Cisco WAN :: Setting Up New PIX 6.3 Getting No Internet
Sep 14, 2011
I am setting up a new PIX 6.3 ,I have a workstation on the inside (192.168.201.10) That workstation can ping the inside interface of the PIX (192.168.201.222) and vise versa.,But my workstation cannot get out to the internet using DNS servers 8.8.8.8 (google dns server),My next hop to the internet is ip address: 173.x.xx.65 255.255.255.224 I am not sure what I am doing wrong.
newblock(config)# sh run
: Saved
:
PIX Version 6.3(5)
interface ethernet0 100full
[Code]....
We just moved to a new place and ISP here have a bit weried connection - they use cable modem that provides "local" IP (through DHCP) to the router and than you have to dial out L2TP to the ISP in order to connect to internet.This setup works fine with "home" routers, like the LinkSys, however I have no clue on how to setup it on 2811.
I'm having trouble setting up a Cisco 2801 as an internet router between our firewall & our ISP.I've setup FastEthernet0/0 as the WAN port & FastEthernet0/1 as the LAN port. I've setup a default gateway pointing the next hop (the ISP),when I plug in a pair of laptops configured to mimic our IP scheme, I'm able to ping thru, but when I put the router between our firewall & ISP I'm not able to get out to the internet (can't ping google) I can still ping the next hop.,Our old router died, so I am unable to pull up its configuration. Here is the code I'm come up with so far.
I have a wireless router in my house and I have a Night Owl video surveillance system setup (hardwired) in my garage and a wireless pc. Is there a way or is there some kind of wireless port device I can get to plug into my Night Owl DVR, so I don’t have to run an RJ45 cable from the house to the garage? I was told by Night Owl tech support the DVR would have to be hardwired only. I would like to monitor the surveillance system from a distance or through a computer.
Configured a D-Link DIR-601 router? The internet is connected, but there is a yellow triangle with a exclamation mark on the bottom right corner stating it isn't connected. I read the manual and did everything as listed, but still have the same issue.
restricting access to internet for roughly 20 users. Right now we are connected using broadbandand using dhcp as assigned by common switch. All pc's are in a common workgroup. recommend me the hardware / software required to restrict this access.
1. Will I require a router as well as a switch ? or should I simply get a new switch ( for more then 20 users ) This would mean static ip for all users.
2. My idea is to create a AD server and use websense on it so that users who require internet access can still open internet sites but will be restricted through websense proxy.
I use a limited usage internet plan and want that when I surf approx 10MB of data my connection automatically stops further download untill i reset or increase the usage.
I have computers A-E in my house connected to the Bright house supplied neatgear cable modem. Computers C,D and E will connect via DHCP. computers A and B have dual NIC's. (10/100 nic A, 1000 nic B). Heres what i would like to do: connect all computers (A-E) to the internet. (this part i am currently doing) on computer A and B i want to create an ad hoc net work to souly use the 1000M nics (for data sharing). I want to separate computer A and B so they wont use the 100 Mbit connection.
I'm trying to portforward for a game, and in order to do so, I'm setting up a static IP. I've portforwarded in the past and all's been fine, but when I'm trying to set a static IP now it allows me to portforward and host the game, but whenever I try to log into any sort of website, it cannot find the page. The only fix to this is to allow it to obtain the IP address automatically. I've had a static IP in the past and yet I've never run into this issue before.
When I go to my TCP/IPV4 settings under the properties of my selected internet connection, I open up my ipconfig(I'll post it below) and select "Use the Following Ip Address". I then input 192.168.1.73, to change it to that.
Then, I click on the subnet mask box and it auto-fills 255.255.255.0, which is listed under ipconfig anyways, and for default gateway I input 192.168.1.1. I leave the DNS server boxes blank because it doesn't list them under ipconfig and it's what I did in the past to achieve the same results. After I click OK, the issue I listed above begins.
Code: Windows IP Configuration Host Name . . . . . . . . . . . . : Tim-PC Primary Dns Suffix . . . . . . . :
Im trying to set up a wireless router in my dorm room. I know, I am not supposed to do that. I got it set up and everything, but still didn't have internet access.
I had so much old garbage and damage from old viruses I needed to reformat the hard drive and reinstall windows xp from the System OS disk. Computer is up and running now, but I lost a lot of stuff, including my ability to connect to the internet and some drivers. I have cable internet. I downloaded Broadcom advanced control suite and the netxtreme 57xx drivers from the Broadcom site, and installed them with the provided download manager. Nothing seems to be working, the control suite says "No active broadcom network adapters detected in this system"....
note- I've been downloading to a different computer and burning the files to CD, and transferring them to the Dell that way...
