We seem to be having an issue with one of our 4500's, our standby supervisor is continuously rebooting: [code]
I have replaced the supervisor board but the issue still persists. [Code] ......
I'm having a trouble with a 4510R+E switch. The WS-X45-SUP7-E supervisors are constantly rebooting, and we can see a 'critical software exception reload' reason. We have checked the logs
______ uptime is 5 weeks, 1 day, 19 hours, 3 minutes
Uptime for this control processor is 37 minutes
System returned to ROM by reload
[Code]....
What can we do to solve this incident?. Everything was working fine, and suddently the problem arose.
I have issue with my 4510 switch which has got two supervisor engine in single switch.
I am trying find the root cause but not able to ....
Standy supervisor engine is not detecting ....
In show module and bootvar output also , there is error saying " Standby is not up "
show module ouput :
Switch-4510#show moduleChassis Type : WS-C4510RPower consumed by backplane : 40 WattsMod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 6 Sup V-10GE 10GE (X2),
[Code].....
I went through the configuration guide for 4500 series switches for NSF/SSO for failover between Sup's. I just wanted to know that that are we supposed to run the SSO command on both of the supervisors? Secondly, are we only supposed to run the nsf process under EIGRP on the secondary supervisor and routing peers and not on the primary supervisor?
View 2 Replies View RelatedI have 3845 Router which is continuously rebooting; console output is attached.
View 8 Replies View RelatedMy VMware virtual machine running Prime Infrastructure 1.2 is continiously rebooting.VM console is generating logs as shown below.
View 1 Replies View Relatedwe got 2 Cisco 4005 Switches with IOS 12.x. t.Now we have two new Cisco 4500 Switches with Supervisor 6E-L.But i dont really understand the new syntax / configuration method of ios 15.
View 2 Replies View RelatedWhen i have configured the 4507R switch but the configure is not sync with the standby module..... I have doing some troubleshooting
1. type the command "show redundancy" no standby module is showing
2. type the command " redundancy force-switchover" showing the message " no standby module is present"
3. type the command "hw-module module 2 reset" then the standby module is reset and status light is blinking like it is booting..
I just bought an EA-4500 and i am having problems with rebooting the device. Every time I change a setting and the router reboots it never starts up again - and the logo LED doesn't flash, it is on constant. I have to cut the power and wait for about 15 minutes, and then it boots up fine - logo flashing and all.
View 5 Replies View RelatedWe are expanding out LAN network with more 2960 access switches. All the access switches are suppose to be connected to core switch (4507R) but i have less port on the core switch.
On the core switch we have two supervisor engines (WS-X4515 ---description : "Supervisor IV with 2 1000BaseX GBIC ports"). I can see that on each supervisor engine i have two 1 GB SFP ports available and if i calculate for two supervioser engine i will have 4 1GB ports.
But at particular time only one supervisor engine is active and other is in standby mode (redundancy mode used is SSO between two SUP engines).
Can i used all 4 SFP ports for connecting 4 uplinks to the 4 access switch?Will all the 4 SFP ports active at one time or only 2 SFP ports will be active that is for only active supervisor engine.
I was upgrading IOS on 4507 R with dual supervisor.I download the IOS on Active supervisior and did reboot.After reboot i login to switch then i got switch standby prompt.I found that after reboot active supervisior became standby supervisior.
Now new IOS is on standby supervisior.Need to confirm below..So this means that IOS does not syn within the supervisiors as compared to config right ?
-Which command i can use that will copy IOS from standby supe to Active supe??
-Which command i can use that will show both active and standby supe with new IOS?
-Is there any command that i can use to switchover from active to standby supe??
I have a strange issue with 4500 E chassis loaded with SUP 7L-E which always remains in ORANGE LED status, also the uplink ports interface is down and the line protocol is down but when i execute the command sh int gig1/5 it show me the media type sfp but there is no red laser light seen in the sfp transiever,The below command is configured for the uplink gig port on the SUP engine.hw-module uplink select gigabitethernet?
View 10 Replies View RelatedI have a 4510R-E chassis which currently has a single supervisor 5 installed.
We are now looking at upgrading the supervisor to a Sup6. Now the question is this, can I install the Sup6 into the redundant cpu slot and then perform a failover to get the new switch working without any noticable downtime.
I'm not sure what having a Sup V and a Sup 6 in at the same time will do to the backplane.
Otherwise I have to take the switch down and then install the card and software manually.
I am trying to understand the implicit limit to the priority queue. I know you can define an explicit policer but if you don't I can't find out what the rate limit really is.
View 5 Replies View RelatedWe bought Cisco sup engine WS-SUP32-GE-3B for 6500 switches 2 nos for redundancy. I have connected 6 systems on each sup engine ports. How to clarify whether both sup engine will forward the data while one is Master and other is standby?
View 4 Replies View RelatedOn an existing 4500 switch with a single sup 6-E, another sup 6-E is added. But the second sup6-E comes up as synchronised with active and in a few minutes time, reloads again. the software is 12.2(44) is the same on both sup engines. the redundancy sso output shows that slot6 is disabled.
View 1 Replies View RelatedOur company will go to buy a core switch 4503. What is the difference between the Catalyst 4500 E-Series Supervisor 7L-E and the Catalyst 4500 E-Series Supervisor 7-E?
View 1 Replies View RelatedDoes a new Cisco Catalyst 4500 series supervisor 7L-E model WS-X45-SUP7L-E is backward compatible with a Cisco Catalyst 4500 series chassis model 4507R? I've checked on Cisco website for that Supervisor and it shows only new chassis models WS-C4507R+E and R-E, but what about old type of chassis? We need to upgrade that Supervisor as it's out of line, but we don't really want to buy a new chassis as well as it's going to be very pricy.
View 6 Replies View Relatedswitch catalyst 4500 with ios cat4500e-universal.SPA.03.02.00.XO.150-2.XO.bin. I need to configure modules 3 and 4 of supervision, the problem is that I need the 4-port module 3 are active but only the first turn on both the module 3 and the first port on the module 4. [code]
View 1 Replies View RelatedI know in the past on earlier models of the supervisors that you couldn't use all eight uplink ports(4 on each supervisor) simultaneously when you have two supervisors on the chassis. Is this the same case for the 10Gb uplinks on the supervisor 7-E on the 4500 chassis? I tried doing my research but couldn't find an answer.
View 3 Replies View RelatedI have a Cisco 4500 as my core switch and there are two sup eng in this core. However, I noticed that the redundant sup is in diable mode rather than Hot Standby.
I have tired to enable the module but I am not able to do that.
The sup of my core is: WS-X45-SUP6L-E
last night I started upgrading our ASA5520 active/standby cluster. Because of lack of memory, I stopped the upgrade process and will continue when the memory modules have arrived... Currently I'm running 8.0(5) on both nodes (Version: Ours 8.0(5), Mate 8.0(5))Whenever I use the "write standby" command on the active ASA, the passive ASA seems to drop it links for a short while. [code]
View 4 Replies View RelatedOur internet has been acting strange the last couple days, it will just disconnected for like 5-10 seconds, then come back. Happens anywhere between every couple minutes or every 15-30 seconds. There are two computers on the network, and it happens to both computers at the exact same time.
View 3 Replies View RelatedRouter with 2 RSP RSP720-3C-GE & Image: c7600rsp72043-advipservicesk9-mz.122-33.SRE2.bin We are getting the message as
------------------ show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRE2, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code]....
Show log is attached & we are getting %DHCPD-4-DECLINE_CONFLICT: messages constantly.
I've got a brand new C887VA-W-E-K9 that is up and running on a BT VDSL connection. That side of it is fine... But the integrated AP module on it keeps reloading.. I can be on the AP console reading the config via 'sh run' and suddenly it'll be loading the OS again... There's no errors logged, no errors on the console or anything... (I also have yet to get the radio working, it starte dbefore I'd finished the config).
It doesn't seem to be anything I'm doing as if I just leave the console, it'll just sit there... reloading every few minutes... (Although sometimes it seems to stay up for longer).
The console just looks like this. WHich is taken from listing the running config and while sitting at the --more-- prompt... Bang...
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
[Code].....
Happens every few hours, but is fixed by reconnecting my router. Although this is inconvenient because I run an IRC chat and a small web server. I'm not sure if those would cause such a problem, but I hope not
View 14 Replies View RelatedI getting continuously BGP notification error.We are using the cisco 1941 router. i have attached error and configuration.
View 1 Replies View RelatedI have got a cisco 1841 router. i can't see anything when connected to hyper terminal application. I can't ping to any interface of the router. The CF and AIM lights are glowing continuously and every light also glows near FA interface when cable connected on the interfaces.
View 1 Replies View RelatedI have recently moved in a new apartment. At the building there is something like a centralized internet. There is a huge machine which is connected to every apartment of building via a cable modem(Netsys nh-300sp). Here is an image of system. And when I first came to apartment they gave me a username and password which I made login when i firstly opened a page on safari. When I plug in an ethernet cable to my macbook-air it connects and everything s good for a moment then it starts to kick me out randomly and continuously. When I look to Network Diagnostics: ISP is red, internet and network are yellow.I tried also using a manual DHPC address, but then ISP is green but Internet and server are red or yellow. I cant even reach to modems admin panel, maybe because of the system of building.
View 1 Replies View Relatedmy internet will disconnect sometimes for a split second, for a few minutes or for hours at a time. My boyfriend and I have directly connected his computer to the modem, and the internet is working. I have also called our ISP and asked if there are any problems on their end, and our modem is working fine with no issues. So we had come to the conclusion that our router was at fault. It was a Linksys E1500, we investigated online and found that many people had the same problem and it was solved through buying a new router. We have since bought a new router a D-link N150, it worked for a week and a half, but now our internet is back to disconnecting randomly throughout the day. We have tried resetting the router back to factory settings to an avail.
View 1 Replies View RelatedMy nephew's MAC continuously times out when trying to connect to my wireless connection. Details are:
ISP=Orcon
Modem/router=Dynalink: RTA1025WE
No other network equipment.
Wireless connection
Authentication=WPA-PSK
Browser=Firefox
MAC Book Pro, OS=10.6.2
one of our 2 ACE boxes in FT group suddenly reboot-ed from active state and now it continuously reboots with the following error:
insmod: error inserting '/isan/bin/klm_octeon_device.klm': -1 No such deviceerror inserting /isan/bin/klm_octeon_device.klmDaughter Card Not Found. Rebooting..INIT: Sending all processes the TERM signal...
My internet connection is continuously transmitting and receiving, even when there is no application running! is there any way to find out what is being transmitted or received and how to reset the connection?
View 3 Replies View Related