I've configured an static route in the ASR1001 router with a name with it eg: ip route 172.20.x.x 255.255.0.0 172.20.x.x 255.255.0.0 name To_system_X.i want to change the name without removing the route.
View 2 RepliesI have pix firewall 525, configured with ospf process. We are also performing route filetering in ospf process using route-map. Now we want to remove this route-map from ospf process. Any step-by-step process for removing route map as per below list. How to remove route-map without having any impact as per above configuration.
View 1 Replies View Relatedi need to know if the built-in GE ports in ASR1001 or ASR 1002 (-X) have the features of QoS without restrictions, or QoS features are supported in SPA modlue ports only?
View 2 Replies View Relateda) one router with two ethernet interfaces (LANs) and a serial interface. The serial interface is connected to the internet, dynamic nat is used for hosts in the two lans. A web server has a private address of 172.168.50.10 and it is being translated to the internet with serial's interface 68.32.x.x (public ip) with static nat. Clients in the internet type the public address to access the web server.
b)Problem: clients inside the LANs cannot access the web server by typing the public address, they use the server's private address instead, this create a problem with DNS static entries in the HOSTS file in the OS. It is a test server and is only available to authenticated users (lock and key ACLs), so no need to make a real DNS record. The entry in the HOSTS file points to the public address.
c)Question: how can a create a route map to change the public address in the HOST file to the private address of the test web server everytime a user in the LANs type the domain name.
I play a game called Unreal tournament 2k4 in online. I am from Bangladesh a small country from south asia. I used to get 150 ping in a Japanese server. But 2 weeks ago my ping suddenly rise. Now its around 268-320 in same server. But i have 160 ping in another Japanese server. So i used trace-route option from avast IS to check the route of my connection.I found out that the server i am having high ping connects through Italy then to Japanese server. But the server i have low ping goes to Singapore then to Japan.My question is can i change the route of my connection so my first server doesn't take the route of Italy?
View 1 Replies View RelatedWe are using a CISCO1921-SEC (ISR) with IOS 15.1 and we configured a "crypto isakmp client configuration group". We can connect with the "Cisco System VPN Client Version 5.0.07.0410" via IPSec/UDP.
1. Is it possible to push routing informations to the System running the VPN Client ? A the moment all traffic is routed to the tunnel but we like only one route to the network permitted with "pool ..." in the "crypto isakmp client configuration group NAME" section.
2. We searched for changing from upd connection to tcp connection via special port. Is it possible with IOS 15.1 on the CISCO1921-SEC ? Is there something possible like "iskamp ipsec-over-tcp port 10000" ?
I have a Cisco router 877. I am trying to configure a backup with ISDN.The primary line is an ADSL over pppoe. The problem is that despite the primary line fails, doesn't change the path and continue going by the main route.I have a very similar setup, also with a cisco 877, but with a normal DSL and it works perfectly.I solved the problem by activating a tracking but is slower than the other method.
View 2 Replies View RelatedDesktop running Windows 7 Home Edition and connected by ethernet cable to a Netgear DG834G v2. Dell Inspiron laptop running Windows XP media edition and connected wirelessly and an iMac connected wirelessly.I did not realise until yesterday that even if I shutdown the desktop I can still connect the laptop and Mac wirelessly. I now want to stop using the present desktop and connect a new desktop with an Epson printer which my wife will use on the other side of the room. I will use the present desktop monitor on this new system. Is it easy to set this up? Also I want to remove Windows 7 from the old desktop and install it on the new desktop, will I have to contact Microsoft to do thie?
View 5 Replies View RelatedMy wireless router is slowing my internet massively. When I am hardwired directly into the modem it has great speed, but when going through the wireless router the speed dropps in half, how can I remove the speed throttle?
View 1 Replies View RelatedMy home computer accesses the Internet through an ADSL modem and a phone line. I added a wired router (Linksys BEFSR41).I've since bought a laptop computer, an iPhone4 and a wireless router (Linksys WRT160N).Again, on the advice of a friend, I ADDED the wireless router, so now have two routers connected.The devices are connected as follows:
-Wall jack to ADSL modem
-ADSL modem to BEFSR41
-BEFSR41 to WRT160N
-WRT160N to desktop computer.
As I understand Linksys routers, the default IP address for ALL Linksys routers is 192.168.1.1.Both the iPhone4 and the laptop are unable to connect to the wireless router.I'm assuming the two routers are conflicting with each other, so I thought I would remove the wired router..Can I change the IP address of the BEFSR41 router from 192.168.1.2?
Would this resolve the conflict between the two routers and allow the wireless devices to "see" the wireless router? What's the correct procedure for removing the BEFSR41 router from the system?
My son gave me an E3000wireless router but the first instruction is to insert the CD and follow instructions. I don't have the CD. How do I install it? Also, this is replacing an older router that is installed and working. Can I install the E3000 without removing the older router first?
View 3 Replies View RelatedI had the 2 circuits go down at the same time from our ISP and I had to power cycle the router and when it came back up I went from VA # 2 to now VA 3#....I know what is what but it is confusing for my counterpart and I can not remove the old entry for VA#1 and VA#2. [code]
View 3 Replies View RelatedThe Cisco E1000 I just purchased provides two connections: a main connection, and one for "guest access." I've successfully disabled the need for password on the main, but the guest access still requires that I assign a password. How do I make this connection open and accessible as well?
View 4 Replies View RelatedI just read the Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series Routers instructions and there was nothing said regading powering down the router. Are these CompactFlash cards hot swappable??
View 2 Replies View Relatedi'm trying to accomplish the following:I want to trasport a bunch of vlan layer 2 etherchannel on a pair of layer3 connections, using L3 to load balance.i was considering a pair of options:
1) bridging + gre (non applicable since i cant bridge 2 interface beloging to a etherchannel to a tunnel)
2) L2TP is it possible to accomplish this with the above tecnology? any reference, configuration example?
3) AoMLPS is it possible to accomplish this with the above tecnology ? any reference, configuration example?
I cant modify topology, the routers used are ASR1001 It is mandatory that both sites have a layer2 connection between them.
I noticed in RME inventory, my ASR1001 hardware is not recognized. I checked my Ciscoworks and it only knows ASR1002, 1004, and 1006 routers.
I checked the supported device table for LMS 3.2 and did not find ASR1001. Is there a separate device package I can download. This is not a deal breaker, but it's unnerving to see the question mark icon next to the name of my router in the Cisco works GUI.
Any document to explain the differences in the Software images for the ASR1001 routers.
View 3 Replies View RelatedWe are looking at buying an ASR1001 but I'm confused by the Licenses and I've struggled to find the information in the cisco data sheets. The router will need to run IPSEC on gre tunnels and I figure that I need the IPSEC license (FLSASR1-IPSEC) do I also require the Advanced IP Services license? or is all that is required the IPSEC license? Is there some sort of list that shows the feature set of each license, they cost the same amount so I'm not sure which license fits what we require best or if we need both.
View 1 Replies View RelatedI want to load balance my Internet traffic between two ASR 1001 routers that are connected to our core switches. Both routers are connected to the same ISP (Comcast) going to the same BGP AS on different /30 subnets. Is there a way for me to load balance my Internet traffic using both connections with BGP rather than having one of these connections sitting idle? If not, the only solution I see is to configure my layer 3 devices to split internet traffic between both routers (i.e. default routes with same AD).
View 6 Replies View RelatedI was doing some research on the Cisco ASR1001 model Router and within the description on the official Cisco page it mentions having various models that come with an "Integrated Daughter Card" or "IDC". I was curious as to what the IDC is exactly, considering there is an ASR1001 model without it.
View 2 Replies View RelatedI've done a similar solution before where I put bandwidth inherit on the Dialer interface of the CPE and it inherited the ATM interface speed (the upload sync rate) and prevented the CPE from maxing out and hitting hardware queuing in the DSLAM. I can't seem to find a way to do this downstream from our ASR1K to the customer though.
Platform is ASR1001 with IOS 3.7.2 or 15.2(4)S
Problem description:We have many xDSL users (ADSL2+ and VDSL2). They all sync at different speeds depending on how far they are from the DSLAM.
Example:
Customer A might be connected at 40000kbps/10000kbps (VDSL2)
Customer B might be connected at 5000kbps/600kbps (ADSL)
When they connect and the PPPoE session comes up, the bandwidth on the Virtual Access Interface is equal to the customer's downstream sync rate, so Customer A's virtual access interface, Virtual-Access 2.13 will say 40000kbps, and Customer B's virtual access interface Virtual-Access 2.39 will say 5000kbps.Using RADIUS, we apply a sub-qos-policy-out to the PPPoE session.I want to shape the customer to 80% of their sync rate so that we do not hit interface congestion in the DSL network which makes VoIP perform poorly.I cannot use an absolute value for the shape, because the sync rate varies for each customer.The problem I have is at present the policy-map is using the interface bandwidth of Gi0/0/1 (1Gbit) instead of the bandwidth of the Virtual Access Interface. Therefore the customer is being limited to 800Mbit which means the QoS policy will never take effect.
RADIUS Config Below:
cisco-avpair += ip:sub-qos-policy-out=QOS-POLICY-OUT-PARENT-DSL
Class Maps
class-map match-any QOS-CLASS-VOIP-RTP-DSL
match protocol rtp audio
match access-group name QOS-VOIP-RTP
class-map match-any QOS-CLASS-VIDEO-RTP-DSL
[code].....
I want to take 100Mb incoming from a service provider and police it off into several VRFs for customers.One of these VRFs will be 30M.I further need to traffic shape this (30Mb) out to 40 x 0.75Mbps (burstable to 30M) customers.
I am using an ASR1001.
Does VPLS is supported on the Cisco ASR1001?With the feature navigator it looks like the ASR1001 is the only ASR1000 series router with VPLS support but I can't find any documentation confirming this.
View 10 Replies View RelatedI have following requirements to implement on cisco asr1001 router.
1.G0/0/0 and G0/0/1 interfaces are connected to a swith through trunk. Multiple customers are will be using this trunk interface . Each customer will have subinterface with dot1q tag.
2 I want both sides of the ASR1001 to be in same segment .
3 If above two is possible I would like to implement shaping on each customers sub-interface level
is above implementation is possible on asr1001. configration and ios information. I found a technology called EVC . but I am not sure is that the one suited for me.
network diagram is attached seperately.
I am suggesting an ASR1001 as a head end router for a small hub spoke WAN consisting of 4 branch sites connecting to the head via LES. 3 are 100mb, one is 30 mb. I will be connecting the LES circuits to a swithc and then trunking to the router. I would like to apply outbound shaping to these 4 subinterfaces on the router, and just want to check this is supported?
View 1 Replies View RelatedI'm trying to upgrade an asr1001 (r1) from asr1001-universal.03.02.00.S.151-1.S.bin to asr1001-universalk9.03.02.00.S.151-1.S.bin. i've put in the boot system flash asr1001-universalk9.03.02.00.S.151-1.S.bin command and reloaded but the box keeps loading first image the configuration register is 0x2102. i've tried the license module command to enable adv enterprise but it made no difference so i removed it again. my license is now;
License Package Information for Module:'asr1001'
Module name Image level Priority Configured Valid license
asr1001 adv enterprise 1 NO adv enterprise adv ip services 2 NO adv ip services ip base 3 NO ip base
To enable netflow export on ASR1001, do i need the firewall feaure license or not ?Docs are not really clear, NBAR requires FW license, but i am unsure about Netflow?
View 1 Replies View RelatedI have been asked what the equivalent of bridge-groups and BVIs is for an ASR1001 and I am struggling to find an example.If we have this IOS configuration:
bridge 1 protocol ieee
bridge 1 route ip
!
interface GigabitEthernet0/1
bridge-group 1
[code]....
What would be the equivalent for an ASR1001 with IOS XE?
I want to copy a file from one ASR1001 and copy it to another. I ntried using tftp 32 but this is not going to work as the image is 315 MB.
how to copy an image from one router directly to another router's flash, if possible?
I have an ASR1001 installed and I want to implement the firewall feature set.The current license level is IPbase and I have the firewall feature installed. The firewall feature shows acive, Not in use. I have tried to activate it without success. My question is: do I need to get a license for advipservices or adventerprise to activate the firewall feature set?
View 5 Replies View RelatedI've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
I am in the process of selling my notebook computer. I did a fresh install of Windows XP and connected to my home router using my WPA security key in order to get the latest updates before selling it. For security sake, I feel I should remove my security key before packaging up the notebook for shipment. I guess my question is, how do I go about removing my security key from the notebook? Or is this not even necessary
View 5 Replies View RelatedI'm donating a computer that was in my office network but would like to delete the office network. How do I do it?
View 2 Replies View Related