Built in wifi causing blue screen of death. Disabled built in wifi and purchased USB N150 adaptor and blue screen of death has stopped. Download speed are 75% back to normal but surfing is extremely slow using chrome, IE, safari. Ethernet browsing is normal with no bugs or bluescreen.
View 3 RepliesI have many WiSM WLC's running 7.0.116.0. One WLC was rebooted few days ago but there was no crash file and nothing in logs say why this issue happened.There was a power problem at the same time the WLC rebooted (some switches and PE's was rebooted as well) but if it is a power issue why only one WLC inside the WiSM rebooted and the other WLC is still working fine with no reboot?I have 5 WiSM modules connected to the same 6500 box, only one WLC was rebooted which indicates a crash but no crash file registered for it.Is there anyway I can find the reason why that WLC was rebooted?
View 6 Replies View RelatedSo here is what happened, it started two days ago. I use a wifi connection at work, it's an unsecure wifi and I don't know where it comes from. But I am able to get on here at work and do stuff... two days ago I tried and it let me on like normal, but then I couldn't get on websites, it said local access only... so I was like mmm that's odd and the little CD looking thing wasn't there it was just two computers on the bottom right hand corner of the screen. So I restarted after attempting a few times... same problem, finally after a while it let me online but it was very slow and kept kicking me off. When I would try to reconnect sometimes it wouldn't let me and it would give me the option to diagnose the problem or try a new network, I'd move around and finally get on.
I restored back to a day when it was working fine, I did a disc clean up, I used my CCleaner, I defragged my laptop. Still the same problem, my laptop is a Gateway computer running on Windows Vista... so today at first my wifi wouldn't work unless I was standing and holding it... which I found the higher in the air the better it stays connected it seems sometimes.I chatted with gateway and they gave me a few links to download which failed to download once they got to like 30% or so, so I am all out of options I downloaded the wifi link here Download free driver for notebook Gateway ML3109 (Windows 7, XP, Vista) - DriverPack Solutio since that is my laptop
I can't figure out why my Gateway ZX 4300 will not detect any wireless networks. Is there a Wi-FI toggle somewhere?
View 9 Replies View RelatedI'm using Comcast's xfinity gateway and i'm only getting speeds up to 5mbps on my wifi devices (iphone, ipad, apple tv, laptop) while on my desktop that is hardwired, i'm getting 50mbps.
View 1 Replies View RelatedI am trying to set a wireless connection and it says that the Wifi isn't on, which I believe, because I don't even know where the Wifi button is. And the computer didn't come with an owner's manual with a diagram of where and what every button is. Trying to set up PC for bf for Christmas. I am a mac user :P so I have lost my touch with PC's.
View 1 Replies View Relatedhrome threw me a DNS lookup failed. I go into my network settings and I noticed that I had limited connectivity. It would switch between no network access and no internet access every few seconds. After a bit of fiddling around, I got it to connect through assigning myself a static IP. This isn't exactly convenient because I use this computer on multiple networks. When I try to have it on automatic IP, I get no IP address or default gateway when I do an ipconfig /all. It would appear that my router quit assigning my laptop an IP for no reason whatsoever. DHCP is enabled on the router, and all other devices work fine. What could possibly be the problem here? I'm 99% sure it's not an IP conflict either. It's not being MAC filtered because I'm on the thing right now posting this through a static IP. It's not my A/V because it's worked great in the past. Perhaps I should also mention it occasionally says "unidentified network" instead of the SSID
View 8 Replies View RelatedMy gateway vista m-6750 laptop will not connect with wifi. Why is this. I used the operating disk that came sigh the system and nothing. I aso used the two restore CDs that gateway sent me and still no wifi. It won't connect at the free wifi hotspots. I even have At&t wifi service for $19.99 and still no wifi.
View 6 Replies View RelatedI have a Gateway NV59 that I had not used for some time. Recently I started to use it, and I cannot connect to any web pages. I am connected to my wireless network. I have tried all the diagnostic tests I can find on my laptop, and they do not identify the problem. I am running Windows 7 Home Premium. I have Explorer, Safari, and Firefox browsers and non of them will work.
View 7 Replies View RelatedAnyway, a neighbour is letting us share their broadband by way of a wifi connection (on a very long USB lead into the front garden...) but this only works on one PC.The PC is right next to the Orange router (Brightbox) but so far I've failed to do anything like bridge the connections from wifi to ethernet to the router and beyond. Should I persevere with this? I don't understand how this would work in terms of DHCP and routing IP traffic.I'm prepared to buy new kit if necessary (but not much). Most of my equipment is wifi enabled but due to the signal strength of my neighbour's wifi you have to be on the front lawn to get a signal.