I need to configure WAP4410N wireless access point for our company guest and visitors.i need them to only surf internet and not to go to LAN (servers).I think i need to create VLAN for this ? can any one tell me setting for configure only to surf internet thru WAP4410N ?
I have large bunglow with 2floors,I would like to have a wireless internet setup in bunglow using 3g usb modem type of internet connection.Advise which router to be used so that I can get good wifi connectivity all over the place so minimum 4 people can use it simaltaneously.
Just moved into apartment in Ann Arbor and am forced to use this ISP. They are not wireless friendly. Their manual sucks and will only provide tech support for $80/hour. I bought a Belkin router and got it working for my MacBook. BUT my roommate can't connect, even tho her MacBook sees the network. And I can't print to my wireless printer even tho it says everything is fine when I run the wireless diagnostics.The ISP has these rules:
- Only connect the router to the Internet or Wan port. Do not connect to the numbered ports (how do I know whether or not I've done that?) - Do not use static IP addresses - Do not run a DHCP server
I have a big 2 floor house .I would like to use 3G connection using USB type of modems,like vodaphone or MTS. which router to be used so that I can get good connectivity on both floors. NOTE- I do not want to use cabled internet coonections.
I built my first computer today (woot!) but I'm having issues using my netgear N300 usb adapter to access the internet.
I am using a DLink router but for some reason I am getting some weird issues.
First of all, after using the netgear usb adapter, my mac address is something like E0-xx-xx-xx-xx-xx with the xx being the other numbers. Is having a macaddress starting with E0 wrong? All the other 5 devices on my router have mac addresses starting with 00.
Secondly, I am getting a 169.xxxxxx ip address. This is really starting to bother me because I can't set it up using DHCP.
I have a Verizon MiFi card and 3 wireless laptops that pick it up automatically.....I can't seem to get it set up on the desktop pc.....it doesn't recognize it
I recently bought a DIR-655 on amazon com, got a good deal. Since I'm old and slo, had issues setting it up, but finally got er dun!I set up a Network all by myself turned on player, did WPS(PBC) on player, and on D-Link. The router and Blu-ray are now friends, however, they are not on speaking terms.Network status on ol Blu- tries to connect then says - Network setting is completed, but cannot connect to the internet, Contact ISP.
just to mess around i reinstalled xp/formatted drive on dimension 4550. plugged ethernet cord from computer to router but can't get any connection to internet. going through the network wizard makes me set up local networks. tried to install new drivers from download page nothing is working.when i open the network connections page under control panel no LAN shows up or anything.
I'm trying to set up a S2S VPN between two ASA5505 SP units running ASA Version 8.2(1). I've ordered additional ADSL2 lines to handle this traffic and I'm having troubles with the configuration for the additional PPPoE connection. Here is are extracts from my current config; First the interface vlans
The result being that I can ping the OUTSIDE interface, but get no reply from the VPN interface. I've checked ADSL lines, they are up. The two PPPoE sessions are logged in and active. I can even see the ICMP packets hit the VPN interface, but there is no reply.
I live in an area that has no cable or dsl internet available.The only options are basic dial up or wireless internet through one of the cell phone companies.Right now I use verizon with a usb adapter.I have had this since moving here.It gets good speed and I share it witht the other 4 pcs in my house through a 5 port switch using windows xp's ics(internet connection sharing)We mainly use the internet for playing games together online.Recently though i have wanted to upgrade to a wireless network.I feel as if I 'm living in the stone age because everyone else I know is using wireless.Last night I went out and purchased a netgear n750 duel band router(model number wndr4000-100nas) after reading several guides online about how to set it up.It sounded easy enough but after 3 hours I still could not get it working.
Here is what I am trying to do.I want to basically turn the router into a switch by disabling it's routing function and let the pc that has the verizon wireless card be the host and hand out ip addresses to the other pcs.(like it is doing now)Problems I am having
1- keep getting the work offline popup when I click on anything in the router control panal(it say you are not connected to the internet would you like to connect or continue to work offline I hit work offline and it just pops up again when I click something else)
2- I think I found how to change the router's ip address and disable DHCP under lan controls but when I hit save it pops up saying I need to manually change my pc's ip address and it will not save.
I am using winxp32 sp3 and right now 5 gigabit wire lan cards.(though if I get this working I'm going to pick up wireless card for 4 of the pcs.)
What I'm trying to do is create a private network for local file sharing but also have internet access. There is a WRT54G router connected to a satellite modem in a separate building, just barely close enough to connect from my laptop, which is what sparked my original idea to use my WRT54GL as an access point.
Due to the way I have my DSL and VOIP TA configured I need to be able to set the subnet mask in the Internet connection. I am currently using the Static IP, putting in an IP of 192.168.1.x with the subnet of 255.255.0.0 when I try to do this it gives me an error saying that 192.168.33.1/255 is reserved for the guest network. I am not using the 33 at all ANYWHERE. If I change the subnet to 255.255.255.0 it will save but I can't connect to the internet with it. My router I just bought today is the E2500 I have an old Linksys WRT model that worked fine with this exact setup for several years before it crashed on me.
set up my router. Trying to set up my 3G modem with TP-Link MR3020.
Tried troubleshooting to find out where it went wrong and just couldn't figure out. Just tried disabling the wireless security and *poof* I'm able to connect to the Internet. Right after setting up the Network Key, I can't connect to the Intertnet via my router.
Here are the datas.
Windows IP Configuration Host Name . . . . . . . . . . . . : TOSHIBAM840 Primary Dns Suffix . . . . . . . :
Earlier today I attempted to change the setting on my Westell 6100 modem such that it would simply bridge the connection to my Linksys WRT54GS router, basically involving setting the router to bridge only and turning DHCP off. Now I no longer get an internet connection through my router when previously the connection had worked perfectly fine before. I following the steps of cloning the MAC address to the router and have done the proper resetting steps (computer, them router, then modem) but I simply can't get an internet connection through my router. The process to set up simple bridging from the modem what supposed to end up with the internet light no longer turning on but the light turned back on following one of the resets.
Currently, I can connect to the internet through the modem just fine but I get nothing when I include the router. I'm not sure if there are some other settings I'm supposed to be changing as I can't seem to find anything past what I've already done when researching online. At this point I would just be happy reverting the settings I've changed but I don't know how to access the modem now that DHCP is off.Basically, I'd prefer to be able to get the router working with these new settings but if that proves too difficult (as I've heard it can be when trying to get Westell modems to work with Linksys routers) I'd like to learn how to access the modem and change the settings back to what they were (preferably in as simple terms as possible as I don't particularly understand what a lot of these settings/configurations do).(And a bit of an aside, but I had attempted to do this modem bridging to "fix" perceived internet speed problems. I've been averaging around 300Kbps download rates ever since I've had this internet connection from Verizon when the supposed download rates should be between 1MB and 1.3MB. Doing this modem bridging had been reported to fix some modem/router conflicts and improved connection speeds for some.)
setting up an ASA 5505 to be used as a firewall between a BT internet router(BTNet service) and a Cisco 3560 Lan switch. BT have presented me with a cisco 3800 series router with the following details:
Network Address Network Mask BTnet NTE Router LAN Address
There are 2 Gigethernet ports on the back of the router port Ge0/0 is connected to the BT NTE and the status light is flashing green. Int ge0/1 is connected into port int e0/1 of the ASA but i am unable to get any connection.
I am currently setting up a new VRF on a Cisco 7609 which is advertising (as a RR-Client) an iBGP route to a Juniper MX960. This route is then getting sent back to the default route table on the 7609 but rejected due to the cluster-id loop prevention. Although not ideal I need this route to be visible in both tables.Is there a way of changing the bgp cluster-id per VRF rather than just globally?
setting up VPN on my CISCO 851 W-G-A-K9 version 12.3 ?I read on the cisco site that it supports VPN and L2TP and PPTP Tunnels?I did a show VPDN and itt shows no tunnels setup?I use a hyper terminal connection and make all my changes via command line?
I run a windows 2003 server environment with active directory that I have some remote users that I would like to logon to the network?I also have a laptop that I would like to take on the road and be able to logon via vpn?what commands would I need to set this up
I can do simple command like
enable conf t ip nat inside source static tcp xxx.xxx.xxx.xxx 25 interface FastEthernet4 25 exit wr mem enable
Currently we are using a Windows 2003 Server with VPN Sever Role for VPN Access and my users use the built in VPN connection with Windows client. In the past few weeks we upgraded our router/firewall to CISCO ASA5510.
My understanding is that I get 1 or 2 VPN licenses with the Cisco ASA5510 and I would like to configure to test Cisco VPN access. My first question…when I configure the Cisco ASA5510 for VPN (Clientless or via Client), do I need to point the Cisco to my Windows 2003 Server with VPN role on it or the Cisco ASA5510 handles the VPN connection and access?
