Wireless Bridge With 2 Routers Sagem 2504N / Netgear DG834GT?
Mar 8, 2013
I am on Sky broadband and have got the new Sagem 2504N router and have the old Netgear DG834GT router set up in my bedroom as a 2nd wireless hotspot and was wondering if it is possiable to set the netgear as a wireless hotspot/bridge to boost the range of the existing wireless signal rather than having two diff wireless hotspots and having to manually change between the two ? They are both ADSL routers, obvi the Sagem 1 being the 1 connected to the telephone line and the Netgear 1 being used "Passively" via a CAT5e cable from my switch i have in my bedroom?
View 8 Replies
ADVERTISEMENT
Aug 9, 2011
how to connect 2 routers that both have an ADSL connection. When attempting this the Belkin router will lose the ADSL connection after a random amount of time.
View 5 Replies
View Related
Feb 23, 2011
I have a weird problem with my network setup. I have a netgear DG834GT ADSL router which runs fine with my Belkin 51B64C wireless router but when I enable "Use as Access Point" in order for me to see my wireless laptops connected to it the internet performance goes bad, the traffic cuts out momentarily for about 7 seconds at a time, its pretty difficult to surf the net having to wait.The setup is as follows:
Netgear
Gateway IP: 10.0.0.1
Subnet Msk: 255.255.255.0
DHCP Enabled
Belkin
Gateway IP: 10.0.0.9
Subnet Msk: 255.255.255.0
DHCP Enabled
as I said above the reason I enable "Use As Access Point" is so I can see the devices in Explorer for file sharing. Is there a way I can use port forwarding on the router to see the devices it would solve the performance problem.
View 15 Replies
View Related
Aug 9, 2011
I have two routers. One is Netgear WG602 v3 and Netgear WNR2000. WG602 v3 is connected with internet. I want to make a wireless bridge. How?
View 1 Replies
View Related
Aug 23, 2012
I've got an old netgear dg834g router and I want to set it up so that it connects wirelessly to the main router in the house (netgear dgn3300) in order to have wired connections from the old router to my pc and xbox 360 upstairs.
I think I need to change the setting on the old router so that it acts as a 'repeater with wireless client association' but on the most recent firmware this doesn't seem to be an option.
I've been trying to use this guide [URL] but it doesn't seem to work. Whenever I change the IP address of the old router it just breaks down and won't let me access the settings anymore.
View 2 Replies
View Related
Sep 15, 2012
My router isn't allowing any wireless connections. I just woke up and my router was refusing connection to my wife's laptop and both our Nintendo 3DSes. However, my Xbox and my PC are directly connected and work perfectly. The laptop keeps saying my passkey is wrong.
View 2 Replies
View Related
May 9, 2012
I have a Cisco 881W and I would like to basically some how bridge the Cisco router to my netgear router. This is what I'm trying to achieve:
Cable Modem ----> Netgear Router ~~~~~ via wifi ~~~~> Cisco 881W ------> FastEthernet Ports
I've tried setting the Cisco 881W with station-role non-root with the SSID of my netgear router, but I get the error %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response whenever I try to bridge it.
Is bridging the Cisco router via wifi to the Netgear Router something that is not possible or is it an error on my part?
View 2 Replies
View Related
Jul 8, 2011
My primary home wireless is a Linksys WRT54GS Broadband Router. I have an older Netgear WGR614 Wireless Router that I would like to setup as a wireless bridge to use in another room to connect my other electronics to (i.e tv, blu-ray, Wii).
View 3 Replies
View Related
Feb 18, 2011
WAG320 allows website blocking, to enable this you can use a keyword. I would like to use this function to block anoying advert sites (in the same way I could with my Netgear DG834GT) - However the way this function has been implemented is less than ideal.
e.g. when a site is blocked by the router, the router does not return a response - this is great until that site forms only part of a web page that is permitted. What then happens is the web page takes forever to load as the responses have to timeout for the blocked components.
