I'm finding information about the RFC 2544 latency of the IE3000 device.Does it exist a document containg latency value measured in relation to packet dimension?
View 0 RepliesI'm trying to spec out some switches in our industrial environment. I only have single mode fibre to deal with. I'm curious if a IEM-3000-8FM module will connect to a 100LX SFP using a single mode fibre. I know the IEM-3000-8FM module is 100FX for multi-mode fibre. I know they both use 1310nm wave length but i'm not sure if they will work together?
View 1 Replies View RelatedI'm having difficult getting this switch to boot from flash. I do not understand why it is trying to load "b1" from "bs1" instead of something from flash. [code]
View 2 Replies View RelatedI am trying find out what the nominal power draw is for the following switch. The installation manual and data sheets says that the power draw for the units are 15.1W and 15.7W maximum at 18VDC. I am trying to use the switch for a solar application (12VDC) and would like to find out what the nominal draw would be when the device is in standby or if all of the ethernet ports are unused. I plan to use the two fiber SFP's and one copper port.
IE-3000-4TC
IE-3000-8TC
I just deployed a nexus 7010 switch at a server farm. after deployment, it was notices that there are surges in latency across the network. The default gateway was then moved to the nexus, with this pinging from an host on the same subnet there is intermitent burst is latency
NEXUS>>>>>Server
Ping of about 80ms and sometimes even times out.
To me, this is strange.
NX-OS Version is 5-02a
We are facing issue of high Latency and slowness with Switch Cisco 4507R at the Customer site.show logging for the Switch and if there is any IOS related issue [BUG] or some other finding for this case.
View 1 Replies View RelatedI am looking for any assistance with an issue I am having. Within my network, I have two Net App enclaves that replicate with each other. These hang off of separate switches, one at our primary site and one off of our secondary site, just a few miles away. I can replicate from the primary site to the secondary site at 8GB per minute. From the secondary site back to the primary site, however, the replication passes at about 17MB per minute.
The configuration is exactly the same on both ends. The primary Net App enclave hangs off of a 6513 switch and the secondary Net App enclave hangs off of a Nexus5000. Trace routes and pings all show correct paths and connectivity. I have troubleshoot this for a few days and I have been unable to figure out what is causing the replication issues. The fact that this is bi-directional traffic and I am having problems one way is really throwing me off. There are no ACLs or firewalls present between the two switches.
i have a cisco 3560x poe. ny currnet version is 12.2(58)SE2.the cpu process is aboute 30% average.my problem is- ping to the switch itself show me 12ms which is high latency.*note- data between two hosts no this has no latency.i realize the packet go into the cpu itself but, the cpu is not loadedusy. so my question is- is this natural behavior?
View 2 Replies View RelatedMy network Infrastructure consists of 2 core switches(cisco 3950, 24 port) and 3 access switches (cisco 2960G, 48port). No distribution layer.Both Core switches are connected to the BVI of a VPN router.PVST is running in all switches. The STP results are all good. We have 3 VLAN's in the LAN an IP routing is enables in the core switch. The network diagram is attached.
The issue we are facing is that , we get intermittent packet drops while pinging towards the access switches, and there is always a higher latency towards these assess switches.These issues are present even with no other users using the LAN. But these issues are not present while pinging towards the GW.
I guess, it is because of this, we have issues the accessing file server in the LAN. How do we go ahead with the troubleshooting. Will upgrading the IOS resolve this.The present version details is..
WS-C2960G-48TC-L 12.2(44)SE6 C2960-LANBASEK9-M
Where can I find the GSD file for IE3000?
View 2 Replies View RelatedI play an online game, and latency is critical. I usually play at one server, and typically I get around 100ms ping. Today, when I joined the server I noticed my ping is now 40-45ms. My IP has not changed, internet service has not changed, service of server has not changed. It's almost as if the latency *just got better*. I know there are probably a huge number of factors regarding this, but I'm wondering how I could investigate this. Preferably, I'd like to keep my latency at 40ms, but I have no idea how it got there.
View 1 Replies View RelatedI have a 3560E with 2 vlans that I want to route between. one device with 2 vlans and route between.Interfaces are configured as such:
int g0/11
switchport mode access
switchport access vlan 10
int g0/12
switchport mode access
switchport access vlan 11
[code]...
Laptops on each port with 10.10.10.2 and 10.10.11.2 configured on them. I can ping from 10.10.10.2 to 10.10.11.1, but not to 10.10.11.2.What do I have to configure to be able to get the 2 laptops to talk to each other?
