I've recently had to unplug my modem and wireless router every time I want to connect to the Internet. Charter suggested that the modem signal was weak, indicating the modem might be bad, so I replaced the modem. The problem persists and they think the modem and router connection is timing out.They want me to lease a modem/wireless router combination for $10 a month. I'd rather buy one.
View 1 RepliesEvery day or 2 my VPN times out. It still says "connected", but I cannot connect to anything thru the VPN. Once I disconnect and reconnect it works fine?how I can keep this connected at all times without having to go through this process every day or 2?
View 1 Replies View RelatedMy Netgear adapter will not join the wireless network and keeps timing out.
View 3 Replies View RelatedI have an HP 8710 Workstation laptop running WindowsXP that just recently starting having problems maintaining an internet connection with my ATT Elevate mobile hotspot. My internet connection will work for 1-2 minutes and then end up timing out. I then have to disconnect and then reconnect to the wireless network to get connectivity. I was using was my laptop's built-in wifi card (Intel Wireless WiFi Link 4965AGN) when this was occurring, then switched to a wifi adapter (Linksys AE1000) and still the problem persists. I contacted ATT and they checked the cell towers, nothing is wrong and everything seems to be working. I've tried upgrading all the drivers, still no success.
View 1 Replies View RelatedI am setting up a new Guest network with a captive portal and it seems to all work fine except when Apple devices go to sleep. When they come back on it isn't just a case of logging in again as it just indicates to the client that it is still connected and won't present the login page again. The Controller will show the client as auth required. So far the quickest way has been for me to delete the network on iPads and re-enter my settings or create a new profile on a Macbook and join again. I have also had some success when doing a manual DHCP refresh on my Macbook which sometimes seems to kick the Controller into action so it presents the login page to the client again. Whether it is related to the timers on the Controller (5508 running code 7.0.235.3) or - as I just read in another post by Leo - the 20 minute timeout that all Apple devices have built in to conserve battery life
View 3 Replies View RelatedI'm running Mozilla firefox on xp 2. I hv wireless connection. My signal strength is very good. Under wireless network connection status my speed is 45 Mbps. Status is connected. Under activity it says is sending n receiving packets. My Internet used to disconnect n I'd restart it fixing it but now i'm having hard time getting it to connect. It keeps timing out. I hv to repeatedly click on links for them to work. Iv tried repair. Iv messed with dns n how grabbing ip address. Iv messed with Mozilla connection settings nothing seems to work.
View 4 Replies View RelatedSince yesterday I just get the timeout message on a few websites. "The connection has timed out. The server at is taking too long to respond." It's not just my browser or my computer. The other two computers on the network can't access them either.
View 17 Replies View RelatedSome websites, such as Amazon and Verizon's forum suddenly started timing out. This occurs on chrome, IE, and firefox. My xbox says it is connected to the modem but that it is not connected to the internet. My kindle fire cannot connect, but my android phone could load some websites, but now it can't load any. My mac, my laptop with windows XP, and my desktop with windows 7 are having the same problem. I did an upload/download test and the times were normal. I also restarted my modem, with no change. Other strange changes are that the wireless signal is weaker and it was slowing a few hours before it stopped showing some websites. Also, io9.com will load, but only the text of the nav bars. There are no graphics or other information. This has never happened before.
I have not done anything new manually to the modem or my computers. The only significant change was a power outage due to heavy wind that occurred a little over 24 hours earlier. I'm so confused by this that I don't even know what else to look-up or test. Why would a bunch of reliable websites suddenly time out while others still work? I don't think I can blame it on the servers of those web sites because the other sections of Verizon.com work, and student.santarosa.edu loads, but online.santarosa.edu does not load
I have a WCS and it's GUI keeps timing out on me, I have to login again and again if i do keep it idle. Anytime timeout for session into WCS?
View 2 Replies View RelatedI am having a major issue, system wide with web pages timing out or loading slowly - we are using a Sonicwall as our content filter and firewall and to assign DHCP, we are a windows environment with both Server 2003 and 2008. Here are the results of a few tracert commands I ran.
