Cisco VPN :: Setup VPN Between UC540 And SR520 With Remote IP?

Apr 30, 2010

setting up a link between a Head Office UC540 and a remote SR520 which I want to use a PC and an IP Phone from. This remote site is the first of several.I've found several examples of site to site IPsec VPNs, but none with references to voice and data VLANs, do I need to worry about this or will the phone just work.

View 5 Replies


ADVERTISEMENT

Cisco Infrastructure :: CCA 3.1(1) Device Setup Wizard Not Working For SR520-FE(W)?

Jan 5, 2012

Steps to repeat the bug:

1)  Physical Reset of SR520-FE to factory defaults

2)  Run CCA 3.1(1) and connect to 192.168.75.1 using the default cisco/cisco login

3)  Under the Home Menu, click the Device Setup Wizard

4)  In Step 1, sellect the SR520 and observe that there is also a photograph of the SR520-FE(W) model displayed as feedback for Step 1

5)  Try variations of Steps 2 through 4

Note:  Step 4 has a problem because it says to plug the power into the device, but if the power was not already plugged in to begin with, we could not run the Device Setup Wizard in the first place.

6)  Step 5 prompts for a user name and password. 

BUG:  No permutations of the documented default usernames and passwords "cisco" or "admin" work.  The result is always the error dialog:Device Connectivity Status - "Failure: Not Connected.""Return to Step 1.  Make sure that your PC is not connected to a network and you follow all the instructions."A search of the web indicates others are also had this unresolved issue with previous CCA releases.

View 1 Replies View Related

Cisco Switching/Routing :: SR520-FE-K9 Initial Setup Blocks HTTP

Sep 4, 2012

I have a fresh SR520 that I only did two things to it using CCA 3.2(1):
 
1.  Assign the address of FA4 to be 1.23.456.90 with a mask of 255.255.255.252
2. Declared a static nat of 1.23.456.90 port 80 to 192.168.75.12 port 80
 
I connected laptops to two ports:

1. FA0 (DHCP assigned laptop the address 192.168.75.12)
2. FA4 with the address on the laptop set to 1.23.456.90 and mask of 255.255.255.252
 
This is an exercise to simulate a cable internet configuration I will install the SR520 into.I can ping and point my browser to 1.23.456.89 and access the web server running there on port 80 via the inside laptop.I CANNOT point my browser to 1.23.456.90 from the outside laptop and make a connection. 
 
What I am doing wrong with NAT?  (I believe the problem lies therein as I did even try telling CCA to delete the firewall and I still could not connect to the inside web server).I have a network monitor (Wireshark) on the inside and see nothing coming across.  I THINK I see successful NAT translations in the NAT logging (also in the attachment).

View 2 Replies View Related

Cisco VPN :: Server Configure At UC540 Device

Mar 20, 2011

I am facing problem while connecting my VPN server configure at UC540 device. this device is behind my ISP router. i applied port forwording of IPSEC traffice to my cisco device  which configured as vpn server. now if i try to connect with my Live IP i get the following error. [code] I test if i connect using 192.168.0.116 internally it works but if i try to connect using my Live IP it trying and trying but not connect..

View 3 Replies View Related

Cisco Wireless :: UC540 Roaming Does Not Seem To Work

Mar 1, 2012

I currently have a UC540 system with 12x aironet 1130 APs.  Seamless roaming does not seem to work, and the recommendation seems to be to introduce a WLAN controller. 

View 4 Replies View Related

Cisco Switches :: How To Config SLM224P With UC540

Dec 12, 2012

i need supports for how can config SLM224P with UC540.

View 1 Replies View Related

Cisco Routers :: UC540 - Second Public IP Not Accessible From Inside LAN

Apr 2, 2013

I have a client that just got a second public IP (x.x.x.252) for a new program. I've setup that second IP on their UC540 on the public-facing port and it's accessible all day long from the outside, no problem. The problem comes in where users from within the LAN can't see the new public IP at all; however, they CAN get to the original public IP x.x.x.250. I've looked at the rules every which way and can't see anything that either 1) only allows LAN traffic to get to the original public IP, or 2) a NAT rule that only allows the same thing.
 
[Disclaimer: I just inherited this client and their setup, so other than me adding the IP and opening ports to it, I didn't program it.]
 
Here is the port configuration:
 
!
interface FastEthernet0/0
  description $FW_OUTSIDE$
  ip address 63.234.195.252 255.255.255.248 secondary
  ip address 63.234.195.250 255.255.255.248
  ip access-group 106 in
  no ip redirects
  no ip (code )
 
I can't figure out why .250 is internally-accessible, but .252 isn't. .252 is in the routing table as a directly-connected address, but I also added ip route 63.234.195.252 255.255.255.255 FastEthernet0/0 to the routing table and it still won't go. Everything is controlled by the UC540: The internal servers do not run DNS or DHCP or even a domain. There are no NAT outside rules.

