Packard Bell NAV50 / Windows 7 - No Connections Available
May 5, 2012
I turned on my Netbook (Packard Bell NAV50, Windows 7) the other day and it would not connect to the internet. Not only won't it connect, but I can't even find any wireless networks, the icon in the bottom right just has a red cross. I'm currently using another laptop which can detect the network and next doors too so it is not a problem with the router. My PS3, phone, iPod etc also all connect fine. I've checked the fn f2 thing and that is definately on and working. Also when i click on "change adapter settings" in "network and sharing centre", it is there and is enabled and has the full green symbol icon but also has a red cross.
View 6 Replies
ADVERTISEMENT
Oct 7, 2011
My wife's Packard Bell EasyNote AJ300 has been working wirelessly from the same place for a couple of years. Now the task bar icon shows no handshake with the Netgear DG834G router 4 times out of 5 attempts. It seems to work if moved to the same room. On line issues (BTinternet) with my ethernet connected pc meant resetting and changing the router config. under instructions from Netgear support but that did not seem to affect the laptop at the time (6 weeks ago) (BT reset something in the exchange which fixed the fault) The laptop has not been used much till recently so there may be a connection.
View 2 Replies
View Related
Feb 15, 2011
I have a Packard bell easynote R1938, which the motherboard died I bought one from ebay and stripped down the laptop to install the new board.It all went well Laptop back in a running state apart from the WIFI, the card is back in its original place and being detected by WIN XP. The problem is that the card status is 'WIFI is turned off use hardware switch to turn back on', now I know the hardware switch is tied into the keyboard under FN + F1 but it does not control the WIFI.I am wondering if there is any other way of turning on the WIFI?? or if the problem is one of drivers needed for the hardware switch as I do know there is an unknown item in the device manager but I couldn't find any drivers for the unknown.
View 3 Replies
View Related
Apr 23, 2011
Just bought a new Packard Bell Easynote laptop and even though it can detect my secure connection with BT it uses an unidentified connection and won't connect.
View 1 Replies
View Related
Oct 31, 2012
Where i find network driver for Packard bell pav80?
View 3 Replies
View Related
Mar 30, 2011
how can install wireless adopters on my packard bell laptop and which website can i find them?
View 1 Replies
View Related
Dec 4, 2011
I would like to find out why my packard bell laptop doesnt print wirelessly to my Lexmark 7600 printer. It prints only when the printer cable is plugged into the computer. My laptop works wirelessly with no problems generally
View 1 Replies
View Related
May 26, 2012
Packard bell alp ajaxc3 notebook has suddenly lost wireless,it has been working for about 18 months with no problems,the system is windows 7.first tried system restore about three times,no luck the toolbar shows the icon with a red cross but check the device manager and it shows the atheros adapter as working properly.tried ip config and it says everything is disconnected and the adapter as switched off.there is no external switch and I can't find any info on the net as to a software switch.the router is ok because my granddaughter dell works ok and I have two others with wired connects.even tried a windows repair via the install disc without luck,tried another adapter which it recognized and installed with the same result have been through the forum and tried everything that remotely resembled my problem,same result.
View 4 Replies
View Related
Sep 24, 2011
I have a Packard Bell mx37 easynote laptop and i have recently installed vista after using Ubuntu. But now I cant connect to any wireless networks? When I click on the connect to a network in the bottom corner the box does not show scanned networks, all that rads is "Windows cannot find any networks" (the router is will in range (~2m)) then when i click "diagnose why I cant find any networks" it tells me that the "network adapter is not installed and configured"
View 1 Replies
View Related
Jun 29, 2011
A couple weeks ago every device on my wireless network started disconnecting from the internet in unison and seemingly at random and then reconnecting. The time between these disconnects varied anywhere between almost immediately after regaining a connection and three to four hours later. As things stand I have a SpeedStream 5200 modem running into a D-Link DIR-655 wireless router. I have had no problems with internet connectivity up until this point. During each disconnect, every device remains connected to the router. I've called Bell and they claim there is no issue with the modem. To test their theory, I bypassed the router altogether, and attempted to connect through an ethernet cable, but to no avail, as the now hardwired device continued to get disconnected. These failures seem to be occurring between noon and 10 p.m. and to be honest I'm amazed that one has not cut this post short.
