Cisco :: 2960 - LMS 4.2.2 SNMPV3 Wrong Privacy Algorithm

Oct 24, 2012

we use LMS 4.2.2 to manage our Cisco devices. At the moment all devices are managed with snmpv2. I´ve picked one Catalyst 2960-24TT-L Version 12.2(25)SEE3 and configured snmpv3
 
Here´s the output of show snmp user:
 
User name: ciscoworks
Engine ID: 8000000903000022BD29EF40
storage-type: nonvolatile        active
Authentication Protocol: MD5
Privacy Protocol: DES
Group-name: LMS
 
Now, in LMS under Admin->Network->Device Credentials Settings-> i created a new credential set "snmpv3" with the correct user/password and following settings: AuthPriv (enabled) Auth Algorithm MD5 Privacy Algorithm DES (because the 2960 12.2(25)SEE3 doesn´t support any other alorithm).
 
I´ve edited the credentials and assigned the new set to that device. Now to test the snmpv3 credentials i´ve started an Device credential verification job an chose snmpv3 only. But every time the job failes with the error
 
Wrong Privacy Algorithm.

View 1 Replies


ADVERTISEMENT

Cisco :: SNMPv3 On 2960-S Switch To NCS

Jan 18, 2012

how to set up SNMPv3 on a Cisco Catalyst 2960-S switch in order to manage it with Cisco Prime NCS?

View 1 Replies View Related

Cisco Switching/Routing :: 2960 / 2621 - IP From Wrong VLAN Being Handed Out

Dec 29, 2011

Setup is like this:  Poly com IP phones -> Cisco 2960 switches -> Cisco 2621XM router running 12.28(r).  A Windows 2003 server running on HP Proliant DL380 G4 with the correct DHCP scope is configured for the IP phones, also sitting on a Cisco 2960 switch.

A typical port config on the 2960 is:
interface FastEthernet0/1
switchport mode access
switchport voice vlan 60
mls qos trust cos
auto qos voip trust
spanning-tree portfast
spanning-tree bpduguard enable

Relevant section of the config on the 2621XM router:
interface FastEthernet0/0
no ip address
no ip redirects
no ip proxy-arp
ip pim sparse-dense-mode
[Code] .......

This used to work on a Windows 2000 server which sat on different piece of hardware, but stopped immediately after the migration to Windows 2003 server was done.  There was no change on the router or switches prior to or after the server migration.  I see DHCP server log on the 2003 server giving DHCP NACK because the phones are apparently asking for IP's in the data VLAN.

View 14 Replies View Related

Cisco Switching/Routing :: 2960 / Recovering Switch With Wrong BAUD Rate?

Oct 20, 2012

it seems that i made a mistake when typing the BAUD rate of a 2960-Switch in rommon.I can't start the switch now, because there is no image on it (because I deleted it before) and the baud-rate has wrong settings. When connecting via console cable i can't see anything (except some strange hieroglyphics) when starting. I tried all the speeds in teraterm... without success.what can i do, to recover the switch back?

View 8 Replies View Related

Balancing VPN Use And Privacy?

Feb 27, 2011

We have business and private virtual hard-drives on the one networked hard-drive. We wish to arrange that VPN visitors can only see the business virtual drives. Do we create two networks or two domains for instance? We have set up logmein succesfully but it does not provide the privacy we need.

View 3 Replies View Related

Cisco :: Encryption Algorithm In ST 40 / ASR 5000?

Mar 14, 2011

Due to  network security audit we are interesded in encryption algorithm used  for authentication of administrator and operators in Starent Networks  ST40 Intelligent Mobile Gateway. To be more clearly, we need to know what type of hash is used for password storing when "showsecrets" command is omitted.

View 2 Replies View Related

How To Get Complete Privacy On One Internet Line

Dec 11, 2011

We have Comcast cable (I believe) and it comes into a modem. The modem has a line out to an ethernet switch. Coming into the E switch is a line from the Upstairs router (Realtek PCIe GBE).I want MY computer to be completely private from the rest of the family, and be invisible if someone were looking. (I'm mom and I keep my frustration journal on my Microsoft Word). I don't want to use wireless.

