I'm looking for a wireless handset that is compatible with a Cisco IP Phone 7940 Series. All I can seem to find are wireless headsets. Basically, I just need a cordless phone I can plug into the phones we already have in case we have to step away from the desk or office. We don't want to use headsets. Where I can find something like that?
View 1 RepliesI am facing a constant problem with cisco 7940 Ip Phones.
- I am able to configure it from Call Manager.
-But after that the phones starts restarting.
- I heard there is some issue with CISCO 7940 Farmware in recent times.
How to upgrade Firmware and where to get one.
What's the best router / handset to get to practice for CCNA Voice?
View 2 Replies View RelatedI have two phones Cisco 7940 with firmware 8.12. Configuration:
line1_shortname "George Steel"
line1_displayname "George Steel"
line1_name: 1
line1_authname: 1
line1_password: 123
When I call to another phone as the caller's name appears GeorgeSteel (no space). With firmware 8.8 it does not do ..
How to connect N76 bluetooth headset to a laptop, works with handset (cell phone)?the laptop is not seeing the headset when searched
View 1 Replies View RelatedI have a Cisco 6500 which has two VLANs defined
VLAN 30 for Data VLAN
VLAN 31 for Voice VLAN
I have two Cisco 3750 switches.both switches are connected to IP Phones.the configuration of Cisco 6500 Trunk Port to Cisco 3750 is [code] On Cisco 3750, the trunk port to 6500 has the configuration [code].The IP Phones connected to the Cisco 3750 are 7911,7979, 7940, 7961.
All phone are working fine, the phones get their ip address from voice vlan, and systems connected to phones get from data vlan, except 7940/7960.
These two models of IP Phones remain on Configuring IP, and when you check the IP Settings, it gives Data VLAN IP, which does not have a TFTP.once you manually enter TFTP address in the field, it registers instantly, due to ip routing in the network.
these phones were working fine before, but suddenly few days back they went out of the network, and still are in Configuring IP state.I also tried to convert these ports connected to 7940/7960 to access ports [code] but still the IP is taken from the Access Vlan (30). Even If you configure a single VLAN on these ports, the IP phones then never get the IP.
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedWhat's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View Relatedwhy I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedI have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies View RelatedCurrently using PC fax/modem card with landline phone cord to send/receive faxes. I live in a very rural area that has really crappy landlines for my phones. Will be getting a Verizon wireless phone system that has 2 RJ-11 interface jacks so I can connect my current landline phones to the wireless system. Is there some way that I will be able to use my PC fax with this Verizon system? The Verizon salesman wasn't sure but didn't think so.
View 2 Replies View RelatedI have a DSL wireless router in my house, I would also like to have wireless in my workshop. It's over 130 feet to the shop so my house router won't reach. when I built my shop I put an extra pipe in to pull phone line in but now I'm wondering if i can just pull in a cat 5 and get both data & phone.
View 2 Replies View RelatedI have a simple question and i am new to wireless networking.. I recently bought a wireless router to share my internet connection with my mobile phone ( Sony Ericsson Neo V).. My PC doesn't has a Wifi adapter so I have connected router to pc via a network cable.. Now I want to send my files to mobile phone and can i do that through my router? or should i buy a wifi adapter to pc and directly connect to phone?
View 3 Replies View Relatedi have a wlse setup in a small orgnization and have c1130 aps connected to lan netwrok and with two broadcast ssids,and i have cisco ip telephoy setup too, now i want to connect some of cisco wireless phone to connect through the wireless,as i said that i have two ssids and both are working very fine,so my question is that on lan switch side i have configuration:interface GigabitEthernet1/0/9 switchport trunk native vlan 54 switchport trunk allowed vlan 51,54,58,59 switchport mode trunk spanning-tree portfast.
View 2 Replies View RelatedWe just installed MSE with CAS (7.0.201.204 software) and everything works fine and clients are shown on WCS floor maps except for Cisco 7921 wireless phones which dont appear in the WCS map.
View 3 Replies View Relatedhave configured Cisco IPPhone 7925G with EAP-TLS setting. (With manufacture installed and Userinstalled certificate). My issue is while roaming from 1 AccessPoint to another AccessPoint the call getting droped. I need to restart the IPPhone to reauthentiate again. In ACS am agging the authentication time-out error. (I had changed the time out value for EAP-TLS to 20 in WLC as per recommendation.)
If am using static web key there is no issue in roaming.
What is the reommended setting inorder for the EAP-TLS to work properly.
I have a wired IP phone connected to my company network, in my home office. How can I convert this to wireless so I may use other rooms in the house to work in?
View 1 Replies View Relatedcan't connect to wireless internet on phone
View 1 Replies View RelatedHanging up our cordless phones briefly interrupts our wireless connection. Just long enough to be disconnected from online games.We are using DECT 6.0 Vtech phones (definitely not 2.4 ghz phones)We have verizon FIOS internet (not DSL)I've tried changing channels in the modem with no success.
View 5 Replies View RelatedI'm getting high utilizatiom from a 7921 ip phone and call quality is getting very low sometimes. What can cause this high utilization?802.11 Mode 802.11a Scan Mode Auto Restricted Data Rates False Call Power Save Mode U-APSD/PS-POLL BSSID xxxAccess Point xxxTx Power 15 dBm Channel 44 RSSI -57 Channel Utilization 153 DTIM period (ms) 2 Security Mode Shared+WEP Encryption WEP Key Management Shared
Load Information
Load Profile................................. PASSED
Receive Utilization.......................... 0 %
Transmit Utilization......................... 0 %
Channel Utilization.......................... 69 %
Attached Clients............................. 4 clients
I am trying to follow the steps to type in the 192.168.1.1 but all the username and passwords arent working for me.. How can I get my wireless to connect to my smart phone.
View 1 Replies View Relatedwhat is a wps button? I can't load my pictures from my phone to the internet so I can print them?
View 1 Replies View RelatedI have a VOIP WiFi phone (MIC505W) I have configure it according to the user manual.I get access to WiFi, but when I dial a number I get busy signal with the message "disconnet".
View 3 Replies View Relatedmy wireless connection always drops when my phone rings. i have a hp compaq presario cq56-115dx notebook pc and a 2wire 496 wireless rounter and i loose connection during internet exploring. WHY?
View 5 Replies View RelatedI know the AP541N can support the 7921 phone but all the documentation I've read assumes the AP541N is registering the phone with a UC500 system. I was curious if there would be any problems using this AP with a 7921 at a remote site (881SRST gateway used). It would be tieing into a CUCM BE system at the central office.
View 0 Replies View RelatedWe have a UC500 with 3 access points AP541N. We need to move around the building so we use wireless voice with 7925G phones. All works fine except when the phone needs to change from one AP to another. We lost connection for a small interval of time and then resume normal operation.
View 1 Replies View RelatedI have configured a cisco UC520 with inbound called coming in on FXO port 0 and have configured it as a co-line. I have 4 phones set up on the system including the wireless 7921 phone, the problem is that if i answer the call on the 7921 it does not give me the option to hold or transfer the call however the other phones do (7931).
View 1 Replies View RelatedI have CUWN, WLC 5508 is installed and APs are 1142. Network is working fine but I am facing the problem with Android phone which are not browsing for internet.
Android phones connectes with wi-fi, it takes IP from DHCP well, which is pingable from any node of network. even I got be GUI of WLC on Android, but when it goes to browes for internet the message displayed " Page cannot be disply".
In same scenario if configure the Public IP on Android Phone (Via DHCP or Static) then it runs the internet smoothly.
Is it possible to integrate a wireless voip cisco 7921g (sccp protocol) with an small business modem router Srp527w (sip protocol), even if if is by connecting another device (like an access point) between both? I know skiny is cisco property and sip is an open source protocol, so I do not understand why cisco does not implement the skinny protocol in his Srp527w.
View 5 Replies View RelatedRecently got satellite high speed. Am trying to hook up the wireless router my son gave me. Installed and set up but my PC doesn't recognize it and my phone won't pick it up.
View 2 Replies View Relatedrecently we have deployed a Two APs in branch office warehouse and I have one wifi phone 7925 used over there. the problem is every time when phone roaming from one AP to another, 2 or 3 packets dropped, following is result of the 'debug client ':
--More or (q)uit current module or <ctrl-z> to abort*apfMsConnTask_7: Jun 27 09:52:25.496: 88:43:e1:4f:ab:39 Association received from mobile on AP a0:cf:5b:c3:a8:90*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 10.107.38.121 RUN (20) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 Applying site-specific IPv6 override for station 88:43:e1:4f:ab:39 - vapId 14, site 'AKL-AP-GP', interface 'management'*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 Applying IPv6 Interface Policy for station 88:43:e1:4f:ab:39 - vlan 38, interface id 0, interface 'management'*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39
[code]....