Cisco Wireless :: WLC 2504 No Console Connection
Jan 29, 2013
We have a WLC 2504 which has been configured, however our old admin left and we can not access this device. We verified our serial connection works - 9600; 8bits; 0 and none works on other devices. When we connect (via Console) we get a blank screen with a blinking cursor. We can't get to it from GUI/Web as well. Tried depressing the reset button and we see the LED's flash from yellow to green, but still no access. Our web search has not produced any useful ideas.
View 2 Replies
ADVERTISEMENT
Nov 28, 2012
Can I set up a guest wifi connection on my Cisco WLC 2504 if I already have WLANs set up inside my corporate network? I want to use port 4 and connect it directly to my ISP so that it is outside of the corporate network. I set up an interface with a valid IP from the ISP and created a "Contractor" WLAN to use that interface.
View 6 Replies
View Related
Dec 4, 2012
We have a 2504 WLC and 8 352l AP. All AP are working and can be seen in the WLC except 1. It can grab an ip address but cannot see on the WLC. the show AP join...only shows that it is trying to join but no error indicated. A debug cap swap events didn't show the ip add.
View 7 Replies
View Related
Dec 6, 2012
I am currently experiencing an issue with a WLC that I am trying to connect 3 new Access Points to of the type AIR-LAP1142N-E-K9 running Cisco IOS Software, C1140 Software (C1140-RCVK9W8-M), Version 15.2(2)JA
I had the controller on firmware 7.0.220.0 and just upgraded to 7.3.101.0 in the hopes to solve my issue. The already connect APs running 12.4 was upgraded without any issues (apart from one - I'll get to that one) and it is now running as before. But the issue with the 3 new APs still persists. I have supplied a screenshot of the AP Join page.
Another issue that arose from the said upgrade was that a previously shutdown AP (of the same type and software version as the ones that upgraded perfectly) got turned on after the WLC firmware upgrade and is now not able to join the controller.
View 20 Replies
View Related
Aug 8, 2012
I need to use very long console connection it over 56 feet (17m) (I used Cat6 wire with connection on oth ends as console wire 12345678-87654321) According to the below table
Data rate (bps)Distance (m) 2400
60
4800
30
[Code]....
View 1 Replies
View Related
Jun 11, 2013
I have two 3560s that i would like to upgrade. But first i would like to make -absolutely- sure i dont wind up in a situation where i have to roll back over a console connection.to the day i still cant understand why oh why someone removed (or chose not to implement it everywhere) tftpdnld from rommon ;)
View 8 Replies
View Related
Aug 13, 2012
Everytime the console port is plugged in, the alarm contacts (1-4) randomly assert (trigger) and then clear themselves in random orders. Nothing is plugged into the ALARM port and all Alarm setting are default. Below is the syslog message and Alarm Settings:
CGS2520-C#show env allSYSTEM TEMPERATURE is OKSystem Temperature Value: 45 Degree CelsiusPOWER SUPPLY 1A TEMPERATURE is OKPOWER SUPPLY 1B TEMPERATURE is DisabledPOWER SUPPLY 1A Temperature Value: 49 Degree
[Code]......
View 3 Replies
View Related
May 10, 2012
I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
View 3 Replies
View Related
Feb 16, 2012
So I have read about proper procedure involving the connection between a console cable and Hyper-terminal. I have also tried plugging into a network port to obtain an IP Address but nothing seems to work. When powering on the switch I see that it lights up, hear fans spin and assume it has booted properly. I'm using Hyperterminal on Windows Xp Pro SP3 and I've also tried minicom in Fedora.
And just FYI Hyperterminal was set to the proper:
Bits per second: 38400
Data bits: 8
Parity: None
Stop Bits: 1
Flow Control: None
View 1 Replies
View Related
Apr 3, 2011
My Wifi internet was working fine 12 hrs ago; now I can only use it with wire.I uninstall 2.0 and install Asus wireless console 3.0 but still not working, Fn+F2 not working either.
[code]...
View 2 Replies
View Related
Dec 19, 2011
I dont think my cards are faulty (4 cards in 2 6500 switches),I connect directly to my WISM cards, boot them (insert them), I see it turning on, enabling services, and as soon as the "username:" prompt apears, the Status led turns off and I lose console. [code]
View 21 Replies
View Related
Apr 23, 2013
my client claimed that right after thry upgraded their WLC 4402 to version 7.0.220.0 from the version that came preinstalled (factory) the can no longer console into the device. They were able to console into the 4402 before the upgrade but now they can't. I'm thinking that maybe they upgraded straight to the new version and didn't verify to see whether they were allowed to upgrade directly to that version 7.0.220.0 or if they needed to upgrade to a intermediate version , the proceed to upgrade to the 7.0.220.0.
View 3 Replies
View Related
Jan 3, 2011
We forgot the IP address of this WAP, and resetting the router doesn't take it to the default IP, no matter how I try to reset it. The SSID (and WEP key) stays the same too, which makes me wonder if the reset button is even working. We can still connect computers wirelessly through it and have them access the internet. Our issue is we need to change the SSID. Right now it just connects people invisibly - it gives them IPs from the subnet it's attached to, and yet the various DHCP servers I've connected to never show it as having its own DHCP address.
View 1 Replies
View Related
Jun 6, 2013
I have been having problems with a 2106 WLC which seems to have developed a fault. I cannot console into the device (although I can console into the ap1131ag showing no fault with the RJ45 - 9 Pin) and the device is no longer showing up in any of the possible I.P ranges.
Its showing a power light and a status light on the front panel, the Ethernet ports light up like a Christmas tree when a device is connected and the power supply is putting out a solid 47.7v.
Has anyone experienced anything like this before and can anyone suggest anyway of breathing life back into it?
View 5 Replies
View Related
Sep 5, 2012
They brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
View 14 Replies
View Related
Feb 13, 2011
I'm having an issue with our WAP2000 access point. I had to reset the access point and now I can't access the admin console. I've set a static IP address just as I did when I first set it up. Now when I browse to the 192.168.1.245 in my browser it just displays an Authentication error.
View 1 Replies
View Related
Jun 21, 2007
I made a lot of tests during some days with a wlc4402 and everything was ok.
One day when I tried to reset the system I had a lot of errors (see attach) and could not go on. After changing the image the following output appeared: "RAM Disk Image Integrity Check Failed (Bad Magic Number) Hanging". Now I have no response from the controller.
View 4 Replies
View Related
Jan 18, 2011
Recently we had a situation where our users were unplugging one of our un-mounted 1252 LAPs. They would do this so they could borrow the wire to direct connect any one of their devices not realizing they were disconnecting a wireless access point. After discovering that the AP was unplugged once again, our admin plugged the AP back to the network but noticed that it no longer would connect to the controller. We can no longer console into the AP but can console into all other APs we have. All 3 lights are now green. Radio and Ethernet are solid and Status is blinking. I found the Cisco doc explaining the meaning of the front panel lights but have not found this particular configuration. What these lights mean and why not being able to use the console port?
View 11 Replies
View Related
May 2, 2012
My Linksys Routers IP is 192.168.1.1 am unable to access the console, although i changed the computers IP 192.168.x.y. i have tried by Hard Resetting the Router but still the same?
View 1 Replies
View Related
Nov 27, 2012
Region : Poland
Model : TL-WR842ND
Hardware Version : V1
Firmware Version : 3.12.22 Build 120424 Rel.39632n
I recently bought an new router TP-LINK TL-WR842ND. After configuring it I connected it via an cable connection to my PS3. The Internet connection works correct and I'm able to use all network feature on my console.
Then I connected a USB Hard Drive to it USB port and I enabled Media Server feature on the router. I have done steps described here url... but with no results. My PS3 sees the Media Server, but when I open it it shows no files.
View 7 Replies
View Related
Jan 31, 2013
Region : UnitedStates
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : TL-WR941ND_V2_V3_120201
ISP : Cox
I updated my firmware due to connection issues, now it gets stuck when trying to load the console. I can see the grey pipe separators on the screen, but nothing else. I've tried chrome, firefox, and IE, but still nothing. The wireless AP is active, and i can connect wirelessly, and i can ping it. just cant get the console to show.
View 9 Replies
View Related
May 7, 2013
We are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).
View 4 Replies
View Related
Mar 2, 2013
Why a 2504 Poe? If it can not be used for AP.
View 10 Replies
View Related
Jan 22, 2013
I'm planning to upgrade our WLC 2504 from 7.2.111.3 to 7.4.100.0 but the cisco site says "WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time" Is it something about NCS? we have only 1 cisco WLC 2504 and 6 1142APs.. Also let me know is it possible to go directly from 7.2 to 7.4 ?
View 8 Replies
View Related
Nov 28, 2012
what is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
View 8 Replies
View Related
Aug 29, 2012
I've problem with a WLC 2504. Some Clients like phones and Thin Clients get an IP 0.0.0.0.Software Version is 7.0.235.0. Test with a Laptop seams to be OK. Some printers also got an 0.0.0.0.Around 30% are not OK. also had the log: Impersonation of AP with Base Radio MAC 00:yy:yy:yy:yy:yyusing source address of 00:xx:xx:xx:xx:xx has been detected by the AP with MAC Address: 00:yy:yy:yy:yy:yy on its 802.11b/g radio whose slot ID is 0 The problem is, I cannot go to 7.2 version because I have 2 x AP 1231 and 2 x 1242 AP's.1231 AP's are not anymore supported in 7.2 Version.
View 14 Replies
View Related
Aug 15, 2012
I have two WLC 2504 controllers. These controllers are for two different buildings. But they share a VLAN, and network address range. How can I control the access points to the register selected only at a specific controller.
Example:
AP 1 -> WLC 1
AP 2 -> WLC 2
AP 3 -> WLC 1
Since the buildings also broadcast in different SSID. The two controllers are in a mobility group.
View 4 Replies
View Related
Jul 12, 2012
If we update our ios on WLC do we have to add the certificate for AP's again or we don't need to do that.
View 4 Replies
View Related
Mar 13, 2013
Some time ago I updated a WLC, model 2504, from version 7.3 to 7.4.100.0. I also update the FUS (Field Upgrade Software) to the latest release, 1.8.0.0. Now I need to downgrade the WLC back to 7.3 version.
My doubt is: Can I just take the normal processes and downgrade the WLC back to 7.3, even with the FUS in version 1.8.0.0?
View 5 Replies
View Related
Jun 10, 2013
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
View 15 Replies
View Related
Jun 13, 2012
I'm using Linksys WAG200G Wireless modem and connection mode is "Bridge Mode Only", in this mode I'm not getting the 192.168.1.1 setup console and Wifi facility.
View 3 Replies
View Related
Aug 2, 2012
I currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies
View Related
Mar 12, 2013
I have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch 2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?
View 4 Replies
View Related
