
Program:- webcamXP
When I set the programs port preferences (i.e. port 8087), I can connect with"127.0.0.1:8087" and webcamXP work fine. But when I replace the localhost with my external IP (lets say 79.149.114.227, so that would be "http://79.149.114.227:8087".I tried port forwarding: I have added the port to my NAT in the router's setting so it should be fine, but it is not (numbers are fictual of course):
external port start 8085,
external port end 8089,
protocol TCP/UDP,
internal port start 8085,
internal port end 8089,
server IP address 192.168.1.215)
I also tried disabling AVG Internet Security 2011's firewall temporarily just to check it it was blocking it, but got the same result.I checked if Windows own firewall was on, but it is off.I cannot find any setting in the router's own configuration screen to disable any build in (router's) firewall (if it has any).
View 6 Replies
View Related
Mar 13, 2013
I try connecting via ethernet cable and it doesn't seem to work until the administrator of the network (my brother) comes home and then turns his computer on and starts using it. However, if i switch to a wireless adapter it sometimes works (like right now) even when my brother is not using the internet. Also, i tried to connect via wifi on my macbook pro to the same server and it used to work flawlessly 100% of the time, now i can only connect once in a while for short periods of times.
View 1 Replies
View Related
Dec 25, 2011
I'm trying to set up a wireless network for my parents. I have a Belkin Play N600 router (model F7D8302) that I'm trying to hook up to an Acer desktop running Vista. The modem is a Siemens Speed stream 4100. I have a cable going from the ethernet port of the modem to the modem port on the router. The pc is connected to one of the other four ports in the router. The wireless works fine, but I can't get the wired connection on the desktop working. The Internet light on the modem is not on, but the modem works fine when connected directly to the pc. I've tried power cycling and resetting everything, but it's still not working.
View 9 Replies
View Related
Nov 17, 2011
I have a Cisco linksys router e1550. My wireless network is working fine, but my wired (PC) is not working?
Removing the router and having the modem connected to my PC works but when I put on my router my wired connection only works for a few seconds to none
So I think the router may be causing it, could it be the settings? Even though there at default.
View 1 Replies
View Related
Nov 28, 2012
I have a win7 desktop upstairs with all of my media on it.I also have a winXP laptop that I would like to use as a media center running xbmc connected to my tv downstairs.I have set up a workgroup so my laptop can access the media stored on my desktop and everything works great when they are both hardwired to my router (Linksys E3000).However, as soon as I unplug my laptop from my router and switch to the wireless connection I can no longer ping my desktop or access the shared folder (internet still works fine on the laptop, it just cant see my desktop anymore).If I plug it back in to the router, everything works again.
The exact error message I get when I try to access the shared folder is "\INFINITYMedia is not accessable. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. [code]
View 14 Replies
View Related
Nov 16, 2011
About 6 months ago I bought a new router (Linksys E1000 v2.1) which worked great right out of the box. A couple months later I tried to setup a home network so that my two laptops could access a shared drive on my wired desktop, but for some reason they didn't show up as being on the same network. All computers involved are running Windows 7 if that matters.
Upon a recommendation from I friend I put DD-WRT on the router and it worked fine. Setup MAC filtering and WPA2 Personal security. This worked fine for about 4 months until today.
When I got home from work today I noticed my laptop wouldn't pull up any web pages, but it said it was connected. Then I noticed my iPhone wasn't connected either. I restarted my laptop and then it wouldn't connect to the wireless either (I could see the wireless, but I would get a Could not Connect error when I tried to connect to it).
I went to my desktop and it is working just fine, it is plugged into the back of the router. I also have an AT&T MicroCell (cell phone booster) that is plugged in to the back of the router and it works fine too.
I removed the encryption and MAC filtering. I then reset to factory (or "factory" DD-WRT) and now the wireless works, but it is MUCH slower than my desktop. I ran a speedtest on my desktop and got 12 Mbps down and 1 Mbps up. On my laptop, I get 0.03 Mbps down and 0.25 Mbps up.
View 4 Replies
View Related
Dec 24, 2012
Region : India
Model : TL-MR3420
Hardware Version : V1
Firmware Version : 3.12.21 Build 120523 Rel.37880n
ISP : Reliance
I've just set up a MR3420. It works fine in "WAN only" mode and provides access via our ADSL modem. It also works fine in "3G only" mode and provides access via a Reliance Netconnect+ USB modem (a Huawei E150 I think). I updated the firmware to the latest version in order to get it to work with the USB modem.
The problem I have is that when I set it to "3G preferred" it doesn't seem to connect over 3G. I can see it tries to connect but then fails and then WAN takes over. The connect and disconnect options are greyed out on the 3G page so I am unable to manually get it to retry. I've tried leaving it for a long time but it doesn't seem to connect over 3G ever. I've tried setting 3G to connect on demand and connect automatically but both behave the same.
View 3 Replies
View Related
Nov 5, 2012
I've got a 3560-X that passes POST according to console, but there are issues nonetheless...USB console doesn't work. RJ45 works just fine. No status lights turn on at any point (e.g. syst, xps...). 10g network module is installed with a 10g LRM SFP. All lights on the module are amber. However, it passes according to POST. Switch passes traffic, obeys config, etc. Link lights on RJ45 ports work fine. This was brand new out of the box. Thinking about trying IOS reload..
View 6 Replies
View Related
Apr 18, 2013
I have a pair of OLD Cat6500's running CatOS:
WS-C6509 Software, Version NmpSW: 7.6(16)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Dec 22 2005, 16:37:19
System Bootstrap Version: 7.1(1)
System Boot Image File is 'bootflash:cat6000-sup2k8.7-6-16.bin'
System Configuration register is 0x2
I know these are no longer supported, but I have to ready them for migration. Recently a problem began with these switches. What happens is that when I telnet to them, I cannot authenitcate via TACACS. This works fine for all our other IOS equipment, just not for these 2 switches. The error is:" % Error in authentication" and then I get kicked back to the login prompt.
The odd thing is that when I connect to the switch via the console port, I can authenticate fine with TACACS.
CMS> /c 14
[Code].....
View 2 Replies
View Related
Feb 10, 2011
My pc will not pick up the internet, my iPad does through my wifi. I called my provider and they said my connection is fine, they mentioned not using a USB cable but when I take it out my wifi won't work on my iPad. My pc keeps saying not connected to the internet. I have a modem and a router, do I only need 1 maybe?
View 1 Replies
View Related
May 17, 2012
My computer worked fine on the eithernet, but I had to move it to a different room and now it won't recognize ANY WIFI connections. I know the wifi is working because I have laptops and phones connected to it. the computer is only 8 months old. It's an HP Pavillion AMD Phenom II 820 Quad-Core Processor, Windows 7 64 Bit, Wireless LAN 802.11b/g/n.
View 19 Replies
View Related
Oct 26, 2012
Had talk talk router upgrade yesterday and everything worked fine. Today wifi works on MacBook but not on PC Windows xp3. It appears in the list but won't connect on pc. Can connect to an unsecure weak connection on the list but it's not mine. Been in to router to chnage channel from auto to 11 as an eg
View 2 Replies
View Related
Apr 7, 2012
I can't seem to connect to the internet via the Ethernet port on my laptop, but the built-in Wi-Fi card works perfectly fine. I normally use Wi-Fi, as our signal is very strong, even if I go outside and up the road, I can still connect.
My issue is that although I don't need it, I'd like to setup Ethernet for the first time since installing Windows 7. I've had Windows 7 since April 2011, and prior to that I used Windows Vista. From memory, I don't think Vista had any problems with connecting via Ethernet back before I moved house, but this was over two years ago.
My laptop is an ASUS X58L, and the NIC identified by Device Manager, is a Realtek RTL8139/810x Family Fast Ethernet NIC. Going into the properties, I can see that I have the latest Windows 7 driver installed - 6.111.723.2009, however prior to this I had the driver that came with the machine (when it was running Vista), which was 6.108.331.2008 and tried updating from Device Manager, but for some reason it said that I had the best driver already installed. To install the 2009 Windows 7 driver, I had to manually download it from Realtek. With either of the drivers, connecting via Ethernet doesn't work, and I'm confused as to what to do next.
View 13 Replies
View Related
Aug 11, 2012
I have a computer connected by ethernet to a netgear router. >Today it has decided it doesn't want to connect to the internet.When I try to connect it justs tells me it can't find the server.
View 6 Replies
View Related
Mar 19, 2013
Yesterday, My internet kept failing when i was watching youtube videos,so i had to keep toggling the wifi on my laptop. Now ,my network keeps saying no internet access, yet my phone has no issues with the wifi. No, i dont have or use Mcafee. I ran malwarebytes but it didnt find anything. Superantispyware keeps crashing (I dont run both at the same time.)
View 3 Replies
View Related
Feb 9, 2013
my computer just randomly stopped connecting to the intenet. I checked my other computers and phone and found they were all working fine. I was having internet problems pior to this happening (internet was being very slow and some web pages and some videos wouldn't load. I think the latter had to do with flash player though.) I had also been doing some stupid stuff on my comp that I know can give you viruses. Furthermore I also knew that due to previous virus's I was not able to do a restore. So as you have probably gathered my computer was pretty buggered even before this problem. So decided to restore to factory default using some backup images I made when I first got the comp. That went smoothly however the internet stilll doesn't work unless I plus it in using a ethernet cable.
View 9 Replies
View Related
Aug 16, 2011
the name of my wifi network changed and I do not know why, therefore the password for the former name will not work with the new network name
View 1 Replies
View Related
Nov 26, 2012
My laptop works fine on my network for 80% of the time but the rest of the time I get yellow triangle and the system says limited access. The annoying bit is that when this happens my smartphone is still connected to my wifi network and works perfectly so I can only assume there is a fault on the laptop. I take out the network adapter plug then plug it in and the laptop usually reconnects but sometimes it can take about half an hour!
My laptop is an acer aspire6935 and the operating system is windowsvista home premium. The wireless router is connected to a desktop via a yellow data cable.
View 1 Replies
View Related
Oct 5, 2011
lost wireless to all wireless devices (laptop, iPhone and iPad). Still have hard wired ethernet internet access from desktop. Tried resetting router, powering off router, resetting and powering off cable modem. Nothing works. Lights on router all on.
View 1 Replies
View Related
Jun 2, 2011
815 is setup & works computer is connected to wifi but I can not surf the net I am using a Amped UA600 usb adapter I have no idea why I still not not surf the net?
View 1 Replies
View Related
Mar 3, 2013
Region : India
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 4.0
ISP : BSNL
i have bought TP-Link W895IND and frequently the WIFI is not working. Everytime i have to active and deactive. Now since last one day it totaly stoped working . WIFE icon is glowing continously without flickering.
View 3 Replies
View Related
Nov 9, 2012
I have Lenovo laptop and my internet works just fine when the cable is connected but Wifi does not work. It shows that i have excellent signal on the side but it just wont connect. When i type in password it says " Windows cannot connect to XYZ ". I use Windows 7 and my wireless network adapter is Atheros AR9285.
C:UsersMY>IPCONFIG/ALL
Windows IP Configuration
Host Name . . . . . . . . . . . . : MY-PC
[Code]......
View 14 Replies
View Related
Jan 6, 2013
I have an E1200 model 1 router. I've owned it for over a year and it's given me no problems until now...Hardwired ethernet connections work fine, but the wifi no longer works consistently. I have several wireless-N wifi devices that either cannot connect to the router at all (they present an error message), or do connect but will not load anything over the connection, or will load web pages very very slowly and then suddenly drop the connection.When I go to the DCHP client table, I see all of my ethernet connections but it does not show any wifi devices, even if the WiFi device is showing a connection to the router.The wifi connection is secured via WPA2 Personal.I have tried changing channels to one that was not congested with any other nearby routers. I have also tried a 30-30-30 factory reset. I am updated to the latest firmware version (1.0.03). I am sure I am entering the correct pass phrase to connect over WPA2. All of my wifi devices are confirmed to be wireless-n, not g or b.
View 7 Replies
View Related