I have a spare Cisco 857w that I am playing around with to learn.I managed to reset it to default, upgrade the ios to 12.4 However for the llife of me I cannot ping this device.
View 1 Replies View RelatedI just found out that one of our 10 3750's has been assigned with an IP Address that is in conflict with a PC that has been in production long before this 3750 was deployed in our environment. Good thing it is servicing devices on a separate vlan. The conflict IP Address is assigned to the default vlan of the switch so we can connect to it from the core.If I change the IP Address of the switch, will it reboot and momentarily disconnect the devices connected to it?
View 14 Replies View RelatedI have a /28 subnet between my internal and external firewalls for L3 connectivity. On our internal firewall, I have a default route for internet traffic pointing to the external firewall (10.10.1.2).
We will be inserting a web filter appliance as indicated on the diagram. The appliance requires an IP address to be assigned to the LAN interface.
What is the best way to accomplish this with minimal impact? Will my default route on my internal firewall have to change to the IP of the web appliance if I address the web appliance on the 10.10.1.x subnet?Should I address the web appliance on the 10.10.1.x subnet to begin with, or create a vlan on the 2960 and a L2 interface on one of the firewalls?
I hope I'm posting this in the correct place. I have a 2610 router and on starting it up i get this and only this,
"System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by Cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info"
thats all and exactly what is displayed on the console screen the device is none responsive.
I have one specific trouble with Catalyst 3560CG switch and Stardom reserved industrial controller. Controller has 2 processors, one of them after(!) negotiation become main with IP 192.168.1.1, other one stays in reserve with IP 192.168.1.129. If main one shuts down, spare one becomes main with IP 192.168.1.1. This perfectly works with DLINK and MOXA level 2 switches, but fails with Catalyst 3560, because spare one cannot even connect to switch port. I don't know the exact reason of it, but i suspect, that it happens because of before negotiation both controllers have ip 192.168.1.1 (i know, that it is wrong and weird, but so it goes). First of them correctly connects to switch port, which goes up and passes pings. Second processor tries to connect to switch port, which goes several times up and very soon down, then processor lefts his tries to connect to anybody and become idle. The switch seems to some way check IPs of 1-st and 2-nd port packets, and shuts down 2-nd port. I have connected via hyperterminal and tried to disable some level 3 functions and checks of the switch, but this wasn't useful. how exactly(or at least approximately) should i configure a switch to make this bundle work?
View 1 Replies View RelatedI cannot ping and end node on my system from my Cisco 2911. I've tried to configure my computer to ping the device and I am able to. It seems the difference between using my computer and the 2911 is that with my computer I am able to set the default gateway as the end node's ip.
View 1 Replies View RelatedMy environment have two device ,a cisco css11501 and a cisco 2960 ,when I reboot CSS11501 then 2960 shutdown fa0/41
I command "sh logging | in 0/41" just up down two time,not five times in 10 seconds
.May 17 11:13:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to down
.May 17 11:13:19: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to down
.May 17 11:14:53: %PM-4-ERR_DISABLE: link-flap error detected on Fa0/41, putting Fa0/41 in err-disable state
.May 17 13:44:35: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to up
.May 17 13:44:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to up
My company is composed of three different campuses, all with a similar network topology. We currently are experiencing high bandwidth on our serial interface at one of the campuses in particular. The network is composed of about 20 VLANS routed internally using a Cisco 6509. Traffic to the outside is PAT’d by an ASA 5510 and then forwarded through our edge router interface. Each VLAN is PAT’d to a specific public address.Due to the PAT, how would you recommend determining what specific private addresses are consuming our resources on the serial interface. When I look at our NMS, it reports the public address, but that only narrows it down to a VLAN. For example, all the devices in VLAN 6 are translated to 146.34.118.245, and 146.34.11.245 is a top talker.
View 1 Replies View Relatedi have a device connected to 2960 switch. It is an access port and i could ping the device from other switches , also from outside the lan. But i am not able to ping the device from 2960 switch alone. I suspected and checked the arp table and it was showing as incomplete. I created the manual arp entry and tried pinging but no luck.
View 14 Replies View RelatedI'll have to replace an old WS-C3550-24. Reasons for this: EOL/EOS & we'll need a NAT capable device...
As I understood, the only L3 catalyst that is able to perform NAT is a 6500? Is that correct? If the above is correct, it seems I can only replace the setup by using a router/ASA with a L2 switch. A router with high throughput (+/- 300Mbps) is hard to find, especially as NAT will require CPU resources...
So, my best (affordable price) solution is getting an ASA5520 (450Mbps FW throughput) and a L2 switch?
Cisco LMS 4.0: Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address? • Traps contain the original Device Agent IP to identify the source (Not the IP of LMS)?• Is possible to configure one logical IP address or Domain Name for redundant LMS:Cisco Security Manager 4.1:Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address?• Traps contain the original Device Agent IP to identify the source (Not the IP of Security Manager)? • Is possible to configure one logical IP address or Domain Name for redundant Security Manager?
View 0 Replies View Relatedwhen am trying to plug a PC into the switch, it takes power as the switch is POE . but when trying to plug IP Camera Device it does not take any power. although i have cisco 2960 - 24 ports both PC and IP Camera getting power. while troublshooting by #show power inline , i get nothing as well.
View 6 Replies View RelatedI have some 2960 switches with Lan Lite ios in my infrastructure.And I try to configure them to support "trust device cisco-phone" and "switchport priority extend cos 0" on ports with cisco phones.But LAN Lite image does not support "mls qos trust device cisco-phone".can I use any workaround to trust cos of cisco phone and to remark PC traffic with cos 0?
View 1 Replies View RelatedThis is regarding CISCO logging configuration.We palnned to implement enable logging on all the cisco nexus switchs.we are running HP arc sight in our DC this device monitor all the CISCO devices.We want to enable logging with this Arc sight device.Just I would like to know about config commands for Nexus device, what is the command to enable logs which is include "who is login & logout?, interface down information?,who was did conf t ? & every logs"
View 8 Replies View RelatedI have a 2911 router where I was configuring the device to allow remote desktops connections. Everything is working properly, but for some reason my ACL has disappeared.
View 5 Replies View RelatedI'm looking to configure a syslog server for all of my cisco device logging. I've had a look at CNA and can't find any options to define a syslog server for my switches.
What's the best way to define a syslog server and the severity of the notifications? Also, i'm looking to clear all previous Syste mmessages fon my devices?
I have a 512MB USB Flash device and was able to boot the IOS on the C2960 from it.After that i tried to Copy the IOS file from the USB to the system flash, but it could not find the USB Device.At plugging in the device the systems tells me: "Transfer type 2 not supported" I configured the USB device in NTFS and FAT both are able to boot with the ROMMON, but the normal system does not accept them and i know i can do the copy over a TFTP from my laptop, but it is strange that rommon accepts the usb device and the system does not?
View 1 Replies View Related3750 can not support multiple subnets in it's DHCP server pool config.
Is this an issue that can be fixed with a different iOS or is there a different Cisco switch that I can replace the 3750 with that will handle multiple subnets within an individual pool?
NEXUS 7000 Octopus internal error in device 78 message. I got this on NEXUS 7000 logs:
Nov 12 22:05:14 smale-outside : 2012 Nov 12 21:05:14 BRST: %MODULE-2-MOD_DIAG_FAIL: Module 2 (serial: JAF1548AMKB) reported failure on ports 2/1-2/32 (Ethernet) due to Octopus internal error in device 78 (device error 0xc4e0025b)
Nov 12 22:05:17 smale-outside : 2012 Nov 12 21:05:17 BRST: %MODULE-2-MOD_FAIL: Initialization of module 2 (serial: JAF1548AMKB) failed
Nov 12 22:05:18 smale-outside : 2012 Nov 12 21:05:18 BRST: %MODULE-2-MOD_FAIL: Initialization of module 2 (serial: JAF1548AMKB) failed
[code]....
I only have found:
[URL]
which does not match reality : No one was configuring Vlans.
I have a c3560 that on Port 1 I can not get any device to talk to the DHCP server.Previously there was a client connected to this port however over the weekend he stated he lost connectivity.
In my troubleshooting I have connected that client to another port and now he is good to go...I connected my laptop and tried to connect to the network however I could not.I checked the logs and did not see anything that lead me to think it was having problems.
Is there another way to shut this down and hopefully start it back up without having to restart the entire switch?
I have a Cisco SG200 26 Port Switch, 2 Cisco WAP4410N Access points, and a VLAN aware Router. I have created 4 VLAN's. For the sake of this conversation lets call them.
98 - Intel Vpro
99 - Management
100 - General
101 - Guest
The Access points are capable of doing V LAN tagging so I plan on having them tag a guest network as V LAN 101. That can get sent to the V LAN aware router and out. No problem. I have some devices, or management pages that I don't want accessible from the general network. (Intel V pro KVM, Remote Management Cards, AP Config Menus, Switch config menu...) . I need to be able to take a V LAN unaware device, plug it into port 1, and have it communicate with V LAN 98, 99 and 100.