I want to get a Cisco router for central point of 100 GRE tunnels and total 10G traffic coming from those tunnels. I used 6500 but its CPU became high in less than 2 G traffic. Can you identify me a suitable router for this purpose. I think the router must process the GRE in hardware.
View 8 RepliesI'm looking for a device which will allow me to forward all internet bound traffic through a L2L IPSec tunnel from branches to a central hub and internet connection.
I've recently purchased a RV120W(as a test branch device) which i've tried to get working with the ASA5505 at the central site. I can get the VPN to come up but can't manage to get the internet bound traffic through it. Reading up on the issue, it looks like full tunneling or IPsec wildcard forwarding isn't supported on the RV120W and RV220W devices [URL] The source mentions that the RV0xx series supports this feature, however one of my requirements is wireless on the device.
Any device which supports this rather than just the standard split tunneling, alternatively a workaround which will allow me to use RV120Ws at branch sites? Would an SRP521 support what i'm trying to achieve?
I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
My comany is planning get full bgp table from our providers we have mutliple egress providers in order to load balance we are looking for a full table from all of them what would be minumu requiremts we have all edges as 6500 with sup 720 ,is there any memory requrements that need to be upgraded ??
View 4 Replies View Relatedwe need to relocate our core switch 6500 with sup 720 to another bldg
what is the command to gracefully shut it down I mean power off
I was told one can just switch off the power
We have two 6500s. One is running in power redundant mode and the other is running in combined mode.We need to change the one running in combined mode to redundant mode to ensure it can run ok on one supply if needed but I have a couple of questions.
1. Assuming that we are not oversubscribed on the power allocated, does changing the mode cause any disruption?
2. The switch running in combined mode seems to have allocated some power for an "Inline Local-Pwr-Pool" which is not allocated on the switch running in redundant mode (see attached). Does this allocation will be needed if we change the power mode?
I have 6500 core switch with 2500W power supply, and I want to install a second power supply with 3000W ? is this applicable ? if yes, is there a specific configuration that must be done ?
View 4 Replies View RelatedI know that the 6500 with a Sup 720 reserves power for a redundant 720. If there is no plan to install that redundant Sup, is there a means of releasing that reserved power? I know that one approach would be to insert a card into that slot to cut the reserve down, but I need to reclaim all of that power.
View 10 Replies View RelatedWe are having troubles getting a 10Gig interface to come up with a carrier... it shows down down.We are using X2-10GB-LR on a 6500 and SM fiber, distance to carrier hand off is about 90 feet.
According to: [URL]
The receiver power on a X2-10GB-LRis
Max
0.5
Min
-14.4
Our carrier is sending at +5db. Currently the interface is down.
My question is; would the interface even come up if it is receiving a powerful signal?
Here is DOM output for our interface.
show interfaces transceiver detail
Optical High Alarm High Warn Low Warn Low Alarm
Transmit Power Threshold Threshold Threshold Threshold
Port (dBm) (dBm) (dBm) (dBm) (dBm)
[Code]....
Cisco IP phones attached to a Moduke in one of my Cat6500 access Switches suddenly went down. Upon closer inspection of the Switch Sys log, I observed the following Sys log error messages: [Module 9 is experiencing the following error: Inline Power Module - PS Voltage bad. ]A sh Mod output indicates the PoE daughter card and Main Module are "ok" - see attached output. It appears issue is related to the the actual Power Supply module and not the blade module and installed PoE Daughter card. I am inclined to open a TAC case for a PS replacement, but wanted to see if this can be resolved without a hardware replacement. At this time all 48 IP phones attached to this module are out of Service.
View 2 Replies View RelatedThe following discussion is based on cisco cat 6500 switches with two power supplies: p1 and p2. . Both power supplies are running in combined mode .Each power supplies is rated with 500 watts max( I just picked 500 watts for simplicity)Combined mode In combined mode, each power supply provides approximately 83% of its capacity to the chassis. This allows for greater utilization of the power supplies and potentially increased PoE densities
1) Let say our specific 6500 switch's configuration requires 1000 watts. We have two power supplies p1 and p2 ,each with rated power of 500 watts. Both power supplies must operate in combined mode. Will power supplies be able to meet the total load power requirement of 1000 watts?
Here is my understanding :The maximum power delivered by each power supplies is 83 percent of its rated power, assuming power supplies are running in combined mode.
So Maximum power delivered by power supplies
= 83% of p1+ 83% of p2
= 83% of 500 + 83% of 500
= 415 +415
=830 watts
Thus the required load of 1000 watts can not be met by our power supplies in combined mode.
2 )Suppose our switch's switch configuration needs 500 watts. Again our power supplies each rated with 500 watts, are configured for combined mode. How much power is being delivered by each power supply? Is it 83 percent of the total load i.e 500 watts?
can I plug power supply from 4500 to 6500? more specifically we have power supply PWR-C45-1300ACV. And we need to place some power supply to 6500, which has only one active module. So 1300 should be enough for it. But we dont know if they are physically compatible, if it is possible to plug. I didnt find this power supply to be officially?
View 4 Replies View RelatedI am getting the below messages on my Cisco 6500 series switches every 1min. The IOS version is 12.2(33)SXI6 & with SUP32-GE-3B
%ILPOWER-7-DETECT: Interface Fa1/1: Power Device detected: Cisco PD
%ILPOWER-7-DETECT: Interface Fa1/1: Power Device detected: Cisco PD
%ILPOWER-7-DETECT: Interface Fa1/1: Power Device detected: Cisco PD
These messages are I am recieving on few ports only not on all port having IP Phone connected. I tried changing the phone to some other model but that also did not resolved my problem. Also I tried powering on the phone using power adapter but the issue still persist.
Client are not facing any issues due to this error, but still I would like know what can be the issue which is generating these logs.
3 different sites which are directly/indirectly connected to cisco VPN router RV042 and we want to make a vpn between them, how can we make it
View 2 Replies View RelatedWe have a router 2911 recently purchased which supports vpn but we are not able to do vpn tunneling, So what is required to use VPN connection.
Does ios has to upgrade or some kind of license is required.If license is required then what kind of license.Router version is 15.0(1r) M15 which I found in sh version command.
I'm using a Netgear WGT624 Router for my firm's intranet. At home I'm using a router called NSW-R2 by Gembird..
What I want to do is connecting my PC at home (Windows XP) to my firm's intranet so I can print on my LAN Printer or edit files on my NAS.
I've heard about VPN tunnels, but I don't want to keep my firm PC on 24 hours a day. So is it somehow possible, to build a VPN or something similar by only using the Netgear WGT624 Router?
Edit/More Information: I've steup a DDNS. My Router supports Port-Forwarding. I'm currently using Remote Desktop. Both PC run Windows XP Professional.
my router has been checked and is receiving 8mb download speed but laptop, pc & xbox are only receiving less than 1mb speed
View 1 Replies View RelatedI am currently connected to my router via a 100 megabit cable (the router port itself is either 100M or 1G, I can't remember). There are no free ports on the router, but I want to connect additional computers to the network. If I get a gigabit switch and connect two of my PCs to it using gigabit cable, can they communicate at gigabit speeds, or will they be limited by the 100M connection back to the router? (In other words, does traffic between two computers on the switch have to be sent through the router, or not?)
View 2 Replies View RelatedI just got a new E4500 and plugged a blank 2TB drive into it (Windows shows it is formatted NTFS) which was originally plugged into my WRT-610. I'm moving my media files and when it hits a 50+GB video it reports that there is not enough space to move the file. Smaller files are moving just fine.
View 4 Replies View RelatedI just bought a E1200 routerand using automatic setup by using CISCO connectafter that, I only got a CONNECT SPEED with about 10Mbps in my android smart phone,I would like to know how can I increase the WIFI strength WITHIN THE WIFI SETTING, I chose MIXED mode rather than specific in b/g/n mode.
View 4 Replies View Relatedmy router has all the lights on that it's always had. I use the wi fi for my iPhone,iPod, and laptop. On all of then I'm able to to search and find my connection and connect to it , but it's shows I'm connected with full signal but my internt just worn work . I can't connect to the internt on none of the devices, also if I connect the ethernet from my modem to my router then my routers ethernet to my pc my pc's internt won't work.
View 2 Replies View RelatedI have a 100mb conection and regularly get 90mb plus speed when conected direct to the modem. If I conect via the E4200 I only get 50mb ? I have tried disabling the firewall and QOS but this has had no effect. I am using a wired conection and the latest firmware. Its almost as the E4200 is capped at 50mb throughput.
View 6 Replies View RelatedI recently bought an AE1000 wireless adaptor, but I have run into a problem.The range on the device is very low, as the only way to get full signal is when the router and device are right next to each other.I have read that this could be due to the device operating on 5.0Ghz frequency, and that this setting is changed through the Cisco Connect software. This software was not in the Setup CD, and the online installer did not install the software either.
View 4 Replies View Relatedi have a little annoying problem with my E4200. V1 with the latest 04 fw. It seems, that after many hours of downloading at full speed (only one torrent at a time) the speed goes down, and up again, and becoming unstable. My max download speed is 1.5 Mb/s, and it can drop from that, to 50 kb/s, and then up again. and i have no internet access when that happens, but it only last 10-20 seconds and then its back again. Sometimes i get that yellow warning sign on the taskbar which says "No Internet Access" but not always.
Seems like its happening after many hours of downloading at full speed. im on the latest firmware, have tried different channels, 20 Mhz only on Channel Width, different names on the 2.4Ghz and 5Ghz channels.. i use the 2.4Ghz channel btw. Otherwise its stable, and i have had no problems while gaming online.
I have an EA3500, I have 30 Mbps download when I connect my pc directly to the modem. When I add in the EA3500 router it drops to only 10 Mbps download on both wired and wireless devices.
View 9 Replies View RelatedI just acquired a used E2100 from an auction, when I plug it in I see an "Unnamed Network" with full bars in wireless, but can't connect since I don't know the ssid/password.When connecting with cable, with ipconfig I get a 10.10.10.108 ip, the gateway is at 10.10.10.99. Yet I also cannot access it.I have tried the reset button at the bottom, holding it for over a minute, pressing it quickly, holding it for 30 seconds, holding it and unplugging + replugging the router, but nothing is working.I have also tried the CD that comes with it with cable and with wifi only, but it does not find the router. I have deleted my default wireless network settings, had my wifi on, was not connected to any networks, yet the CD could not find the router.When router is on, the WIFI led blinks around once a second, while the LAN led blinks randomly like it should.
View 3 Replies View RelatedI am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
I keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.
We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
how can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies View RelatedIn a stand alone 3750x switch configuration, can the secondary power supply only act as a redundant power supply (active/standby), or can it become a "pool" of power similar to power sharing mode for StackPower (somewhat active/active)? I understand there is no stack involved here but I'm curious if this functionality is possible.
View 1 Replies View Relatedhow can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 5 Replies View Related