The way this function *should* have been implemented, is the router should return a blank response for each of the blocked sites. Netgear do this and it works a treat, they even put up a banner saying "Website blocked by Netgear".
This is such a simple feature, why has Cisco overlooked this and how do I go about raising a product enhancement ? I've been through the helpdesk which quite frankly is a farse, they asked me to reflash my firmware which surprisingly didn't resolve the issue - they then told me to send them the unit back because it must have a fault !?!? (and I have to pay for postage of course!) I explained the issue about 5 times, but the operator on the other end was just a script reader and I could not speak to an engineer - very poor.
View 2 Replies
View Related
Jul 21, 2011
I've had my Sagem router running sky broadband for about 7 or more months now, but yesterday the connection began to drop randomly after connecting for like 40 seconds. Then It will come back on again 1-2mins later,they asked me unscrew my phone line covers to check yo see if it was a direct line. Eventually they told me that they would pass the issue onto their experts and would contact me in 72 hours, however after reading the exact issue that someone else had and he didn't receive any contact.
- My desktop is connected via Ethernet and I have 2 laptops which also cannot connect to the Router.
- I don't recall any changes I've made to the network, that might have caused these problems
View 10 Replies
View Related
Jun 23, 2011
I have infrared on my sagem myx-7 and want to transfer my photos to my netbook, I turn on the infra red on the phone, but the netbook doesn't detect it.
View 1 Replies
View Related
May 1, 2011
I have been having trouble forwarding ports for different softwares and servers. I just upgraded my internet and my ISP sent me a new modem/router all in one. I am using a wired setup to my desktop. The router I am using is Sagem FAST 1704.
My ISP told me that they only give support for game consoles, the dumbest thing I ever heard since I don't pay for their internet so I can play games. Cannot forward a simple port. Port 100 in specific.
When I forward ports, I am certain that I'm typing in the right Ip address digit because I checked ipconfig. Then I check the 'canyouseeme' website and it tells me that the port is not open on my ip address. I have tried other means of checking to see if the port is open but they all tell me the port is closed. Once in awhile the port will be open but most of the time it isn't.
I plug in my older modems and it doesn't make a difference when I re-set up the port forwarding to the new IP so I guess it isn't a problem with the modem or router. I changed all my ethernet and phone cords and filters as well. My isp told me that they do not block ports.
My isp is Windstream. I cannot set up a static IP in network connections because when I do the internet doesn't work at all even if I set the exact same settings that are currently set. This happens with both modems I have. I do not use two devices at one time just the modem or the modem/router, there are no other computers connected and filters are on all phones/satellites. I am using Windows XP, not sure what other info you will need.
My isp keeps telling me they do not support setting up vpn's. I do not need support for that I just want to open a port. lol the next thing they told me is, you guessed it, "We do not support setting up VPN please contact your work IT........" which doesn't exist. I spoke to three of them and they all said the same thing, except one told me they were going to open ALL ports for me. That didn't happen.
View 7 Replies
View Related
Jun 15, 2011
Everyone's 2wire works in bridge mode of they follow these steps url...but when i try i get no internet connection nor does it pick up any internet activity. I even input my account and dsl password in the netgear router gateway still no luck.I'm trying to use the netgear router because in my room i only get 2 signals bars and if i switch to the netgear wireless N router the signal strength would be alot better.
View 7 Replies
View Related
Jun 8, 2012
Can the rv120W be configured as a wireless bridge? We have a need to configure a vpn connection to a remote building but will need to connect the router via an existing wireless network.
View 4 Replies
View Related
Nov 23, 2012
I have just bought a n300 everything works well except i cant get my sky on demand wireless bridge to work , sky have said all ok, as have my broadband supplier. im told i need to maybe change my wireless settings in router !
View 2 Replies
View Related
Sep 14, 2012
I installed DD-WRT on my router and placed it in bridge mode, configuring it with what I thought was my Androids IP address for the gateway. I tried with the Android IP address identified through cmyip.org, 208.54.32.156, and with the one identified through ipconfig command, 192.168.43.1. Neither address was successful. Also, I am unable to access my router using the IP address that I manually assigned to it.provide some assistance on the process of bridging from an Android to a wired PC through a router, Linksys WRT54G v3,
View 1 Replies
View Related
Jan 4, 2012
If I have two Linksys wireless routers in my house, ( 1 Wireless-G as the Gateway attached to the DSL line, and attached to the main computer, and 1 Wireless-b model BEFW11S4v4 that I want to use as a bridge or as a repeater to send the wireless signal around the attic (2 floors away) and I have connected them via Ethernet, and then connected to the attic computer (not the main one) via Ethernet to Wireless-B, why can I not get connectivity on the attic computer?
If I forgo the Wireless-B router, and connect the ethernet to the attic computer everything is fine, but there is no wireless signal in the attic. (only downstairs where the Wireless-G is.) I believe I can access the Wireless-G and tell it to be a bridge or a repeter (?? I think) but as far as I can tell the Wireless-B is giving itself the same IP address as the Gateway Wireless-G is using, and I don't have an connectivity, so I can't change it! Im confused.
View 1 Replies
View Related
Jun 13, 2011
modem
........ |
........ |
----switch-----
|................ |
|................ |
Router 1.... Router 2
|..................... |
|..................... |
Computer 1.....Computer 2
......................Computer 3 Router 1 points to a VPNRouter 2 access to the internetComputer 3 needs to access router 1 (VPN). Both Computer 2 and 3 are in a different room than computer 1, and router 1. Computer 2 is networked via cat5e to router 2.Is is possible to have Computer 2 and 3 share the cat5e, yet access different routers?
View 5 Replies
View Related
Dec 31, 2012
Is there a way to Bridge N600 DB Wireless Dual-Band N+ Router F9K1102?
View 1 Replies
View Related
Apr 26, 2012
i want to ask if i can link two routers while they are totally separated of each other over the internet to make a large LAN the two routers are TP link?
View 5 Replies
View Related
Jul 2, 2012
My netgear wireless router (wgr614v9) wont reboot or let me access the internet what should i do.
View 2 Replies
View Related
Jun 13, 2012
I've two routers, one which i got from BSNL when opted for internet connection. Its a Utstartcom Type II wireless modem and the other which i got from a friend is Netgear WGR614 wireless modem/router.Now coming to the real picture. I've the BSNL wireless modem connected and working perfectly on the 3rd floor on one PC, but NOT configured for wireless access and i've another PC on Ground Floor where i need an internet connection. Fortunately, i got a router/modem which is Netgear WGR614. I do not want a wired connection between these two PCs then wanted to try the wireless way?
View 1 Replies
View Related
Feb 27, 2011
I have a Netgear N300 Wireless Router (WNR2000), and I am trying to connect the internet through it. The internet light stays amber, and though the router recognizes it, I can not connect to the internet. My computer also doesn't seem to recognize the router at all. Installation CD will not work either.
View 3 Replies
View Related
Jan 14, 2012
I was just wondering how to wirelessly bridge 2 routers so that I don't have to drill a big hole through the wall!! I have a netcomm router which is going to be the receiving modem and a net gear modem to transmit the wifi.
View 1 Replies
View Related
Mar 4, 2012
I live in a school residence with a roomate and we both have an internet connection in our rooms but it's two separate networks since we can't see eachothers pc on the network. Both our pcs are connected to a switch and those switches are connected to the two internet connections. I would like to know how to bridge those two networks using a router in the living room. I would also connect a printer and an xbox to the router so we can both access the printer, the xbox can access both pcs and we can access eachother's pc.
View 3 Replies
View Related
Mar 20, 2011
Is it possible to put the SRP 527 into Bridge mode to use it just as a modem?
View 6 Replies
View Related
Apr 26, 2012
I need to configure a rv120w in order to make it work at the same time for data and digital tv. The fact is that the set top box for the idtv needs an IP address that will be delivered directly from the ISP. So I need to setup one LAN port that will be bridged to the WLAN connection (the stb will be connected to that lan port), and another port that will be connected to the LAN swicth so that the rest of the network has internet access. I can't see anywhere a way to create such a bridge. Quite disappointing as it's possible to do so on open source platforms such as openWRT..
View 3 Replies
View Related
Oct 17, 2012
I have a Linksys E4500 as the main router and would like to use the WRVS4400N as a bridge to extend the range of my network and also attach a NAS to it. Is this possible? I've been trying different options but have been unsuccessful.
View 1 Replies
View Related
Dec 10, 2012
At the small church I attend, and where I'm the IT guy, we have an RVS4000 router which has worked well for us including the VPN capability. Our internet connection is through AT&T (not my choice) and last week we had to switch from DSL to U-Verse because AT&T is doing away with the former.
Unfortunately as part of this switch, the old modem was discarded and an NVG510 installed. The NVG510 is a combo modem/router. But since it doesn't have VPN capability and is not as good a router all around as the RVS4000 (even though the 4000 is an aging device), I am trying to run both.
I finally figured out how to set up IP Passthrough on the NVG510 so now VPN is again working to the RVS4000 so that's not an issue. We do have a couple of PCs that are in a room where no wired connections are possible so they are using wireless. But they are not very close to the wireless antennas so they don't have the greatest throughput. The NVG510 does have wireless capability and is physically located to where it would provide a much better signal. However, the NVG510 will only use a 192.168.x.x subnet and our LAN is setup for 10.x.x.x. I'm not about to change the LAN as it runs a Windows domain with enough equipment that I don't want the exercise of changing subnets.Can the RVS4000 be setup so that it will route domain traffic between the 2 subnets? As it is now, connecting a PC to the 192.168.x.x subnet on the NVG510 allows it to have internet access but it can't access domain resources on the 10.x.x subnet. I don't understand networking well enough to know why this won't work. I know it can because when I worked for a large corporation, they had different subnets that were routed so that PCs on one subnet could be on the same Windows domain as PCs on another subnet and all access resources on both subnets.
The RVS4000 may be capable of doing this but my limited knowledge of networking (I know servers, not switches, etc) means I'm not sure of what I see on the router to know if it can do it or not.I'd be appreciative to know first off if the RVS4000 can do it, and secondly if it can, then how to set it up. I've worked with the RVS4000 since we got it 3+ years ago so I'm fairly familiar with it, I just don't know the rest.
View 1 Replies
View Related
May 1, 2012
I have the Cisco RV082 with firmware v4.0.4.02 Comcast is connected to Wan 1 and works perfectly.I've enabled load balancing and am trying to get verizon DSL to function on wan 2.My verizon DSL line is connected via their provided actiontec GT784WNV router. I've enabled transparent bridging on the actiontec router and have PPPOE set up in Wan 2 on the RV082.
Wan 2 shows the following information, but will not connect to anything.
IP Address : 108.34.xx.xx
Default Gateway : 10.4.53.1
DNS : 71.242.0.12
Dynamic DNS : Disabled
I'm able to ping and traceroute most sites.
View 2 Replies
View Related
Apr 14, 2012
Lately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.
View 4 Replies
View Related
Dec 28, 2012
I have a N300 router I would like to put in another part of my house to repeat the signal from my N600 at the other end of the house. Is this possible? If so, how do I set up the N300?
View 2 Replies
View Related
Jan 27, 2012
My ISP insists that in order for me to have a home network use their router/modem ("2-Wire") for internet access, I must make my own network router act as a bridge since their modem is acting as the router. I.e. she said put your router into bridge mode. I don't know how to do that and Linksys won't offer assistance.
View 6 Replies
View Related
