Cisco VPN :: RV082 Firmware And Windows 7 VPN Connections?
Feb 16, 2012
I would like to get either the Cisco VPN client to work or just to be able to connect with the Win 7 VPN connection. These are dynamic client IPs btw.I've made all the necessary accounts through the Web Management console but haven't had much luck so far. I did enable PPTP server and disabled "Block WAN Request" today to try again while remote later.
I think this is the v1 model. It has A00 on the back and I know of no other way to tell which version it is.
My other concerns is that the firmware is 1.3.98-tm and would like to update this to v2.0.2.01 . We have 2 remote VPN static IP users with existing connections that seem to be working fine (the admin that configed these is no longer here). I'm afraid to update the firmware in the event that this would cause some problem for them to reconnect. This article at the link below stated that a previous firmware ruined his connection and wouldn't allow him to revert back to the previous firmware. [URL]...
Is this true for all firmware upgrades for the RV082? Can you not restore to the previous firmware? If not, might it cause any configuration or reconnect problems for the existing VPN Tunnels if it works without other issues?Also, is the Cisco VPN client capable of connecting from WIndows 7 Home Premium?
View 1 Replies
ADVERTISEMENT
Mar 25, 2012
RV082 - 1.3.2 I need to have RDP and pcAnywhere enabled to a customer site for remote support, but need to limit the incoming IP ranges to only our offices. I have the port forwarding set up and tested working. I then set up rules to deny all traffic on the needed ports and added rules to allow a few IP ranges from our office locations. I even tried a rule allowing all traffic from our main office but that also failed to allow RDP or pcAnywere connections.Now I can no longer connect from any of our remote offices. I followed the limited instructions that I found in another post but its not working.
View 1 Replies
View Related
Oct 18, 2011
Do Cisco recommend me running the latest firmware update? Im just an individual who uses it for like a small web-/FTP-/Mail-server, etc. What are the recommendations? Personally I would have updated to the latest...but what are actually the Cisco recommendations?
View 3 Replies
View Related
Sep 13, 2011
I have an old RV082 with firmware version 2.0.0.19. I want to replace it with a new RV082 firmware version 4.0.2.08.I exported the fv2 config but can't restore it on the fv4. I get "invalid file type" error. The fv4 box is looking for a .config file and the fv2 box saves as a .exp file.
View 4 Replies
View Related
Sep 4, 2011
I have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.
View 1 Replies
View Related
Dec 1, 2009
I have upgrade the firmware on several RV082 (and RV042) model routers, and all of them have had subsequent WAN connectivity loss. The WAN works for a while, then stops working until the router is restarted, then fails shortly thereafter. I would assume it was some configuration corruption on incompatibility with the upgrade, but the symptom has been universal. EVERY 2.x upgrade I've made to a RV082 or RV042 router has exhibited this symptom. Reverting to the 1.3.98-tm firmware fixes the issue.
View 14 Replies
View Related
Jul 6, 2012
This morning i upgraded a remote RV082 to 4.2.0.1 from 4.0.4.1. Numbers could be off slightly since i'm going from memory. I never got the normal acknowledgement the transfer was complete but after an ample amount of time closed the tunnel from my end, re- established my vpn but when i went to log in i received: RV082 firmware upgrade error? The requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist./quotei googled it and found similar occurrences with earlier upgrades. I'm assuming it didn't reboot itself upon completion of the xfer, at least i'm hoping a cold reboot will correct this but as i'm remote and this install doesn't have an ethernet power controller i'm stuck until monday. Should i bring a spare RV082 just in case.
View 3 Replies
View Related
Nov 2, 2011
RV082 Firmware Version 2.0.2.01-tmRV082 Firmware Version 2.0.2.01-tm
View 1 Replies
View Related
Nov 21, 2012
I have a Cisco RV082 and can successfully connect with the Cisco QuickVPN Client, 1.4.2.1. However, after 1 to 5 minutes I see the Windows 7 bluescreen indicating that the system has halted due to a problem with a driver. I have installed the latest Windows updates and reinstalled the client.
The bluescreen only occurs if I use the Cisco QuickVPN Client.
View 4 Replies
View Related
May 29, 2013
I installed QuickVPN v1.4.2.1 as it was in the download section on Linksys: [URL]
for the RV082 router we have. It connected but the program seemed buggy as there seemed to be no way to close the program after I used it so I wanted to uninstall it and install a more recent version of QuickVPN (side question: is it possible to VPN connect to my RV082 router with a different version of QuickVPN?).
I have Windows 7 Professional 64bit SP1 with all the latest updates. When I try to uninstall the program, at about the 25% mark of the window for 'QuickVPN Client Setup is preparing the InstallShield Wizard, which will guide you through the rest of the setup process. Please wait.' it seems to stop responding as holding the mouse over that windows just displayes a ring which goes round and round. I regret installing this buggy software on my PC.
View 3 Replies
View Related
Jul 18, 2011
I have recently acquired one of these routers. I thought, being a Cisco product, it would be the bee's knees. It is not. After finally getting the network set up - no mean feat, although I do not claim any expertise, but had to resort to some other network management software to finally get it all running - the router drops either the WAN connection or the wireless connection many times a day. The laptops often show as being connected to the network/router, but are unable to access either the internet, or the router via the browser. Re-booting the router is the fix, but, hey, I can achieve that sort of performance with any old $20 router - none of my old Net gear routers was this troublesome.
The permanent fix would seem to be a firmware upgrade, but guess what? The only options available under the "Administration" tab are time setting and switch settings - no firmware upgrade. The supplied firmware is 1.01.09(001) Apr 7 2010. Why these products are supplied, as new, without the latest firmware installed beats me, but there you go.
View 4 Replies
View Related
Jan 17, 2010
Recently I sold a rv082 router to a client.He uses a Windows XP environment to dail in using QuickVPN.A week ago an office admin wanted to connect using Windows 7 and it does not work.The client starts do dial and connects but the connection does not work.The admin does not use a router and there is no active software firewall.
View 3 Replies
View Related
Jun 5, 2012
I have a E3200 and upgraded the firmware last weekend to 1.0.0.4 and now I get dropped connections every few minutes. I was working form home and VPN into a west coast client and was getting dosconnected every few minutes so I thought it was possibly their VPN but when I checked my outloook it was also disconnected and is not associated with their VPN. I called Comcast and they said the modem has been online for 19 days so now everything points to the router.
View 5 Replies
View Related
Aug 7, 2011
I have a dual boot computer - Vista Home Premium and Windows 7 Home Premium. When booted into Vista I can map my Network and connect to the Internet, a network printer (ethernet) and a second Windows XP computer. When I boot into Windows 7 I can still access the internet and my networked devices but I cannot map my network. Also, the network system icon (bottom right-hand screen) shows erroneously that no connections are available - but clearly they are! The attachments show the status of my Vista and Windows 7 connections. The only thing that appears to be odd is that my Windows 7 system is set to 'Public' and my Vist system is set to 'Home'. I have tried all manner of things to change Windows 7 to 'Home' but to no avail.
View 14 Replies
View Related
Apr 12, 2011
How can I disable UDP connections in Windows Vista and XP?
View 6 Replies
View Related
Feb 24, 2012
I have an issue at my work where we are trying to added another computer to our network. We have 3 computers on XP (Included our server) and 7 on windows 7, 10 total.Now I've just tried adding the 11th PC and had no luck connecting to the server, but i do have internet access. I am aware Win7 allows 20 max connections, would we upgrade our server PC to Win7 and leave the other 2 computers on XP will I be able to add this 11th PC? Or do I have to upgrade all the remaining XP machines to win7 to get the result I'm looking for.
View 2 Replies
View Related
Jan 10, 2013
I had a Sony Viao with Windows Vista for some years and I managed to create a bridge using the Sony Viao laptop and my o2 usb modem. That was some time ago and now I have a new laptop with Windows 7 ?I have to mention that I do not have wireless connections. I have an o2 modem and an ethernet cable. They are the only two connections that show up in my internet connections. The LAN connection has an image of a ethernet cable connection while the o2 connection has an image of a phone.whenever I watch youtube walk throughs it never looks like my set up. Ive tried everything over and over. Turning off UAC, turning on sharing but nothing has worked yet. When I just select the LAN connection and right click there is an option to Bridge. When I right click the o2 connection its not there. When I select both the option isnt there either.
View 2 Replies
View Related
Oct 6, 2011
I ve just finished setting up my first serial connections between two sites using Cisco 1800 routers. I can make connections from Site A to Site B using Windows XP clients, eg accessing exchange server 2007 running on Windows 2003x64, but the main problem is that when I try to configure Windows 7 clients to connect to exchange server on the other site, I can't make connections , no ping, no ssh , no http. What amuses me more is that I can connect to Windows 2008 servers using both Windows XP and 7.
View 5 Replies
View Related
Aug 29, 2011
There was a big storm last night, and when I woke up I found that I couldn't connect to the internet. I have my computer plugged into the cable modem. The Windows network status says "Not connected, No connections are available". The onboard NIC that I had been using is no longer showing up in the device manager. I figured lightening might have knocked it out, even though my computer is behind a UPS and surge protector, so I bought a PCI ethernet card. This installed correctly and is showing up in the device manager, but I'm still getting the same error. When I unplug the ethernet cable, there is no change in the status.
View 6 Replies
View Related
Jul 16, 2011
I have to connect/switch to two different ips different gateways, can I possibly keep two set of ips always ready.
View 1 Replies
View Related
May 5, 2012
I turned on my Netbook (Packard Bell NAV50, Windows 7) the other day and it would not connect to the internet. Not only won't it connect, but I can't even find any wireless networks, the icon in the bottom right just has a red cross. I'm currently using another laptop which can detect the network and next doors too so it is not a problem with the router. My PS3, phone, iPod etc also all connect fine. I've checked the fn f2 thing and that is definately on and working. Also when i click on "change adapter settings" in "network and sharing centre", it is there and is enabled and has the full green symbol icon but also has a red cross.
View 6 Replies
View Related
Jul 3, 2012
I have recently bought an Samsung UE32ES5500 and I want to connect it to the internet. Not wanting to buy an expensive Samsung wireless adapter for the TV, I've decided to use an ethernet cable. Because the Internet cable passes through underground to the bedroom and the TV is located in the living room, i decided to put a router in the bedroom, and receive it's signal in the living room using a windows 7 laptop.Afterwards I connected the laptop to the TV through an ethernet cable, and bridged the two connections in Network Connections in Control Panel on the laptop. The TV successfully finds the laptop (and the router I think) but still cannot connect to the internet.
View 1 Replies
View Related
Sep 26, 2012
We are still using some old WRV54G wireless VPN routers for work. Can we get new vpn software that will work with these routers? The quickvpn client software we have no longer works after we last updated the firmware. How can we set up vpn connections using tunneling?
View 1 Replies
View Related
Jul 24, 2012
We have a newly-purchased RVS4000 v2 with firmware v2.0.2.7. Its intended role is as a gateway between our local network of wired workstations and a Cisco 2800 series Integrated Services Router, which is at the receiving end of our T1 line. It is configured with static IPs on both the LAN and the WAN side. It does NOT serve DHCP for the LAN. Ever since I installed it, I have had repeated complaints from users of Vista and Win7 workstations that they lose internet connectivity about every 20 - 30 minutes or so. The only solution is to unplug the workstation's CAT5 cable, count to 30, and plug it back in. Then everything's hunky dory for another 20 - 30 minutes. Meanwhile, all our Windows XP and Linux workstations enjoy uninterrupted internet access. The router/gateway we replaced (a DLink DIR-130) never had this problem.
View 4 Replies
View Related
Nov 9, 2009
I have a RV016 Router with 3 internet DSL conections.
Firmware version : 3.0.0.1-tm (Jun 6 2008 20:17:06)LAN IP : 192.168.11.254 /24WAN1 IP : 192.168.1.253 /24WAN2 IP : 192.168.2.253 /24WAN3 IP : 192.168.3.253 /24MODE: Gateway.
Windows Messenger continually connects and disconnects. This behavior is permanent I only have problems with Messengers (all releases), web page access is correct. I check bandwith saturation and It's ok, I use less than 50% of each DSL. I configured the correct size of MTU for each DSL and the problem continues.Is there any way to set priority to this service? Is there any way to check if the "load balance mode" affect this kind of connections?
View 12 Replies
View Related
Dec 15, 2011
I have a Toshiba Tablet PC that came with the configfree software. It worked fine for a while but then it started giving connectivity problems. I tryed to disable Configfree by all means possible to no avail. Then I decided to uninstall it successfully, but I still can't return the network connections control to windows. It seems like it is still under configfree. My guess is that some internal switch at the registry level is still saying that the wireless control is not windows.
View 1 Replies
View Related
Sep 5, 2012
So I just installed Windows Server 2003 64 bit on an older HP Proliant DL360 G5 and am trying to connect it to my network but neither of the 2 NIC's are showing up under Network Connections... the only option I am given is the ''Add Network Places Wizard''.
I have an ethernet cable plugged into NIC 1 and the LED's work so I know it's not a bad NIC card- do I have to download drivers for the NIC? Do I download them to a USB/CD and then just boot from that?
View 1 Replies
View Related
May 10, 2011
Is there any way to allow multiple computers to connect to the same remote computer and work simultaneously?
View 3 Replies
View Related
Jan 23, 2012
When I turned on my laptop today I noticed there was a new icon in my Network Connections section. It's called Internet Gateway. I haven't downloaded anything (weird or otherwise), I'm still able to connect to the internet and nothing seems to be amiss.
View 6 Replies
View Related
Oct 10, 2011
I'm currentlly running Both Wired and Wireless GPO via Win2008r2, on my WIRED connections after clt-alt-del logoff my network connection stays open (pingable)While connected via wireless (WLC 5508 and WCS) Windows AD 2008r2 ;Radius Server 2003.
All Clients authenticate using Network Authen (Wireless Network Connection Properties) WPA2 Data encryp AES EAP type PEAP.Authentication Method (EAP-MSCHAP) I have no problems connecting via SSID etc... my Question is how do I keep the TCP connection open after initiating a logoff from Windows. (Closing network connection) OPEN!
I need to maintain a tcp(pingable) connection open in order to access Manufacturing clients that are connected via WIFI. (WLC).All wireless clients are issued and auto-enrollment cert via IAS .
View 8 Replies
View Related
Feb 8, 2011
Network connections lost Windows 2003 Server, Reload Drivers Still not working.
View 28 Replies
View Related
Feb 15, 2012
I have two Windows 7 Ultimate computers and around 10 Windows XP (Home and Professional, SP2 and SP3) computers trying to connect to it. It's just a LAN (no internet access).I have set all of the password-protected sharing off on the Win 7 systems. I have tried opening up ALL of the permissions and such (since security is not really an issue).When I try to map the network drive, it won't let me merely connect to it. So, I have to click map network drive on the XP computer and hit "login with other credentials" and enter the username/pass for the user account on the Win 7 machine (we'll say Bob for user and Smith for password for the sake of example). It will mount the share (which is actually the C: root of the drive) just fine.
The only problem is the moment you restart the Windows XP system, it will lose the connection. My fix for it was to create a .bat file that contained the following: [code] I put it in the Progam FilesStartup folder to run upon boot. For the most part, it seems to work after a fashion. Some of the computers, though, will drop the connection to the two Windows 7 systems and need to be rebooted 1-2 times before they get it back again. Even clicking the .bat file manually will have the same result (you will have to reboot) if it drops the connection while you're using it. Plus, sometimes it doesn't map the drive correctly (I assume because the batch file is running before the connection has a chance to initialize on the LAN).I've also tried adding an "Everybody" user to the permissions on the Win 7 systems with full access, but it only seemed to cause problems with the existing connections.It might also be prudent to mention that both the Windows 7 and Windows XP systems are all 32 bit. I've also disabled the firewalls on the two Windows 7 systems. Neither of them have any antivirus or security software installed.
View 2 Replies
View Related
Oct 2, 2011
I have just moved homes and I am unable to connect wirelessly to the internet through the network in my new house. The computer is connected to the network with excellent signal strength but access shows as local only and will not connect to the internet.
All other computers have been able to connect to the internet with no problems, and my computer will connect to other wifi connections, no problem.I can connect with a wire directly to the router, but no luck with wifi. I have also had this problem with one previous wifi network. I have tried many things, including taking the compter to a computer shop for them to look at and having another professional look at it, but so far no luck.
Tech Support Guy System Info Utility version 1.0.0.1 OS Version: Microsoft� Windows Vista� Home Premium , 32 bit Processor: Intel(R) Core(TM)2 Duo CPU T5550 @ 1.83GHz, x64 Family 6 Model 15 Stepping 13 Processor Count: 2 RAM: 2037 Mb Graphics Card: Mobile Intel(R) 965 Express Chipset Family, 448 Mb Hard Drives: C: Total - 102720 MB, Free - 27457 MB; D: Total - 11750 MB, Free - 1681 MB; Motherboard: Hewlett-Packard, 30D9, 83.21, CND8173S5Q Antivirus: AVG Anti-Virus Free, Updated: Yes, On-Demand Scanner: Enabled
View 11 Replies
View Related