View 5 Replies
View Related
May 5, 2011
I just got an Xbox and live and tried to connect to my Bell Turbo Hub but it came up with a not enough MTU error, I called Bell and they said It wouldnt work with live. If there is some way to make it work?
View 3 Replies
View Related
Nov 8, 2011
I fiddled with the configure screens using the admin/admin id/password and using the settings from the modem I was given from YAK I now have the SpeedStream 6250 working! If you enter in all the addresses into the various locations the modem will work. Even though it's the Bell interface"
View 2 Replies
View Related
Aug 7, 2011
I have a dual boot computer - Vista Home Premium and Windows 7 Home Premium. When booted into Vista I can map my Network and connect to the Internet, a network printer (ethernet) and a second Windows XP computer. When I boot into Windows 7 I can still access the internet and my networked devices but I cannot map my network. Also, the network system icon (bottom right-hand screen) shows erroneously that no connections are available - but clearly they are! The attachments show the status of my Vista and Windows 7 connections. The only thing that appears to be odd is that my Windows 7 system is set to 'Public' and my Vist system is set to 'Home'. I have tried all manner of things to change Windows 7 to 'Home' but to no avail.
View 14 Replies
View Related
Jan 14, 2013
i am setting up a windows server 2008 to be used as a nas on my bell modem network that my pc is also on. the bell modem is then connected to a dlink 655 router by lan on the bell modem to wan on the dlink. the dlink is used for wireless connections to the laptops in the house. my problem is that the laptops cant see my nas but have access to the internet. should i switch my program for the nas from windows server 2008 to something like free nas or can i change setting in my router and modam?
View 1 Replies
View Related
Apr 12, 2011
How can I disable UDP connections in Windows Vista and XP?
View 6 Replies
View Related
Feb 24, 2012
I have an issue at my work where we are trying to added another computer to our network. We have 3 computers on XP (Included our server) and 7 on windows 7, 10 total.Now I've just tried adding the 11th PC and had no luck connecting to the server, but i do have internet access. I am aware Win7 allows 20 max connections, would we upgrade our server PC to Win7 and leave the other 2 computers on XP will I be able to add this 11th PC? Or do I have to upgrade all the remaining XP machines to win7 to get the result I'm looking for.
View 2 Replies
View Related
Jan 10, 2013
I had a Sony Viao with Windows Vista for some years and I managed to create a bridge using the Sony Viao laptop and my o2 usb modem. That was some time ago and now I have a new laptop with Windows 7 ?I have to mention that I do not have wireless connections. I have an o2 modem and an ethernet cable. They are the only two connections that show up in my internet connections. The LAN connection has an image of a ethernet cable connection while the o2 connection has an image of a phone.whenever I watch youtube walk throughs it never looks like my set up. Ive tried everything over and over. Turning off UAC, turning on sharing but nothing has worked yet. When I just select the LAN connection and right click there is an option to Bridge. When I right click the o2 connection its not there. When I select both the option isnt there either.
View 2 Replies
View Related
Aug 29, 2011
There was a big storm last night, and when I woke up I found that I couldn't connect to the internet. I have my computer plugged into the cable modem. The Windows network status says "Not connected, No connections are available". The onboard NIC that I had been using is no longer showing up in the device manager. I figured lightening might have knocked it out, even though my computer is behind a UPS and surge protector, so I bought a PCI ethernet card. This installed correctly and is showing up in the device manager, but I'm still getting the same error. When I unplug the ethernet cable, there is no change in the status.
View 6 Replies
View Related
Jul 16, 2011
I have to connect/switch to two different ips different gateways, can I possibly keep two set of ips always ready.
View 1 Replies
View Related
Feb 16, 2012
I would like to get either the Cisco VPN client to work or just to be able to connect with the Win 7 VPN connection. These are dynamic client IPs btw.I've made all the necessary accounts through the Web Management console but haven't had much luck so far. I did enable PPTP server and disabled "Block WAN Request" today to try again while remote later.
I think this is the v1 model. It has A00 on the back and I know of no other way to tell which version it is.
My other concerns is that the firmware is 1.3.98-tm and would like to update this to v2.0.2.01 . We have 2 remote VPN static IP users with existing connections that seem to be working fine (the admin that configed these is no longer here). I'm afraid to update the firmware in the event that this would cause some problem for them to reconnect. This article at the link below stated that a previous firmware ruined his connection and wouldn't allow him to revert back to the previous firmware. [URL]...
Is this true for all firmware upgrades for the RV082? Can you not restore to the previous firmware? If not, might it cause any configuration or reconnect problems for the existing VPN Tunnels if it works without other issues?Also, is the Cisco VPN client capable of connecting from WIndows 7 Home Premium?
View 1 Replies
View Related
Jul 3, 2012
I have recently bought an Samsung UE32ES5500 and I want to connect it to the internet. Not wanting to buy an expensive Samsung wireless adapter for the TV, I've decided to use an ethernet cable. Because the Internet cable passes through underground to the bedroom and the TV is located in the living room, i decided to put a router in the bedroom, and receive it's signal in the living room using a windows 7 laptop.Afterwards I connected the laptop to the TV through an ethernet cable, and bridged the two connections in Network Connections in Control Panel on the laptop. The TV successfully finds the laptop (and the router I think) but still cannot connect to the internet.
View 1 Replies
View Related
Jan 28, 2012
I lost DSL, requiring a reset from Cincinnati Bell. After that, the router behaved strangely, wouldn't connect, etc., so I upgraded to the latest firmware, did a bunch of hold-the-reset-button-for-30-seconds resets, etc., and it seems to be working again.BUT.... the download speeds are very slow, both over wireless and through a wired connection to one of the router's ports. I'm gettting anywhere from 60kbps to 400kbps, but it's been hovering around the 100-200kbps range. Upload speeds are fine, nearly matching those over a direct DSL modem connection.
View 4 Replies
View Related
Dec 15, 2011
I have a Toshiba Tablet PC that came with the configfree software. It worked fine for a while but then it started giving connectivity problems. I tryed to disable Configfree by all means possible to no avail. Then I decided to uninstall it successfully, but I still can't return the network connections control to windows. It seems like it is still under configfree. My guess is that some internal switch at the registry level is still saying that the wireless control is not windows.
View 1 Replies
View Related
Sep 5, 2012
So I just installed Windows Server 2003 64 bit on an older HP Proliant DL360 G5 and am trying to connect it to my network but neither of the 2 NIC's are showing up under Network Connections... the only option I am given is the ''Add Network Places Wizard''.
I have an ethernet cable plugged into NIC 1 and the LED's work so I know it's not a bad NIC card- do I have to download drivers for the NIC? Do I download them to a USB/CD and then just boot from that?
View 1 Replies
View Related
May 10, 2011
Is there any way to allow multiple computers to connect to the same remote computer and work simultaneously?
View 3 Replies
View Related
Jan 23, 2012
When I turned on my laptop today I noticed there was a new icon in my Network Connections section. It's called Internet Gateway. I haven't downloaded anything (weird or otherwise), I'm still able to connect to the internet and nothing seems to be amiss.
View 6 Replies
View Related
Oct 6, 2011
I ve just finished setting up my first serial connections between two sites using Cisco 1800 routers. I can make connections from Site A to Site B using Windows XP clients, eg accessing exchange server 2007 running on Windows 2003x64, but the main problem is that when I try to configure Windows 7 clients to connect to exchange server on the other site, I can't make connections , no ping, no ssh , no http. What amuses me more is that I can connect to Windows 2008 servers using both Windows XP and 7.
View 5 Replies
View Related
Feb 8, 2011
Network connections lost Windows 2003 Server, Reload Drivers Still not working.
View 28 Replies
View Related
Feb 15, 2012
I have two Windows 7 Ultimate computers and around 10 Windows XP (Home and Professional, SP2 and SP3) computers trying to connect to it. It's just a LAN (no internet access).I have set all of the password-protected sharing off on the Win 7 systems. I have tried opening up ALL of the permissions and such (since security is not really an issue).When I try to map the network drive, it won't let me merely connect to it. So, I have to click map network drive on the XP computer and hit "login with other credentials" and enter the username/pass for the user account on the Win 7 machine (we'll say Bob for user and Smith for password for the sake of example). It will mount the share (which is actually the C: root of the drive) just fine.
The only problem is the moment you restart the Windows XP system, it will lose the connection. My fix for it was to create a .bat file that contained the following: [code] I put it in the Progam FilesStartup folder to run upon boot. For the most part, it seems to work after a fashion. Some of the computers, though, will drop the connection to the two Windows 7 systems and need to be rebooted 1-2 times before they get it back again. Even clicking the .bat file manually will have the same result (you will have to reboot) if it drops the connection while you're using it. Plus, sometimes it doesn't map the drive correctly (I assume because the batch file is running before the connection has a chance to initialize on the LAN).I've also tried adding an "Everybody" user to the permissions on the Win 7 systems with full access, but it only seemed to cause problems with the existing connections.It might also be prudent to mention that both the Windows 7 and Windows XP systems are all 32 bit. I've also disabled the firewalls on the two Windows 7 systems. Neither of them have any antivirus or security software installed.
View 2 Replies
View Related
Oct 2, 2011
I have just moved homes and I am unable to connect wirelessly to the internet through the network in my new house. The computer is connected to the network with excellent signal strength but access shows as local only and will not connect to the internet.
All other computers have been able to connect to the internet with no problems, and my computer will connect to other wifi connections, no problem.I can connect with a wire directly to the router, but no luck with wifi. I have also had this problem with one previous wifi network. I have tried many things, including taking the compter to a computer shop for them to look at and having another professional look at it, but so far no luck.
Tech Support Guy System Info Utility version 1.0.0.1 OS Version: Microsoft� Windows Vista� Home Premium , 32 bit Processor: Intel(R) Core(TM)2 Duo CPU T5550 @ 1.83GHz, x64 Family 6 Model 15 Stepping 13 Processor Count: 2 RAM: 2037 Mb Graphics Card: Mobile Intel(R) 965 Express Chipset Family, 448 Mb Hard Drives: C: Total - 102720 MB, Free - 27457 MB; D: Total - 11750 MB, Free - 1681 MB; Motherboard: Hewlett-Packard, 30D9, 83.21, CND8173S5Q Antivirus: AVG Anti-Virus Free, Updated: Yes, On-Demand Scanner: Enabled
View 11 Replies
View Related
Sep 26, 2012
We are still using some old WRV54G wireless VPN routers for work. Can we get new vpn software that will work with these routers? The quickvpn client software we have no longer works after we last updated the firmware. How can we set up vpn connections using tunneling?
View 1 Replies
View Related
Jul 24, 2012
We have a newly-purchased RVS4000 v2 with firmware v2.0.2.7. Its intended role is as a gateway between our local network of wired workstations and a Cisco 2800 series Integrated Services Router, which is at the receiving end of our T1 line. It is configured with static IPs on both the LAN and the WAN side. It does NOT serve DHCP for the LAN. Ever since I installed it, I have had repeated complaints from users of Vista and Win7 workstations that they lose internet connectivity about every 20 - 30 minutes or so. The only solution is to unplug the workstation's CAT5 cable, count to 30, and plug it back in. Then everything's hunky dory for another 20 - 30 minutes. Meanwhile, all our Windows XP and Linux workstations enjoy uninterrupted internet access. The router/gateway we replaced (a DLink DIR-130) never had this problem.
View 4 Replies
View Related
Nov 9, 2009
I have a RV016 Router with 3 internet DSL conections.
Firmware version : 3.0.0.1-tm (Jun 6 2008 20:17:06)LAN IP : 192.168.11.254 /24WAN1 IP : 192.168.1.253 /24WAN2 IP : 192.168.2.253 /24WAN3 IP : 192.168.3.253 /24MODE: Gateway.
Windows Messenger continually connects and disconnects. This behavior is permanent I only have problems with Messengers (all releases), web page access is correct. I check bandwith saturation and It's ok, I use less than 50% of each DSL. I configured the correct size of MTU for each DSL and the problem continues.Is there any way to set priority to this service? Is there any way to check if the "load balance mode" affect this kind of connections?
View 12 Replies
View Related