View 1 Replies View Related

Cisco Routers :: How To Make Vpn Tunnel Between SA520 And Central UC540

Aug 20, 2011

How could i make a vpn tunnel between a router SA520 and a central UC540.

View 3 Replies View Related

Cisco VPN :: UC540 Drop Flow Is Denied By Configured Rule

Jan 29, 2013

I have created a VPN tunnel between a UC540 and ASA running software version 9.1, I am unable to ping from the outside from a network 192.168.10.0 / 24 coming in on the outside interface to the inside network 172.16.1.0 /24. I have tried various commands and some of them may not be necessary. [code]

View 3 Replies View Related

Cisco Wireless :: 7921 Wi-Fi Phone Calls Have No Audio With UC540 And AP541n

Mar 24, 2010

We have a new deployment where we have 5 total 7921G wifi phones connected via 2 AP541n access points, one connected to a ESW520p switch and then to the UC540 and the other connected directly to the UC540.  The wifi phones are intermittently giving no audio when calling each other, however, calls to the PSTN consistently do have 2 way audio.  Is this a security issue perhaps?  We are running the latest CCA software pack as this is a brand new deployment, also the AP's were upgraded to the latest firmware.

View 14 Replies View Related

How To Setup Remote Management

Jan 4, 2012

how to setup remote management...

View 4 Replies View Related

Cisco VPN :: Setup Remote Access Using ISR 2801?

Mar 23, 2011

I was trying to setup an Remote Access VPN using ISR 2801. I was able to establish the vpn tunnel from my house using DSL Connection (behind NAT), the ISR give the IP address which is from the ip pool that I configured on the ISR. The problem that I have right now is that it fails reaching the corporate LAN network.
 
[code]....

View 6 Replies View Related

How To Setup Remote Control Console

Feb 10, 2011

how to Setup remote control console

View 1 Replies View Related

Cisco VPN :: Setup A Vpn Connection At Remote Offices With A 5505?

Apr 11, 2011

I have setup a vpn connection at my remote offices with a 5505.  At my main office I have a 5510.From my remote offices I can PING my Main office server.  However when I go to set up a vpn connection through windows network and sharing center I can't seem to have the connection connect.....

View 15 Replies View Related

Cisco VPN :: Setup Remote Access In 1841 Router?

Aug 12, 2012

I am trying to set up Remote access vpn in 1841 router. The vPN client is connecting to router, but cannot ping to remote LAN Here is the config.
  
Current configuration : 3625 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption

[code]....
 
I am not getting any hit on the deny statement of 102 when i try pinging to client ip address (10.0.0.10).

View 2 Replies View Related

Cisco VPN :: ASA 5510 - Remote Access Setup / Keep Getting Logs

Apr 17, 2011

I have a problem with ASA 5510 8.0(4) This is a remote-access VPN setup and it's functional, no problems here...

But I keep getting logs like this every few seconds:

Group = <censored>, Username = <censored>, IP = <censored>, Reaper overriding refCnt [0] and tunnelCnt [0] -- deleting SA!
Group = <censored>, Username = <censored>, IP = <censored>, SA lock refCnt = 0, bitmask = 00000080, p1_decrypt_cb = 0, qm_decrypt_cb = 0, qm_hash_cb = 0, qm_spi_ok_cb = 0, qm_dh_cb = 0, qm_secret_key_cb = 0, qm_encrypt_cb = 0

View 1 Replies View Related

Cisco VPN :: Setup A Remote Access VPN On ASA5505 Firewall

Jun 2, 2013

I have setup a Remote access VPN on my ASA5505 firewall through the ASDM wizard.I can successfully connect with the Cisco VPN client. My firewall also shows me the VPN session and shows incoming Rx packets. However, Tx packets remain 0, so no traffic is going out. My ASA5505 is configured as router on a stick with 25 different VLAN's. I want to restrict traffic to one specific VLAN using a crypto map.When I issue a ping -t command on my connected Windows box, the firewall log shows me the following message:
 
"IKE Initiator unable to find policy: Intf outside, Src: 10.7.11.18, Dst: 172.16.1.1."
 
"This message indicates that the IPSec fast path processed a packet that triggered IKE, but IKE's policy lookup failed. This error could be timing related. The ACLs that triggered IKE might have been deleted before IKE processed the initiation request. This problem will most likely correct itself." [code] I have really no idea what's going on. I have setup a Remote access VPN countless times but this time it shows me the error as described above.

View 5 Replies View Related

Cisco WAN :: Setup New Switch 4506e For Remote Site?

Jun 6, 2010

I'm trying to set up a new switch, a 4506e, for a remote site. Most of our newer remote sites are using a 4506 and this is the first time I'm working with a 4506e. Our standard configuration, which was in use before I started here, has QoS settings. I'm not that familiar with QoS. Most of the QoS commands in our standard config aren't working in the 4506e. Does the 4506e have QoS? Is there some guide as to setting it up? Below are excerpts from the config we're using that are QoS related:
 
qos dblqos map dscp 32 33 34 35 36 37 38 39 to tx-queue 2qos map cos 3 to dscp 26 qos map cos 5 to dscp 46    qos aggregate-policer XYZ_AGG 64 mbps 8 mbyte conform-action transmit exceed-action drop qos!class-map match-all match_XYZ  match access-group 142!policy-map police_XYZ  class match_XYZ police aggregate XYZ_AGG!interface GigabitEthernet4/1 description server qos dscp 48!interface GigabitEthernet4/30  description server  service-policy input police_XYZ!interface GigabitEthernet4/48 description upstream connection qos trust dscp tx-queue 1   shape 98 mbps tx-queue 2   shape 1 mbps tx-queue 3   priority high

View 2 Replies View Related

Remote Desktop Setup - Local Connections Only?

Feb 2, 2011

I have a couple WinXP Pros and Win7s connected to the same router wired and wirelessly. All of them have Remote Desktop enabled (via System settings) and have Windows Firewall exceptions setup. They all have AVG Anti Virus and no other firewalls installed. They all also have static ips assigned.Windows file sharing is working fine between all of them. VNC also works with no problems.But for some reason, I could not get Windows Remote Desktop to work between any of themAnother weird thing that may or may not be related is that they can't ping other computers on the same network.This leads me to believe that this might be a networking issue.I have a DLink router (can't remember model) with a Tomato Firmware.I do not have port forwarding setup for Remote Desktop because I think (although I may be wrong) that they are only used for connecting from the internet, which I don't need. I only want local connections right now.

View 1 Replies View Related

D-Link DIR-655 :: Setup Multiple PCs For Remote Desktop?

Dec 18, 2011

I remember the Virtual Server instead of Port Forwarding can be setup for multiple PCs to be Remote Desktop accessible from the Internet, but I forget how.

View 2 Replies View Related

Setup Linksys 3200 Remote Access

Oct 3, 2012

I'm trying to setup remote access for my linksys 3200 so that I can configure it through the WAN port. I have turned on remote access, however when I try to connect I get a 404 error. The settings I have are:

When I try to access xxx.xxx.xxx.xxx:9999 I just get a 404 error. I have allowed RDP access to a computer behind the router and this works fine on the same IP address. what else I have to do to allow remote management access?

UPDATE: I tried changing the port to 80 and it works. Change it back to any other number and it doesn't work. Modem is setup with a DMZ to the router's IP. Why does it only work on port 80? BTW I can't use port 80 because there is a website hosted behind the router.

View 1 Replies View Related

Cisco :: Asa 5505 - Create A (remote Access Vpn) Setup For Ipsec?

May 8, 2012

I have a newly aquired asa 5505 that I just set up to the bare minimum configurations. I followed a cisco paper on how to create a "remote access vpn" setup for ipsec. I can sucessfully connect and establish a VPN, but when I try to access an inside resource from the vpn address, the asa blocks it.

Specific error is: Code...

View 17 Replies View Related

Cisco VPN :: IPad Remote Access VPN (ipsec) Setup On ASA5540

Jul 9, 2012

I had IPAD setup IPSEC Remote Access VPN to try to conect to ASA5540 and Cat65 VPN service module(V1).I works fine on Cat65 VPN service module using IPAD client, but it is fail on IPAD client connect to ASA5540.THe message should be "VPN server is no response".My laptop Cisco VPN client(Windows 7) works fine on both (Cat65 VPN module and ASA5540).There is any special setting for IPAD client on ASA5540 ? The IPAD ios version 5.1.1.The ASA5540 version 8.4(4)1 ADSM 6.4(9) The Cat65 version is quit old binding with CatOS V12.2 etc.

View 2 Replies View Related

Port Forwarding Setup - Remote Directly Into One Of Servers?

Jan 19, 2012

I have a small network in my garage, it's basically made up of a bunch of test servers. Those and a win xp machine are all hooked up to a switch, and the win xp machine also has a wireless usb stick that is connected to my wireless router, and is being used to share internet to the rest of the machines. The test servers along with the NIC card on my win xp machine sit on a different subnet, however.When I remote into the win xp machine from my house, i can run a second remote desktop in the first session, into any of my servers. I want to do work on them, but its very laggy.