View 3 Replies View RelatedHow do I connect my Iphone to my ATT router, Gateway 2 WIRE WIFI?
View 1 Replies View RelatedI have been using a cable modem gateway - Netgear CGD24G from Charter for two years. I just bought Netgear R6300 wifi rounter in order to upgrade the speed and range for my internet. My goal is to upgrade 802.11g to 802.11ac. Is there any special way to setup it up? Or do I need to contact Charter to replace a new gateway?
View 7 Replies View RelatedHave a new Gateway laptop running W8. I have to use Windows diagnostics in Sharing centre to reset the connection although it looks like it is still up.( page cannot be displayed ). Once reset and fixe all is ok until pc goes into sleep mode, then I have to reset again.
View 1 Replies View RelatedI've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...
View 0 Replies View RelatedI picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
'TECHNICAL' SPECS
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
[URL]
config setup
protostack=netkey
klipsdebug=none
[Code]....
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies View Relatedwe do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies View RelatedI have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?
View 1 Replies View RelatedWe have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies View RelatedI have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.
View 2 Replies View RelatedNew hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
I have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc). I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity.
Routing does behave as advertised, where all traffic does go to the main office. However, the 192.168.1.0 subnet in the branch office does not get internet connectivity. I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet. Is there a way to configure the RV082 router to provide NAT for all subnets?
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets? Can the RV082 be used as part of the final solution or are my RV082s a wasted expenditure?
Following is the configuration that I'd implemented, (real IP and IKE keys are bogus).
Gateway To Gateway
Remote Main Office
Add a New Tunnel
Tunnel No. 1 2
Tunnel Name : n1-2122012_n2-1282012 n1-2122012_n2-1282012
Interface : WAN1 WAN1
[code].....
I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway. One location is a static IP Address. The other location is a dynamic IP address.
View 2 Replies View RelatedI have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
Just bought 3 WRVS4400N, I wanted to setup gateway to gateway VPN. I followed the instructions on the WRVS4400N admin guide and VPN does not connect. I also downloaded the VPN setup wizard and that also did get the gateway connected. Everything seems to be correct. Do I have to enable anything else? Firewall setting?
Below is my config.
IPSec VPN Tunnel: Enabled
Tunnel Name: TUN01
Local Security gateway: IP only
WAN1 IP: 192.168.100.1
SUBNET: 255.255.255.0
Local Security type: subnet
LOCAL IP: 10.10.10.1
SUBNET: 255.255.255.0
[code]....
I am trying to set up a gateway to gateway VPN connection between a RV042G (central site) and a RV110W (newest firmware) which is used for presentation purposes on various customer's sites. The RV042G has a static IP. The RV110W has different IPs, depending on where it is used.
Basic VPN settings are clear to me (we have another VPN between two RV042G with static IPs). I set up the VPN connection on the RV042G wth the following settings for "Remote Group Setup":
Remote Security Gateway Type : IP + Domain Name (FQDN) Authentication IP by DNS resolved: mydomain.no-ip.org Domain Name: router12345
The value "router12345" is what I have configured in the RV110W as "Host name" in the network settings.
This configuration does not work so I am obviously doing something wrong. Do I have to use "router12345.mydomain.local" instead if I configured "mydomain.local" as the domain name in the RV110Ws network settings? For my tests the RV110W has a WAN-IP of 192.168.178.100 because it is located behind a DSL-Router. The external IP of this DSL-router is 178.0.x.x. The resolved IP from mydomain.no-ip-org is 192.168.178.100 but when I look in the RV042G log I see the requests coming withg the external IP (178.0.x.x). Is this the problem? The last message I see in the log is "no connection has been authorized with policy=PSK".
Or can I use "IP + Email Address (USER FQDN) Authentication" instead (where can I enter this email address in the RV110W?). Or do I have to use "Dynamic IP"?
Can a router using OSPF propagate that he is a router with default-information originate... at the same time when he got an own gateway of last resort to an IP-adress? If so, how? I can't get it to work.
View 8 Replies View RelatedI try to install a Gateway to Gateway VPN between a RV042G router (LAN1) and a 1721 router (LAN2). The VPN is connected. I can ping the devices from a LAN to the other in the two way.
But otherwise I can't access to the devices of LAN2 from LAN1 like with telnet, HTTP, mstsc, ....
And it is OK to access to the devices of LAN1 from LAN2....
Normally I access to all the resources of LAN2 with the Cisco VPN Client but i try to change it with this router. The firewalls are off on all the computers I look.