Cisco :: 2504 AP - WLC And Access
Jan 16, 2013
So I bought a 2504 AP. I also have some AIR-CAP3602I-A-K9. The WLC web interface sees them in the CDP neighbors. The devices get an ip address but I can't add them as access points. I think if I can do that I can get something simple going.
On the access points I get the stuff below. I didn't set it? At least not the
CISCO-CAPWAP-CONTROLLER
I'll be honest I've never set one of these up and I'm on a steep learning curve!
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:50.167: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.33.0.75,
mask 255.255.255.0, hostname APfc99.47c8.518a(code)
View 6 Replies
ADVERTISEMENT
May 29, 2013
i must configure a secured wireless network with access restriction based on SSID. the equipements are : cisco wlc 2504 (soft 7.3) cisco secure acs aplliance 1121 (soft 5.4) . the users that will connect to the network are regrouped by identity groups, each identity group having it's own SSID. Clearly each group of users must access only one SSID. i followed the procedure below to configure it:
-- creating user identity groups;
-- creating users and assigning them to the groups;
--- creating authorization profiles for each SSID under policy element/ authorization and permission/network access/authorization profiles and putting the Airespace-Wlan-Id(the SSID number) in the radius tab.
--- assigning the authorization profiles to the identity groups under access policies.
after all these config the users can access the network using there userid/password configured. But the problem is Every user can access every SSID, seems like the restriction is so not very well configured.
i found some documentation on this kind of config but the version of ACS used seems older than the one that i use, so menu are very different.
View 8 Replies
View Related
Sep 25, 2012
rececntly we have installed 2504 WLC in of branch office, I can able to log via console but it is not coming over LAN not even showing in CDP, all config seems to be fine in wired side & WLC side & physical connection also fine...LED also green.I am seeing log message in WLC, is this related to License issue
View 2 Replies
View Related
Jun 9, 2013
2504 contrller with 1042N ap's. NPS and group policy (for computers) is setup. Certificates are setup.Logging on as a domain user I can connect to the wireless network but am only getting Internet access. I can not access any domain resources.DHCP is handled by a domain controller. I can ping servers and printers, but cannot access them. Can't map a drive, add a printer or access services on the network.
View 1 Replies
View Related
Apr 4, 2013
I am trying to setup a 2504 Wireless Controller with a few AIR-AP1262N-E-K9 Access Points. But i'm having trouble getting the access points to connect to the controller.The controller and AP's are setup at a local network at one of my customers. They are part of a quite large organization and are therefore connected to some of their other divisions in different contries via MPLS. The DHCP and DNS servers are therefore on a different subnet.I have confirmed that the Access Points do get a correct IP from the DHCP server and that i am able to ping from the controller to the AP. When looking at the controller it does not receive any join requests from the AP's. I have setup a console connection to the controller and 1 AP, so i can view debug information.Most guides mention that you can run different LWAPP commands from the CLI on the AP like show lwapp for example. But i am not able to run any of these LWAPP commands on my AP.
View 8 Replies
View Related
Apr 3, 2012
I have 2 APs, Cisco Aironet 1040, and 2504 WLC.Is it possible to configure guest access (Guest SSID/VLAN and Corporative SSID/VLAN) without dedicated guest WLC in DMZ?
View 4 Replies
View Related
Aug 28, 2012
i have stand alone cisco 1130g ap ,and wlc 2504. wlc 2504 support this ap or not ?
View 3 Replies
View Related
Mar 1, 2013
We have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)
I would like to use LDAP or ACS for authentication purpose.
View 3 Replies
View Related
Feb 24, 2013
I am using Cisco WLC 2504 for provisioning Wireless Connectivity over my Wired Environment. Have deployed 4 Access Points spanning my entire campus as per Customer Requirements. Created 10 SSIDs for Different Networks. Would like to know if there is any possibility of Broadcasting say a particular SSID XYZ on only two or 3 Access Points and keep broadcast disabled on Others.
integrating the authentication on these SSIDs using Active Directory Domain Credentials.
View 5 Replies
View Related
Jun 4, 2012
I have setup guest access on the controller and this is not working at the moment. DHCP server setup on the controller for the Guest users. You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
View 10 Replies
View Related
Jan 23, 2013
We have cisco 2504 controller and 1200 series access point.These are in India and country code is IN.When access point joins the controller , then in wireless>advanced , i see the two country code is already configured these are Sri Lnaka(LK) and Singpore (SG).I have disabled the radios and changed the country code to IN but after doing that Access point is not joining the controller and giving the duplicate error.
Then i have again set the country code to IN,LK and SG.I am able to see the LK and SG but In is not showing in drop down list.
Operationally everything is working fine.
View 3 Replies
View Related
Jul 27, 2012
Question about cisco 2504 wireless controller, is it support cisco 1552E outdoor access point? If NO provide me the correct series/model.
View 9 Replies
View Related
Mar 16, 2013
I have installed/setup a cisco 2504 wireless controller and 3 aironet 1142 access points using the basic config on a windows sbs 2008 domain, the problem is that the clients that are connected to the 2504 aint getting the there ip addr from the AD but from the wireless controller, and there cant reach the clients on wifi from the clients that are connected to lan, is there anyway that i cant change this so that a client on lan can see the client on wlan and vice versa.
View 5 Replies
View Related
Jun 13, 2013
We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?
View 1 Replies
View Related
Jul 12, 2012
I have initially configured 2504 controller with necessary parameters. & we have LAP1131AG access Points. we have connected 2 Nos. of access points in network. we are getting Both AP connected with controller,Whenver i am trying to connect with this wireless network though SSID( currently, open authentication), laptop's not connecting with it. it shown error that " Windows was unable to connect to SSIDname "
View 4 Replies
View Related
Sep 18, 2012
We have a 2504 Wireless Controller and it works great!We currently have 6 Access Points (Aironet 1252) connected.We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.Now, I have been assigned to add another Access Point, but at a remote site.The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.We have plenty of licences on our current Wireless Controller.Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
View 3 Replies
View Related
Mar 2, 2013
Why a 2504 Poe? If it can not be used for AP.
View 10 Replies
View Related
May 11, 2013
I have a wireless controller that works perfect but because we have some new access-points 1602i that is only supported bij software version 7.4.100.0. So I need to upgrade the controller because I now have version 7.0.116.0. I have read in release notes of version 7.4.100.0 that I first need to upgrade to 7.0.240.0 to avoid losing those VLAN settings.
Note If you have VLAN support and VLAN mappings defined on H-REAP access points and are currently using a 7.0.x controller software release that is prior to 7.0.240.0, we recommend that you upgrade to the 7.0.240.0 release and then upgrade to 7.4.100.0 to avoid losing those VLAN settings.
But I also read something about Field Upgrade Software. If you are using a Cisco 2500 Series controller and you intend to use the Application Visibility and Control (AVC) and Net Flow protocol features, you must install Wireless LAN Controller Field Upgrade Software for Release 1.8.0.0-FUS. This is not required if you are using other controller hardware models. For more information, see [URL] .....
Here is the system information of my controller:
Manufacturer's Name.............................. Cisco Systems Inc.Product Name..................................... Cisco Controller Product Version.................................. 7.0.116.0Bootloader Version............................... 1.0.16Field Recovery Image Version..................... 1.0.0Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... WIFI-WLC-01System Location.................................. System
[Code] ....
I was thinking of the following steps:
1. Backup the current config
2. Upgrade to version 7.0.240.0
3. Test and backup the config
4. Upgrade to version 7.4.100.0
5. Test and backup the config
6. Upgrade Field Upgrade Software 1.8.0.0
7. Test
View 3 Replies
View Related
May 24, 2012
I'm having some weird issues where I cannot ping from the WLC to the IAS RADIUS server. All of my clients cannot connect, but from the switch, router, RADIUS server, and hard wired clients, I can ping to the WLC and RADIUS server. The only thing that cannot ping the RADIUS server is the WLC itself. Nothing in the FW is blocking connectivity. [code]
View 11 Replies
View Related
Jan 22, 2013
I'm planning to upgrade our WLC 2504 from 7.2.111.3 to 7.4.100.0 but the cisco site says "WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time" Is it something about NCS? we have only 1 cisco WLC 2504 and 6 1142APs.. Also let me know is it possible to go directly from 7.2 to 7.4 ?
View 8 Replies
View Related
Nov 28, 2012
what is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
View 8 Replies
View Related
Aug 29, 2012
I've problem with a WLC 2504. Some Clients like phones and Thin Clients get an IP 0.0.0.0.Software Version is 7.0.235.0. Test with a Laptop seams to be OK. Some printers also got an 0.0.0.0.Around 30% are not OK. also had the log: Impersonation of AP with Base Radio MAC 00:yy:yy:yy:yy:yyusing source address of 00:xx:xx:xx:xx:xx has been detected by the AP with MAC Address: 00:yy:yy:yy:yy:yy on its 802.11b/g radio whose slot ID is 0 The problem is, I cannot go to 7.2 version because I have 2 x AP 1231 and 2 x 1242 AP's.1231 AP's are not anymore supported in 7.2 Version.
View 14 Replies
View Related
Mar 29, 2012
i am trying to get ad authentication working on a WLC 2504, can I use the LDAP server configuration for authentication?
View 1 Replies
View Related
Aug 15, 2012
I have two WLC 2504 controllers. These controllers are for two different buildings. But they share a VLAN, and network address range. How can I control the access points to the register selected only at a specific controller.
Example:
AP 1 -> WLC 1
AP 2 -> WLC 2
AP 3 -> WLC 1
Since the buildings also broadcast in different SSID. The two controllers are in a mobility group.
View 4 Replies
View Related
Jul 5, 2012
I'm having issue to setup authentication with our external Radius server so I'm thinking whether the 2504 has inbuilt feature which I can configure as a Radius server? if so are there any guide for configuration?
View 1 Replies
View Related
Jul 12, 2012
If we update our ios on WLC do we have to add the certificate for AP's again or we don't need to do that.
View 4 Replies
View Related
May 22, 2013
I have an allready configured WLC 2504 running in the network. Every LAP i add to the network joins imidiatly to the Controller. But not the AP1121G AP. It fails the Handshake everytime and the Controller shows me an failmessage at the statistics in the GUI. [code]
View 3 Replies
View Related
Mar 13, 2013
Some time ago I updated a WLC, model 2504, from version 7.3 to 7.4.100.0. I also update the FUS (Field Upgrade Software) to the latest release, 1.8.0.0. Now I need to downgrade the WLC back to 7.3 version.
My doubt is: Can I just take the normal processes and downgrade the WLC back to 7.3, even with the FUS in version 1.8.0.0?
View 5 Replies
View Related
May 17, 2011
I've read some conflicting things on the new 2504 WLC's. Some things indicate all 4 ports are fully useable, while others indicate perhaps only 1 or 2. I think I've read in product documentation that it support a max of two ap-manager interfaces. Does, for sure, all 4 ports are useable? I'm thinking of the following configuration:
Port 1: management interface and first ap-manager interface
Port 2: second ap-manager interface
Port 3: first dynamic/client interface
Port 4: second dynamic/client interface
I'm planning on deploying my ap's in h-reap mode with a max of 25 ap's per 2504. Since I'm using h-reap, bandwidth shouldn't be much of an issue so I'm also considering trimming it down to using just two physical ports as follows so I can take up fewer gig switchports which are scarce at many of my locations:
Port 1: management interface and first ap-manager interface
Port 2: first and second dynamic/client interface
I've always deployed 4400's and 5508's with LAG so I haven't had to think about this much until now.
View 4 Replies
View Related
Jun 10, 2013
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
View 15 Replies
View Related
Dec 21, 2011
Can a 2504 wlc use a vlan ids of 190X? I have found that it supports 512 vlans but I have not found any restrictions in the id used.Vlan id 190X is distributed by the isp (they have the ASAs in their central site) so if it is not supported I must prepare a vlan transfer between switches.
View 4 Replies
View Related
Jul 29, 2012
Is it possible to use a 2504 wifi controller to manage compatible AP's across different subnets ?
View 2 Replies
View Related
Oct 16, 2011
I have deployed a 2504 controller with EAP-TLS however we are receiving the following errors where it appears the EAP response timeout from the client is expiring and not receiving a reply, this is happening with all clients.
We have three SSIDs one with EAP-FAST working perfectly, and a third with WPA2-AES itis only this where we are seeing the response appear to expire. Running code 7.0.116.0 on a WLC2504. RADIUS shared secrets all ok.
*Dot1x_NW_MsgTask_5: Oct 17 11:16:16.207: 00:19:7e:c3:ab:35 Sending EAP Request from AAA to mobile 00:19:7e:c3:ab:35 (EAP Id 224) *osapiBsnTimer: Oct 17 11:16:46.036: 00:19:7e:c3:ab:35 802.1x 'timeoutEvt' Timer expired for station 00:19:7e:c3:ab:35 and for message = M0 *dot1xMsgTask: Oct 17 11:16:46.037: 00:19:7e:c3:ab:35 Retransmit 1 of EAP-Request (length 14) for mobile 00:19:7e:c3:ab:35 *osapiBsnTimer: Oct 17 11:17:16.036:
[Code]....
View 4 Replies
View Related