Is there a way I can setup a port either on the win xp machine or my wireless router so that i can remote directly into one of the servers? so if the win xp machine has a wireless ip address of 192.16.13.102, and one of the servers on the 2nd subnet has an internal ip of 192.2.2.4, can i have it so i can make, for instance, 192.16.13.102:6333 forward to 192.2.2.4? If not, is there any other way i can directly remote into one of the servers, by passing the first remote desktop into win xp? What settings would have to be the same across the line?

View 1 Replies View Related

Cisco VPN :: ASA 5505s - Computer Network Connecting To Remote Access Setup

Dec 4, 2012

I am looking up setting a VPN using ASA 5505s so we can connect a mobile network of computers to our base network of computers. The base network has a static public IP address, but the mobile site will not. I was thinking of using a remote access VPN setup, but I am unsure if I can have a network of computers connecting in to the remote access VPN setup.

View 5 Replies View Related

Home Network :: Setup A Remote Desktop Connection For 3 Computers?

Apr 28, 2011

i want to setup a remote desktop connection for 3 computers on the same network to connect to remotely. Originally i was going to port forward the original windows RDP port and run the windows rdp service but learnt that XP Home Edition doesn't support this feature. I want to be able to log onto these computers at any time remotely with the need of accessing the computer before i connect.

View 2 Replies View Related

Linksys Wireless Router :: How To Setup Remote Access With E4200

Aug 11, 2011

how to setup the E4200 so that I can access the media server when I am in office? I was browsing on the Cisco website and unable to find it. 

View 8 Replies View Related

Linksys Wireless Router :: How To Setup Remote Management On A E1200

Aug 25, 2012

I want to be able to login to a router remotely and foward a port on the router. I thought i saw a spot for remote management but don't know how to use it. I have a dyn account and can create a dns for it. 
 
i setup security dvrs on the internet so clients can see cameras from outside their homes. I would like to be able to login to a router if i need to foward a port or something similar. 

View 1 Replies View Related

TP-Link 150Mbps Wireless :: TL-WR740N / Setup DVR For Remote Access?

Dec 5, 2012

Region : Ireland
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :

I am trying to setup my DVR for remote access but my public IP and the routers WAN are not the same?

View 4 Replies View Related

Cisco Routers :: Setup VPN Tunnel Between Linux Machine And RVS4000 At A Remote Site?

Jul 21, 2011

I'm trying to set up a VPN tunnel between a Linux machine and a RVS4000 at a remote site (served via satellite connection). After many efforts, I finally succeeded (based on Openswan). However, while PINGing is OK, big packets (from the RVS4000 LAN to the Linux box) arrive corrupted.
 
I lowered the WAN MTU, with no success. What finally did the trick is to lower the MTU at the RVS4000 LAN interface. Since this is not possible via the Web I/F, I did it via telnet ("ifconfig eth0 mtu 1400"). However, this change is lost after router reboot. How can I make the LAN MTU setting permanent?

View 1 Replies View Related

Cisco Routers :: RV180 To Setup A VPN Tunnel Between Remote Site And Central Office

Aug 18, 2012

I bought 2 RV180 to setup a VPN tunnel between a remote site and central office.The VPN tunnel is established, I can ping from central office to remote site but browsing on that server fails. [code]
 
Seems the routing is not really working through the VPN Tunnel.

View 4 Replies View Related

Cisco Firewall :: ASA 5505 Site-to-Site With UC540 Routing?

Dec 4, 2012

We are setting up a new phone system using the UC540 with a VPN connection between 2 buildings using 2 Cisco ASA 5505's at either end.The problem I am having is getting the phones at the remote site to connect to the UC540 at the main site.
 
Phones/Computers (10.0.1.0/24) -- ASA -------------VPN Tunnel------------- ASA -- UC540 -----------Data Vlan1 (10.0.0.0/24)
|------Voice Vlan100 (10.1.1.0/24)
 
What i am told by UC500 support is that the phones at the remote site will connect if they have connectivity to the TFTP subnet on the UC540, which is 10.1.10.0/30 I added the static route on the ASA and I can ping the 10.1.10.1 TFTP server on the UC540 from the ASA, but not for any other device on the 10.0.0.0/24 network, such as the DC.  I added the static route there and was able to ping, so something in the ASA seems to be preventing it. 
 
I also can't seem to get the ASA at the remote site to ping 10.1.10.1.  I've tried adding the static route there in hopes it would forward it through the VPN tunnel.

View 1 Replies View Related

Cisco VPN :: Can SR520 Do More Than One Crypto Map

Jan 11, 2013

I'm trying to get several VPN tunnels up. It seems that only 1 map can be assigned to the WAN interface (fa4). Is this true or is there an 'extended' map like ACLs?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved