We have a LMS 4.2 installed. And I see the tftp port is open on it. however, every time, i tried to "copy running tftp" to the LMS from a switch, it says the Trying to connect to tftp server Connection to Server Established.TFTP put operation failed:Access violation
i seem not be able to find where to configure the tftp server.
I am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies View RelatedI am trying to implement a small VoIP LAN (you can see the lan in attachments)for a personal project. I am using:
- 2 x XP (on which i installed Cisco IP Communicator 7.0.3.0)
- 1 x Ubuntu (running GNS3 with a c3600 Router)
The problem is that the phone which is not in the same LAN with the tftp server cannot register.
1) Can a phone register to a tftp server from another LAN ?
2) If the answer for 1) is yes, what am i doing wrong (you can see the details in the attachments)? I mention that the ping works well anywhere in the LAN.
I have a questions on an Ip phone when getting the firmware from the TFTP server (e.g. CME) after bootup,- After the registration with CME, the IP phone will getting an auto config file which is the Default.xml file. - The CME will acts a a TFTP server which contains all the IP phone's firmware for different models like 7970 and 7640 in different directories.- The CME have configured with the directory path for all the IP phone when the IP phone come to TFTP and acquired the firmware.Let say I have a phone registered is 7970 and what is the mechanism that governs that my 7970 is not downloading the wrong firmware from the TFTP? Let say it might wrongly downloaded the 7640 firmware? Who take care of this? The phone itself? or the CME will tell the IP phone to take only the 7970 firmware via the Default.xml file?
View 1 Replies View RelatedIs there a way to backup the configuration file to a tftp server? I've tried "copy start tftp" and copy run tftp". No luck, I get an error message.
View 1 Replies View Relatedow to backup Cisco ASA-5510 from a Linux server via TFTP?I do know how to backup a switch or a router. Basically creating an access list such as:
access-list 55 remark PERMIT hosts requesting TFTP access
access-list 55 permit host 172.16.0.27
and allowing access to
tftp-server nvram:startup-config 55
all this inside the router or the switch. From the Linux box just running a simple command such as:
tftp 172.16.0.3 -c get startup-config newbackup.conf
where 172.16.0.3 is the IP address of the switch and newbackup.conf is the name of the config file stored on the Linux machine.So, how do I do that with an ASA box? how to backup ASA from inside it.
I need to do one Catalyst 5500 as a TFTP server.Can I do it?Is the catalyst available to be a tftp server?
View 4 Replies View RelatedHow do i go about setting up a TFTP server from laptop to Cisco ws-C3750 48P Switch, I need to pull the image off the switch and place it on an other switch that has a corrupt image, The switch which is corrupted is the same as above Cisco ws-C3750 48P.
View 1 Replies View RelatedI am trying to convert two Aironet 1141n access points to autonomous stand-alone units. I have connected the console cable and I can see the unit giving information in the console window, but I cannot type any commands. When I try to get the unit to upload the c1140-k9w7-tar.default file by holding the mode button in for 20-30 seconds, it shows it is examining the file, and then states that the connection to the tftp server has timed out. My windows firewall is off, the interface is configured as 10.0.0.2 255.255.255.0 and the tftp server is showing that.
View 15 Replies View RelatedI have been trying to get a PIX 501 firewall reset and have been having the hardest time. Im a student and this is my first experience with a firewall. I have been going through the steps here URL,I cant seem to connect to the tftp server, I have several nic's on my computer and tried them both and even plugged the firewall to the router and tried to use the gateway to connect but it doesn't seem to want to even ping for me.
View 4 Replies View RelatedI have been looking at grading the IOS version on our 6509-E however there is not enough space on disk:0 to upgrade to the version I need to install. The question I would like to ask is - is it possible to boot the IOS from a TFTP server? If this is possible what configuration do I need on the 6509 to enable this. How does the 6509 know about the TFTP server as an IOS is not installed and therefore it will not have a network configuration
View 2 Replies View RelatedI have a Cisco 831 router (c831-k9o3y6-mz.124-5c.bin) that cannot backup the config to a local tftp server. I have seen this behavior on a few different Cisco devices over the years and have never found a solution. The connection is made to the tftp server (in this case tftpd but similar behavior on any tftp server) and a blank file is created on the target machine file system, but the data is never transferred.
The router shows %Error opening tftp://192.168.0.2/router-confg (Timed out) [Failed]
The tftpd log shows 5 repeated attempts at the file write.
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:40.922]
Write request for file <router-confg>. Mode octet [25/05 11:56:40.922]
Using local port 61607 [25/05 11:56:40.922]
<router-confg>: rcvd 0 blk, 0 bytes in 3 s. 0 blk resent [25/05 11:56:43.922]
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:43.923]
[Code]...
This is also stopping me upgrading the image on the router as I cannot transfer in the other direction either.
I wonder if dir825 with ddwrt firmware are able to set up additional tftp server? I try to serve dir825 both as tftp server and dhcp server to allow remote client to have pxe booting from it. ( the booting image file would be located in external HD attatched to dir825's usb port )
View 1 Replies View RelatedI need to transfer a config from a TFTP Server to a 4507 and a 6513. When I transfer the config to both those switches, does it require a reboot?
View 5 Replies View RelatedI am trying to copy IOS from my TFTP server which is on my laptop to cisco 2960 switch
I am able to ping to switch from my laptop, connectivity is fine, tftp server is running
Current Image on Switch --> C2960-LANBASE-MZ.122-25.SEE3.bin --> trying to upgrade to --> c2960-lanbasek9-mz.122-53.SE2
I am getting below error when trying to upgarde IOS:
2960-SW#copy tftp: flash:
Address or name of remote host []? 10.1.x.x
Source filename []? c2960-lanbasek9-mz.122-53.SE2
[Code].....
how can i take backup of startup config to tftp server through tftpd server.I am using 4506e switch
View 2 Replies View RelatedRecently had an external security scan done on my DIR 655 and scan results are stating I have an accessible TFTP Server running. i've been through all the settings, and even upgraded to the latest firmware. Yet security scans are telling me I've got a TFTP Server running. Why would one be showing on the external interface, and how can I stop it?
View 7 Replies View RelatedI got a Monoprice Networking USB 2.0 Server and it doesn't appear to be working. I hooked it to my router (Linksys E1000) and I have my usb printer hooked to the device. The driver for the printer is installed for the server. When I go to print something I get a popup saying "checking status of printer," it hangs for a minute, and then says "printer not responding." There's no indication of the server or the printer in my network. How do I get this thing working
View 2 Replies View RelatedI have installed VM ware v Sphere Enterprise Plus 5.0.0 and created a VM using an OVA file with LMS 4.1 running in Linux. It was working good since 3 weeks ago and I was adding snmp server configuration in all my devices (routers/switches) and suddenly one day DCR Server process stop working. I was trying the following actions:
1.- dmgtd stop -> to stop daemons
2.- dmgtd start -> to start again the daemons
And the DCR Server does n´t start up automatic.
Then I try this:
1.- pdexe DCR Server
And show this message:
[CPLMSCOL01/root-ade ~]# pd exec DCR Server
ERROR:Get reply from server failed:
and don´t start up the DCR Server.
I'm having trouble TFTPing a configuration from my 851 Router to my computer through a IPsec VPN tunnel that this router is connected though. I am able to telnet and ping all devices on the far-end with no problem. I can TFTP a config from a switch behind this router, no problem. I am guessing this problem is related to an ACL on the router. I am also having trouble connecting to this router using the Cisco Config Professional. Discovery will fail, with connection could not be established or HTTP service is not enabled. I have enabled HTTP service. The CCP works fine when I am on the router's subnet.
View 3 Replies View Relatedi am in the process of setting up a business and we have brought the server from a previous company and added a 5 port switch to it. But after setting up wireless internet yesterday my bosses internet will not work when the server is plugged into his laptop. However it works fine on mine.
View 13 Replies View RelatedOn Windows XP, my integrated NIC stops working after hosting a server. The server starts fine, ports are forwarded, firewall is down, modem is fine, but when I receive a connection, it shows they have made a connection, but then they drop, as do I. I can't browse or ping anywhere. I have to physically disconnect, then reconnect the ethernet cable to the port, or restart the computer. Upon ipconfig, the adapter is set with the Windows default ip (169.x.x.x) and cannot be /release'd or /renew'd.
View 10 Replies View RelatedI've got a fully working 877w that I'm trying to get to boot from tftp, but I just can't seem to get that going.I have a tftp server running and can copy images back and forth without any trouble.I have this in my config:boot-start-markerboot system tftp c870-advipservicesk9-mz.124-24.T2.bin 192.168.1.200boot-end-markerDuring the boot process I get an error message that says there is a missing or illegal ip but I really don't see how that can be as my tftp server is 192.168.1.200 just like my config says.
View 16 Replies View RelatedWhen pusing configs using tftp, for example using Ciscoworks, does it push out an entire new config or does it just edit specific changes?
View 1 Replies View RelatedASR 1004, has a image, which is on the harddrive, not bootflash and we have no boot commands in the configuration…We are running the ROMMON version ‘15_01rs’ The ASR boots into Rommon, as it cannot find a image (as expected), as the configuration has no boot commands.Trying to TFTP or getting an IOS back into bootflash is proving problematic.Follow all TFTP commands..
rommon 1 > IP_ADDRESS=10.1.1.1
rommon 2 > IP_SUBNET_MASK=255.255.255.0
rommon 3 > DEFAULT_GATEWAY=10.1.1.1
rommon 4 > TFTP_SERVER=10.1.1.2
rommon 5 > TFTP_FILE=asr1000rp1-adventerprisek9.03.01.01.S.150-1.S1.bin
[code]....
I need Cisco router 2800 series boot ios image from network(tftp), when flash is corrupted or router doesn't see it, so it is impossible ? Command, i used boot system tftp: ios.bin but this does not work.
View 9 Replies View RelatedI can't get connectivity from laptop to AP using cross over or straight through cable to do a tftp transfer from tftp server on laptop to ap.
I held the mode button on ap and powered on to get to rommon. The ap has no ios so it goes to rommon anyway. ap light is blinking red.
ap: set
DEFAULT_ROUTER=10.0.0.1
IP_ADDR=10.0.0.1
NETMASK=255.255.255.224
[Code].....
I install virutal machine "VMWare Workstation7" on windows 7, i am mcitp student for practice i am using windows server 2008 on VMWare, but i can't assign static ip whenever i assign ip it show no access to the internet?
View 3 Replies View RelatedI just finished setting up VPN server on my Windows 2008 server. I defined the users that should be able to access the server and applied permissions. When I test the VPN connection on the LAN (loacally) I have no trouble connecting and establishing VPN connection.However when I tried externally it's a different story. I am not able to connect and always get the same not so clear 800 error ...The remote connection was not made because attempted VPN tunnel failed. I have Zyxel router for my internet connection and I have forwarded all relevant ports I think for the protocols I am using. Port such as 1723,1701,1702,47,50,51,500,1293,443,4500 are forwarded to the server.I am able to telnet to the server on port such as 1723.
View 1 Replies View RelatedWe have 3 internet links from different providers connected to configured WAN 1,2,3 in RV016. A remote client needs to connect to a internal VPN Server behind RV016, so we use one-to-one NAT to publish the internal server ip to a Valid IP from WAN3 and setup protocol binding in Multi wan to all trafic (TCP and UDP) from the internal VPN address exits with WAN3.
So, the remote client tries to connect to VPN using this ip Address from WAN3 and sometimes work and sometimes not. It's clear to us that the problem lies in the response from RV016 not coming always from WAN3, because if we disconnect the two other links (WAN1 and 2) Its works flawless.
My mail server is not in my network, it's over internet elsewhere.After installing the ASA 5510, i can not get my mails any more.
View 7 Replies View Relatedsetup a DHCP server on a WLC 2504. I'll try to resume my configuration:
I have 2 networks: inside users (vlan 1) and external users (vlan)
My controller uses the port 1 to connect to the switch, which has a trunk with WLC.
I have two routers, one using vlan 1 (192.168.3.0/24) and one using vlan 10 (200.X.X.X). All ports to these routers are access ports on their respective vlans.
I have 2 SSID, one for inside, other to outside. Inside is working very well.
To the outside I created a DHCP escope and already set the IP of the management interface 192.168.3.119.
Managemente interface (vlan 1 inside): 192.168.3.119/24
Outside interface (vlan 10): 200.X.X.195 - Default gateway 200.X.X.X.193
I alredy checked the DHCP Proxy in Advanced option.
See the output of the debug client:
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
[Code].....
I possess a RV220W (firmware 1.0.3.5) but I can't seem to work with the PPTP server on one VLAN only.
My default VLAN is in 192.168.1.1/24. I created a VLAN ID 10 in 192.168.50.1/24 inter-vlan routing : disabled and Device Management : disabled. (Menu Networking > LAN > VLAN Membership and Multiple VLAN Subnets).
Then I configured a PPTP server on the IP range 192.168.50.200 to 192.168.50.210.
To finish I created my user. (Menu VPN > IPSEC > VPN Users).
The PPTP tunnel is working, but on all my local network and not only the VLAN ID 10.