So, I bought a Belkin N150 and put it between my computer and the switch, and the internet didn't work at all. However, if I use a line that comes from the Realtek router, it works. I am SO confused! (I found out that if you are hooked to the same router as the others in the house, they just have to be smart enough to configure that router and they can see everything you do on your computer!)

View 6 Replies View Related

Cisco Firewall ::ASA 5550 - SHA1 Signature Algorithm On FWSM

Mar 11, 2013

I would like to ask whether SHA1 signature algorithm is available for FWSM. We use FWSM code version 3.2(22) in our production network where only MD5 signature algorithm is available. There is a need to upgrade to stronger algorithm SHA1. From my experience I know that this is possible on ASA firewalls running on 8.4. codes. Certificates generated on code 8.4. automatically use SHA1 with RSA Encryption.
 
Is it possible to have Signature algorithm SHA1 on FWSM? If so, in which code version?
 
hba-pf-a# sh crypto ca cert
Certificate
Status: Available
Certificate Serial Number: caf44050
Certificate Usage: General Purpose
Public Key Type: RSA (2048 bits)
[Code] .....

View 2 Replies View Related

Recommended Settings PCIe GBE Family Controller For Privacy?

Sep 25, 2012

Just a general concern for privacy, on my NIC card and gateway stock from HP, as well as performance...where should we draw the line and consider ourselves safe? Being disabled and pretty much not able to work no longer with a life threatning illness, and not much in my bank account, I have not much to worry about this. However I dont want my typical neighborhood kid hacking on my connection either, it tends to slow down your bandwidth.

View 2 Replies View Related

Wireless :: Selective Encryption Algorithm In Wired Network?

Sep 22, 2011

if there is a wireless adhoc network and i want to provide the security to the data which i want to transmitt over this network but i dont want to encrypt the whole data but to apply encryption in a part of data which conatins the important information.

View 1 Replies View Related

Security / Firewalls :: Best Email Service For Privacy / Daily Usage?

Jun 30, 2011

What is the best email service that puts a high priority on privacy yet is still easy to use on a daily basis?

View 2 Replies View Related

Cisco Firewall :: ASA5520 HTTPS SSL Certificate Signed Using Weak Hashing Algorithm

Oct 18, 2011

I am support one client for,  whom falls under Security  scans mandatory for new implementation of ASA 5520 device.  The client uses Nessus Scan and  the test results are attached.The Nessus scanner hit on 1 Medium vulnerabilities.

View 2 Replies View Related

Linksys Wireless Router :: WRT320N Privacy From Other Network Computer Users?

Jun 14, 2012

I am grudgingly forced to allow certain people to use my wireless router connection. I just found out that these users are able to see a display of all the devices and computers attached to the router and network. This isn't a priviledge I'd like them to have. I'd like them to only be allowed to surf the internet - and leave it at that. I use WEP with a 26 digit code and each user has been given the code.)

View 5 Replies View Related

Cisco Switching/Routing :: 4500E - Changing Default Etherchannel Load Balancing Algorithm

Mar 25, 2012

Will there be some pause in traffic on formed ether channel interfaces (4500E switch), when i will change the default ether channel load balancing method to src-dst-port (or any other non-default method)?

View 1 Replies View Related

Cisco :: Configure SNMPv3 On 2960G (12.2.55)?

Sep 30, 2012

I am trying to configure SNMPv3 on a 2960G (12.2.(55)) 
 
snmp-server view v3view interfaces included
snmp-server view v3view internet included
snmp-server view v3view chassis included
snmp-server view v3view system included
snmp-server group v3group v3 priv read v3viewwrite v3view notify v3view
snmp-s user v3user v3group v3 auth md5 v3secret priv aes 128 v3secret
 
Interestingly enough when I 'sh conf | i snmp' the user command isnt there, however it shows it under 'sh snmp user'.  Using Solarwinds Eng Toolset to attempt to just pull interfaces and it keeps kicking back with creds failing.

