In my test lab I have a CISCO VPN3002 that I would like to connect automatically C1841 after a power down. Unfortunately , when I do the setup , it works and connect directly (3 GREEN LED's).But after a power down , when I look back in the config , I have :
GROUP = 3000client Password=xxxxxxxx Verify=xxxxxxxx
USER = cisco Password= Verify=
Both Password and Verify are empty ?
I own a lynksis wag54g2 wifi router. I can establish wi-fi connection with my Android phone, Iphone 4, notebook, but after I disconnect the device from the router, I can't reconnect it again until I reboot the router. I tried some othe mobile devices with wi-fi support, the problem is the same. I tried set up different wireless security settings, tried to switch wireless mode to b, g, and mixed, installed new firmware 1.00.19, but the problem is not resolved.
View 1 Replies View RelatedI have a remote ASA 5505 running 8.3(2) that establishes a site to site VPN to a central ASA 5520 running 8.4(2) immediately upon startup. Then within a random interval ranging from 5 seconds to an hour, the VPN loses the connection, and is not reconnected. Only a reload of the remote ASA will reestablish the VPN tunnel. Then everything is fine until the next disconnection. Both sides have matching lifetimes, and keep alives are enabled on both sides. The debug from the remote ASA is attached, showing what happens through several disconnect/reload sessions.
View 2 Replies View RelatedI have internet on my computer at home and i have unpluged the computer and moved in to another room it is saying that i need to reconnect the internet.
View 1 Replies View RelatedWhen I connect to the exchange server by using Cisco VPN, microsoft outlook display warning "microsoft try to reconnect ... " many times, at that time I cannot send or receive email, it failed. The VPN still connected so I don't know why? At first I think the problem from MTU so I decrease the MTU but the problem still happens.
View 3 Replies View RelatedI have and D-Link modem which is bridged and a PPPoAPPPoE profile set up on the RV220W for my ADSL2+ connection.I cannot for the life of me find anywhere in the routers config web pages to tell the modem to disconnect or reconnect the connetion to the ISP.The reason I want this is because I need to make sure the correct signaling is sent before the connection is stopped so that the exchange doesnt see this as a drop out and reduce our line speed to compensate.
View 1 Replies View RelatedI have ASA5540 running IOS 8.04-K8, users are able to connect VPN over the internet but unable to re-connect VPN when users disconnected abnormally (abnormally means they are not disconnecting VPN manually, while disconnecting manually no problem occur). ASA showing an active session of the disconnected user and user having reason 433 while re-connecting VPN.
View 11 Replies View RelatedI have a problem with my laptop, it is an HP DV6449us with a broadcom wireless wifi card. My problem is, that my wifi will be working one second, and the next it will disconnect me, and wont let me reconnect! It will show me available connections, and will try to connect, but, fails. Usually happens when waking up from sleep, or using the laptop for long periods of time.
View 19 Replies View RelatedMy Internet will disconnect & then reconnect constantly. I have 2 laptops & they are both on my home network & I have no trouble with the other one so I assume there is nothing wrong with both the Internet service & router. The laptop with the problem is an acer/aspire 5720z. The Wireless Network Adapter is a Atheros AR5007EG. When I go to the Adapter Properties the status reads "The device is working properly". When I go to Control Panel>Network & Sharing Center my Wireless Network Connection Signal Strength reads Excellent. The operating system is Windows Vista Home Premium.
View 5 Replies View RelatediPad connects fine to WiFi leave it idle for 20mins and then when you wake it up, it doesnt reconnect. It is not just this 1 pad, i have about 20 users in the office with same problems.So far i have tried the following:
1. Update router firmware
2. Network initially had split up so each floor router was a DHCP server now only 1 DHCP server.
3. Test with different security WPA/WPA2 and No security.
4. Connect to different wireless router.
5. Try Apple's Airport but doesnt work in corporate enviornment(couldnt even get it working at home)
6. Try adjusting screen brightness (not in a million years is this a fix!!).
7. Static Addressing not an option as too many devices and it is not a fix.
I am in a third world country (Thailand) with ADSL service and getting customer support is difficult to say the least.The connection is constantly dropping but the real problem lies in that i can not reconnect unless i restart my computer.
View 8 Replies View RelatedThe wrt400n works fine. Except randomly every day or every other day, laptops cannot connect to the router. Router lights are still on, blinking, etc, no change there. Releasing/renewing IP doesn't work. Turning off wireless radio on laptop and back on doesn't work.Unplugging and replugging in the router DOES work, and laptops can connect to the router again.Router is updated to 1.0.02 firmware, sine I thought that was the problem, but after firmware update, problem is still occurring.Wireless is set to mixed,channel width is auto?
View 14 Replies View RelatedI kinda accidentally disabled our internet network and I can't find a way to reconnect it with our adapter. I tried to troubleshoot it and also search for our device, and nothing seems to work.
View 8 Replies View RelatedWhen doing anything on my PC, gaming, browsing, whatever, I will have random disconnects for a few seconds and it will reconnect. I don't get the "your network cable has been unplugged" message, it just stops working for a second or two and starts working again. This has been happening for a few months after a fresh install of windows xp and I haven't really tried to fix it.Every other computer in the house is fine except this one, it can't be the modem because a new one was installed a few days ago and its the same problem. The router was reset within the last week as well. I think the problem is with this computer alone but I don't know where to look. The problem didn't happen for a few days after I put a new network card in, but soon after it continued happening. I also have tried a few different CAT5 cables, even the XBOX one but nothing resolved the issue.
View 4 Replies View RelatedHow to reconnect to Wi-Fi network automatically
View 1 Replies View RelatedI have a WLC 5508 in my datacenter, and 1142s configured with FlexConnect at a remote site.Two issues:Some APs 'die' from time to time where I cannot ping them anymore and they do not service any clients. I can reset them from the WLC after which they work again. I have some clients in the building (same area) who lose connectivity from time to time and are unable to reconnect to the wireless. I am seeing errors that the gateway cannot be found or there is not a valid IP. restarting the AP closest to the clients fixes the issue. I have replaced the AP and connected to a different port on the switch.
View 6 Replies View RelatedI am working with a small off that has a 5505 acting as a basic firewall. Behind it are off-the-shelf unmanaged switches. Two users have to work with an outside vendor and are having issues. They have a Sonicwall remote VPN client on each of their desktops and use this to connect to the vendor. They then RDP into VMWare-based Windows 7 desktops at the vendor's site to do their work. Randomly throughout the day (6-10 times per day) while they are actively working the RDP session will disconnect. It will auto-reconnect after a few seconds. The VPN log on the clients never show any issues. I believe this is an RDP problem because while the RDP session is disconnecting, their VPN client is not (it is set to NOT auto-reconnect if it gets disconnected so that I will know for sure if it gets disconnected). I don't see anything in the ASA's logs about denying connections involving their PCs and the remote VPN peer IP.
View 7 Replies View RelatedI have a new 881 router and am simply trying to change the ip address from the default 10.10.10.1 to 192.168.15.1
I tried doing this both in the CCP Express app loaded on the router, and also using the desktop CCP client. I can change other parameters without any problems, but when I change the ip address of the vlan the program hangs (as expected since the ip address should be changing). I then try to open it back up and reconnect but get no response from the router.
I can ping it no problem, and the http server is running according to the serial terminal.
I used to have ATT DSL but we recently switched to U-Verse. I have a Trendnet TEW-452BRP 54g wireless router than was handling the PPPoE function. It was set to work flawlessly with my wireless cards. No dropped connections, speed or security issues. It always connected quickly from wake up and on start up. Now we have a 2Wire i38HG wireless router/gateway and it's been difficult to properly set my network up as before. I use the Trendnet behind the 2Wire as my wireless router. Took me a while to figure out what to do, but DHCP is disabled on Trendnet so 2Wire does what it needs to. This option works fine for me. The only problem is that at first my wireless card would not automatically connect to the network through the Trendnet when it is in range like I had it set to do previously. When I would force it to, after 3 times it would magically connect on it's own. I made some changes in the Trendnet (Mainly disabling dynamic DNS and NAT) and that seems to have made a difference. To be honest, I don't know if that is significant or not or if it actually made a longterm difference but it seems like it has. So my problem is now that when I put my laptop to sleep and have it wake up, it does not automatically reconnect. It takes about 2 minutes then it does on its own. I read the event viewer and this is the info it gave me - Your computer was not able to renew its address from the network (from the DHCP Server) for the Network Card with network address 0x0018DE0682D8. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server.
Level - Warning
OpCode - IpLeaseRenewalFailed
Source - Dhcp-Client
Then after 2 minutes -
Your computer was not assigned an address from the network (by the DHCP Server) for the Network Card with network address 0x0018DE0682D8. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server.
Level - Error
OpCode - IpAddressNotAssigned
Source - Dhcp-Client
After this, it connects by itself. I don't believe I have configured the 2Wire or Trendnet properly, so I need some guidance and suggestions on this matter.
Laptop - Intel Core Duo 1.66ghz, 2gb Ram, Win7 Professional with SP1, Intel PRO Wireless 3945ABG
2Wire - 192.168.1.254
Trendnet - 192.168.1.1
- I did not change the IP of the Trendnet and I am not sure if I have to.
From the 2wire - Private Network
Router/Gateway Address192.168.1.254
Subnet Mask255.255.255.0
Private Network DHCP Info
Range192.168.1.64 � 192.168.1.253
[code]....
Cannot reconnect to the internet after reinstalling Windows XP SP2 on HP DC7100 SFF. Internet connection is via switch to modem to cable. Working fine previously, and other computer connected to switch still working fine?
View 7 Replies View RelatedI work for a small company and we just brought in a Juniper EX4200 switch so that we are able to test our SFP's and XFP's. I went through the EZSetup process however when I try to re-connect afterwards it just tells me that my subnet for the switch is different then the PC. I have tried assigning a static IP but that is not working for me either
View 8 Replies View RelatedI have a red x in "My Computer" at the network drive. cannot connect to it. what do you suggest. I am on a pere tp pere network
View 1 Replies View RelatedI accidently disconnected my wireless adapter, how do i reconnect.
View 1 Replies View RelatedMy sony blue ray player lost it's connection to my wireless lnyskis router. I can't reconnect it.
View 3 Replies View RelatedI'm using two WRV210 Linksys Cisco Routers to create a tunnel between two places with a pppoe adsl internet connection.I made several tests with new 2.xxx and old 1.7xx firmware, and nothing changes.Try to reset to factory defaults, and nothing changes.I have two problems:
1) The router crashes after a time working, usualy around 24 hours, sometimes more, sometimes less. The lights still flashing, but nothing happens, no VPN traffic and no ping response from the router, and of course, no internet access. I could see just that the router works a bit hot, but, I think that is normal.
2) The VPN IPSEC was configured, and both configurations are identical. All value are the same, I am using the dyndns service. So, the VPN quickly connects and I can ping and access remote computers. Windows Folders, VNC, IT'S REALLY WORKS FULL. WORKS REALLY FINE. PERFECT.
BUT, when the router crashes, as I've told on problem 01, after remove the power cord and insert ir again, the VPN don't reconnect.On log's, I could see that it's say that has no preshared key. [code] But, it worked before. Nothing changes, nothing, the router just restarts. No configuration was lost, (I checked the VPN IPSEC TAB), but says that have no preshared key,The unique way to restablish the connection is go on the VPN IPSEC TAB, and change symetrical any configuration, as change MAIN MODE to AGGRESSIVE on both routers.So, now are as MAIN. Tomorow probably it will crash, so, I will have to restart both routers, and change to AGGRESSIVE. So, when it happens again, i will have to back to MAIN.
We have a WAP4410N wireless ap configured for WPA2-Enterprise. Initially everything works. Issue the user the proper certificate and they sign on correctly but once they disconnect and try to reconnect later it get stuck on "Validating Identity". The request never get to RADIUS server (no success/failure log entry, no radius traffic). Once I reboot the access point everyone can connect again but as soon as they disconnect the problem happen again.We testing other security settings (WPA-ENT, RADIUS(!), WPA2-Personal etc) and no problems. With older firmware have the same issue.Operating system: XP SP3, RADIUS server: IAS. Firmware: 2.0.1.0
View 2 Replies View Relatedwent to uninstall the other two and then went to install our new one on the main computer.I have now lost connection with the wifi to this pc and only this one. (the internet still works on two laptops) unfortunately i need this computer for work and therefore need the internet quite urgently. Perhaps uninstalled something by accident and if so what is it and what can i download?
View 3 Replies View Relatedwin xp I work at a junior high school. A lot of the computers are part of a work group so they can share printers.
I'm having problems connecting to a printer. It has worked for a long time, it's still my default printer, but when I try to access it, it gives me a spooling error.
Now here's why I think it's a network problem.I can't access the main computer's network location (the one hooked up directly to the printer). All the other computers come up on the networkjust fine. And the one in question is only able to access very few computers in the network browser. let me simplify:
computer A/ brother printershared computer B/no longer sees A on network A/ sees only a small portion of other computers on network B/ sees all computers but A
Again, I don't think it's a spooler problem. It probably gives that error because it's a default printer with a lost connection.
windows was unable to connect dlink (router) is message i receive on my laptop after setting my son's nintendo 3ds to the wifi connection. internet connection is otherwise fine on other devices in home.
View 1 Replies View RelatedI purchased the Netgear a couple of years ago and it worked great. Since I've upgraded to a faster bandwith from Verizon, I can't get the Netgear to work. What am I not doing?
View 1 Replies View RelatedNetgear WGR614v7 Router.I have three computers wi-fi networked via the Netgear router: a laptop, a Mac Mini, and a XBox 360.About 30% of the time, when I wake my laptop up, it's been dropped from the network. The only thing that seems to allow it to connect again is if I unplug the power from the router and plug it back in again.This also happens to the XBox 360 once and a while. It never happens to the Mini. I suspect the Mini never gets dropped because it never gets turned off or goes to sleep.Some things I've tried to no avail:
- restarting my laptop
- manually reconnecting to the network via the icon in the system tray
- ipconfig /release, /renew
- disabling power management on my network adapter
- updating my router's firmware
My research keeps pointing to my router's "idle timeout" setting, though that may or may not actually be the problem. In my router setup, I currently have the "Does Your Internet Connection Require A Login?" setting set to No. When it's set to No, I do not have access to my Idle Timeout setting. If I set Login Required to Yes, I do have access to Idle Timeout, but none of my computers can connect, and I'm unsure how to get that working properly. I've read that if I set Idle Timeout to 0 (zero), it essentially never times out.
I will be setting up a new computer this weekend. I presently have a WRT54G2 wireless-G router and have configured it to an IP address that works with my AT&T(Bellsouth) broadband modem (Westell). When I reconnect it to my new computer, should I first just connect the ethernet cable to the modem as if I don't have a router (like I did for years) and then go into the instructions for setting up the router via the DVD but enter the IP address as I have it working now?
View 3 Replies View Relatedi have a wrt160Nv3 wireless router.
I had a wireless device connecting to my network - so I blocked it. Unfortunaletly turned out to be my daughters ipod touch. How can i reconnect it back. dont seem to be able to add device and linksys keeps blocking her connection attempts