C:Userscaleb>tracert Google
Tracing route to Google [72.14.204.103]
over a maximum of 30 hops:
1 3 ms 3 ms 3 ms 10.240.163.121
2 4 ms 3 ms 4 ms 67.59.235.245
3 * * * Request timed out.
4 6 ms 5 ms 6 ms 64.15.1.169
[code]...
Recently, I've been getting problems where my internet browser is unable to connect to the server it's looking for or gets timed out. It happens intermittently (probably every five to seven web pages I try to visit), and refreshing after a few seconds always allows it to connect fine. It happens at some point on every web site I try to visit.This began occurring rather suddenly on both of my home computers. All other connections on these computers seem to be working fine. I use Chrome as the primary browser on both computers, but have tried using Firefox and it still seems to occur.What can I do to figure out what the problem is? I'm not even sure if it's a browser issue or a network issue, but we have never had this problem before
View 11 Replies View Relatedit keeps repeating 2 messages then timing out
View 1 Replies View RelatedMy Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
View 1 Replies View RelatedWhen I click on certain links, the webpage doesn't load, and I can't access that page only until going to it later.
Sometimes it says "no data received" and sometimes it gives the usual page for no internet connection
I am having a recurring problem with tcp sessions timing out / getting reset. I'm using the DIR-655 with PPPoE on a Qwest DSL line. Everything appears to be working fine (including my ipv6 tunnel) except for this issue where my long running ssh & database connections are being reset after a period of time.Currently have 2.03NA loaded, tried using 2.07NA but couldn't get ipv6 working correctly with the newer version.
View 7 Replies View RelatedIt works on the mobile site at times maybe twice a day but only able to access for 10 minutes maximum. I tried the command prompt and ping facebookm and noticed that I didnt recieve files back and it was just timing out is that whats causing it?
View 3 Replies View RelatedI have recently installed a new Cisco SG 300-10 switch--running in layer 3 mode--to function as a basic router for a new subnet installed at one of my company sites. When we attempt to ping devices on the 15.120.204.0 subnet from the 230.20.1.0 subnet, each device gives 2 responses and then times out continuously after that. If we wait long enough (thus far, an undetermined period of time) and reattempt to ping the same devices, the same thing occurs. Otherwise, we get nothing but timeouts. This occurs regardless of where we connect in the 230.20.1.0 subnet including VLAN1 on the SG 300-10. However, if we connect into VLAN 2 on the switch and assign a static IP, those same devices respond continuously. I was thinking that this must be a security setting of some kind but I'm unable to locate anything in the SG 300-10 that would appear to cause this.
View 1 Replies View RelatedRunning ASA 5510 with code 8.3 in it.We have our few https portal and OWA websites in HO.We access these sites from the network behind the ASA.All works perfectly fine.
In order to have control on internal network traffic we placed a web-filtering device (Fortigate) in transparent mode.To start with of we haven't blocked anything via new box but https portal and OWA stopped working from certain computers.At the same time other https sites were reachable from the same computer/s.We checked that website was tracable using traceroute from ASA,Fortigate and even from interal computer(from the one which it is not opening).This behaviour is random.
I have a E2500 router and 3 WAP610N access points. Users are having a difficult time connecting to the AP's. The client device just sits there trying to obtain an IP and then times out. If they get within range of the actual wireless router, then connect instantly. Is there a setting to increase that will allow longer time trying to obtain an IP?
I am using the same SSID for roaming, but am using different channels (1, 6, 11) for the overlap. See diagram below. Not sure if this has some impact?
i just bought a Netgear WNDR4000 router due to troubles with my current modem/router combo (D-Link DSL2730-B). The router doesnt have in built modem functionality obviously so I need to set up the modem/router as a dedicated modem.Also should I use the current modem/router as the dedicated modem or an older model i own (I think its a DSL 502T)? Because the current one often drops the internet connection. Don't know if its a problem with the modem functionality or something else. Will the older one serve better since i didn't have any problems with that one or will it be outdated? I only upgraded due it not having wireless capabilities. Otherwise it's fine.Or will I be even better off buying a dedicated modem? I really don't want to spend more money but if this is a far better alternative I guess i will.
EDIT: Ok so found out that I have to put the modem/router in bridge mode in order for this to be possible. However, looking up how to do this lead me to a dead end because i need to fill in some fields that i have no idea how to interpret.
VPI:
VCI: These 2 already came with presets. Should I just leave them?
Select DSL Link Type (EoA is for PPPoE, IPoE, and Bridge): Choices of EoA PPPoA and IPoA
Encapsulation Mode: Choices of LLC/SNAP-BRIDGING and VC/MUX
Service Category: UBR without PCR, UBR with PCR, CBR, Non Realtime VBR, Realtime VBR
[code]...
I have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
View 10 Replies View RelatedI'm switching to cable internet service instead of DSL. My Netgear router will not work with my cable modem; but it works like a charm with my DSL modem. Is it a problem with the router setup? Good thing I still have the DSL service.
View 3 Replies View RelatedI have a printer as the sole client on one end of a site-to-site VPN, and the tunnel times out. There is no ability to generate traffic from the printer
Printer end - ASA5505
Other end - Cisco VPN router.
I have Desktop and Laptop connected to a Huawei-make,Model No Smart AX 882, ,via ethernet & USB port. Is it possible to convert the same ADSL wired modem into a wireless modem for my Laptop. the type of hardware to be used (e.g., wireless access point or a wireless router) through my USB port in the wired modem? what is the configuration change I have do in my wired broad band modem?
View 1 Replies View RelatedMy main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
View 4 Replies View RelatedI have a buddy who owns a bar and wants to install a insecure wireless router for his customers downstream from his SBC Global ATT Modem/Wireless Router combo.
-Modem/Router Combo: Actiontec GT724WG
-Downstream Unsecure Wireless Router: D-Link DIR-651
He says has 3 static ips for the modem, and 1 of the network cables coming from the modem directly into the D-Link Router. I first attempted to just plug it into the uplink, and let DCHP do its magic, but I had no luck with that. I could connect to the router but it didn't have internet.
So I restarted the downstream router, and plugged the network cable into the 1st port, and suddenly I had internet on the wireless but it would constantly go up and down, and ping times were extreme erratic.
I have a wireless modem/router combo right now provided to me by Centrylink, its the Q1000. I am trying to hook up a 2nd router to our network to extend range and allow extra ethernet connections points. The new (2nd) Router is a Linksys E1200. I have been told by multiple sources it should be possible to hook the Linksy's router to the modem/router, but I am still not sure how to. All of the directions I have read involve disconnecting the old router (in my case, the Q1000) and then connecting the new router (E1200) in order to configure it. But I am not sure how to do this with out the internet access provided by the old router. how to cascade like this while using a modem/router
View 6 Replies View RelatedI just moved into a new apartment where internet is included with rent and can be accessed via an ethernet port in the wall. I was told I could buy a wireless router and get wireless in my apartment, but my router (Belkin N300) is refusing to set up without a modem. Maybe the lack of modem isn't my problem, but I can't figure out anything else it could be.
View 3 Replies View RelatedActually new internet connection and i want to use an wireless router in my house is it work with out modem
View 1 Replies View RelatedCan we add a router for a wireless modem? Does it make sense? or router is only used for DSL modems in order to connect many computers to NET?
View 1 Replies View Relatedlost password on modum/wireless router
View 2 Replies View RelatedI just had charter install a wireless cable modem into my house and it was put in my study. however, i would now like to get my xbox 360 running as well as the internet for my blue-ray player and tv. So i bought a wireless router.The modem from charter is called: Ubee wireless cable modem (from charter)The wireless router purchases is: Netgear N300 wireless router (wnr2000v3) I am trying to connect them wirelessly. Like I said above, my modem is in the study and the router is about 30 feet away in the living room area.
View 1 Replies View RelatedWhen I attempt to connect my new laptop to it and enter the security key/password, it does not accept it.I was able to connect the computer I had before to the router.How can I connect my new computer?
View 9 Replies View Related