View 4 Replies View Related

Cisco :: LMS 4.0.1 User Tracking With SNMPv3

Dec 6, 2011

I have an interesting problem at one of my customers. They are using LMS 4.0.1, but they have a problem with user tracking with SNMPv3. They using a very simple SNMP configuration, wich is the following: [code]
 
Now they have UT working well for their Ctalyst 4500 switches, and the half of the 6500s (They have 2950 switches as well, but for those UT with SNMPv3 is unsupported). So the problem is the following: they have 12 6500 switches, with the same IOS version (10 pieces of WS-C6506-E + SUP720-3B IOS: 12. 2 (18) SXF17 (IP Services), 2 pieces of WS-C6506 + SUP720-BASE IOS: 12.2(18)SXF17 (IP Services)). They have identical SNMP configuration on both devices. Based on the logs from LMS it seems that on the problematic switches for some reason LMS identifies the switchports as routed: [code]

View 5 Replies View Related

Cisco :: AES 256 - Prime Infrastructure 1.2 With SNMPv3

Apr 2, 2013

I am trying to add a router on Cisco Prime Infrastructure 1.2 using snmpv3 (authpriv, sha & aes256). When i go to device work center and add a device, i cannot find the AES-256 in the privacy options. Only None, DES, and AES-128 are available.

View 2 Replies View Related

Cisco WAN :: 1900 Router Supports SNMPV3?

Feb 8, 2013

We are using Cisco 1941 Router as CPE where we wanted to trap CPU, Memory & ISYSTEM MIB. The same we are achiveing using SNMPV2 but when we tried using SNMPV3, there is no response for these MIBs.
 
We tried to configure SNMPV3 using below Link but still there was issue. There was response fr [URL]
 
Wanetd to know SNMPV3 MIB are supported for Cisco 1941 Router IOS Code universalk 15.2(3)T1 & Data License. When we tried using Cisco IOS MIB Locator, we are not able to see any MIB for SNMPV3. whats is that mean. Does this Platform + IOS Support SNMPV3 or not.

Below is the Snapshot from Cisco IOS MIB Locator for said image.

[Code]......

View 3 Replies View Related

Cisco :: LMS4.1 SNMPV3 Configuration Template Required

Apr 6, 2013

Who can give me a SNMPv3 configuration template.I tried many times has been a problem

View 5 Replies View Related

Cisco Firewall :: 5510 / Setup Snmpv3 With Active Failover?

Apr 1, 2012

What I am attempting to do is setup snmpv3 on two failover 5510's .The problem I am running into, the snmp management software rejects one of the devices as it sees it as having a duplicate engine ID since the two devices share the same config.  Would like to know how this would work in an active/active setup being able to poll both devices.

View 2 Replies View Related

Cisco Switching/Routing :: NEXUS 5500 NX-OS Configuring SNMPv3

Jan 16, 2012

IOS we used for limiting access for a group we used configuration of snmp-server views like following
 
snmp-server group backupgroup v3 priv read backupview write backupview access 20 snmp-server view backupview ccCopyTable included could not find out how to achive this config in NX-OS on Nexus5500

View 2 Replies View Related

Cisco :: LMS3.2 Snmpv3 Error Performing SNMP Operation

Jun 1, 2010

i've the following problem. Check device credential verification job shows "Error performing SNMP operation" for a cisco 3750 configured with snmpv3.On the switch i can see that the lms can access the switch via snmpv3. Also cisco view works fine. Bug CSCsm89609 describe the problem but it should be fixed in RME 4.3. We are running 4.3.1.

View 9 Replies View Related

Cisco Switching/Routing :: Setup SNMPv3 On Nexus 5548?

Sep 18, 2012

I'm trying to setup SNMPv3 on a Nexus 5548. We are using SNMPv3 on 3750's without any issue, but haveing issues getting it setup on the Nexus.I have been using the following link for the setup following it line by line. [URL]The part that I'm having issues with is when I try to enforce SNMP message encryption on a per user basis. When I issue snmp-server user (username) enforcePriv, I get warning: unable to update CLI users database. reason: role does not exist grounp not found.

View 1 Replies View Related

Cisco :: 6506 Switch - SNMPv3 User Without Group Setting Showing

Sep 4, 2012

Why is it that when SNMPv3 user "TestV3-User" was added to my SNMPv3 implementation on my 6506 switch, the group/MD5/Emcryption settings are missing for this user (See "sh snmp user" output)???
 
router#sh snmp user
User name: TestV3-User
Engine ID: 80000009030000249706EFC0
storage-type: nonvolatile        active access-list: test

[Code]....

View 3 Replies View Related

Cisco Switching/Routing :: Add 2960 To Stack Of 4 X 2960 Switches

Feb 7, 2012

I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.

View 12 Replies View Related

Cisco Switching/Routing :: 2960-S To 2960-LST Configuration Over Fiber?

Feb 11, 2013

I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber.  The link is up on the LST but will not come up on the -S.  What command should I use to bring up this link?  I have tried no shut from the (Config-if)# prompt.         

View 3 Replies View Related

Cisco :: Phone Keeps Registering With Wrong CME?

Jan 6, 2011

I have a CME on the other end of my MPLS network. When troubleshooting phone issues i setup a phone on the CME system in question and point its TFTP server to the address of the CME router. Now, i need to point this phone to another CME but it keeps registering with the previous one no matter what i do (the TFTP server is pointed to the new CME). I have tried turning off the auto register, and i have deleted the ephone and its mac address all together but it always registers with the wrong CME.

The phone is a 7962 with a 7914 expansion module.

View 10 Replies View Related

Cisco VPN :: PIX 525 Routing To Wrong Interface?

May 2, 2011

PIX 525 6.3(4)120
 
I am trying to allow clients coming in from my "DMZ6"  interface with source IPs from the subnet 192.168.2.0 /24 to ping and  access hosts on my "DMZ1" interface with destination IPs in the subnet  10.5.11.0 /24. I think I have the associated static NATs and the ACLs  set up to allow this to happen. What I have noticed from syslog messages  is that the PIX is trying to build the TCP connection to the "Inside"  interface, rather than to DMZ1. Even though the destination host  (10.5.11.12) is directly connected on DMZ1, the PIX is still trying to  send the traffic to the "Inside" instead. I tried adding a host route to  force 10.5.11.12 /32 pointing to DMZ1 and the PIX still tries to send  the packets Inside. This only seems to happen when I try to go from DMZ6  to DMZ1. If I try to access hosts located in DMZ3 for example, which is  also a directly connected interface on the PIX, it appropriately builds  the connection to DMZ3. Here are the pertinent rules. Why would the PIX want to build the connection to the Inside,  even though it knows that the destination host IP is directly connected  to DMZ1?
 
ip address DMZ1 10.5.11.1 255.255.255.0
ip address DMZ6 10.5.16.1 255.255.255.0
ip address inside 10.5.18.17 255.255.255.240

[Code].....

View 2 Replies View Related

Assign Wrong Mac Address?

Jul 16, 2011

I have a 2003 server that is doing something wrong. When I show the mac address table I can see that the server is assigning a bad mac address to several IPS. The server assign a non-existent mac address to some IPS for this reason the server stobut I would like to solve the problem

- I ran my antivirus an no virus was found.

- I updated the network driver.

View 4 Replies View Related

Cisco :: Wrong IOS On A Switch Service Module?

Mar 11, 2013

I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)

View 4 Replies View Related

Cisco Router Giving Out Wrong Address?

Jun 21, 2011

i have a cisco router that has dhcp configured, the router ip address is 10.10.10.***. all computer that attached to the router are using static ip and works fine but when i am connecting my laptop using wireless in gets an 192.168.1.*** address.

View 17 Replies View Related

Cisco Wireless :: 1142N AP Upgrade Gone Really Wrong

Jan 24, 2012

I have run into a major issue with an autonomous Cisco 1142AP. We were in the midst of a firmware upgrade when something went wrong and caused the AP to reboot in an error mode. Basically the unit was flashing Blue, amber, red. We unmounted the unit from the wall, connected to the console, and it would now only flash red over and over. We pulled out the cisco guides and performed a factory reset on the unit. This still does not work. and the contents of our flash directory is empty. All we get is a ROMMON AP prompt on the unit. If I issue a set command, I can see the default settings for IP, netmask, etc.
 
I cannot access the unit via the network, even after setting IP info and matching it up to my laptop. Since I have no network connectivity, I can't TFTP a new IOS file to the unit. I am stumped. How to get the config as if it was out of the box, or an alternate way to TFTP to the unit? [code]Notice the lines in red, I must have typed someting incorrectly.Now once the unit boots after being reset, I cannot even type in the CLI. Someting majorly screwed up here. Can the bootstrap be reinitialized?

View 3 Replies View Related

Cisco :: Updated AP1121 With Wrong Software

Jun 11, 2013

I updated an AP1121 accidentally with the LWAPP version of an AP1130ag.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved