when you have a device that you don't know it's IP what do you do to find it out, I normally just plug directly into the device and use nmap to scan the ranges I think it might be, but that takes quite some time?
View 17 RepliesI have various unknown Mac addresses on my network,detecting if they are normal/non harmful OR if I've been hacked! I've uploaded a picture of the addresses, the second to the last address is my router's.
View 1 Replies View RelatedI noticed two ip addresses reserved with DCHP on my home wireless. From IP addresses I can't seem to figure out who these belong to at home. All connected computers and devices are accounted for. Could these possibly be someone(s) hacking to my wireless to connect to internet? Or are these for modem setup, etc.?
View 2 Replies View RelatedI have various unknown Mac addresses on my network, I need to detect if they are normal/non harmful OR if I've been hacked! I've uploaded a picture of the addresses, the second to the last address is my router's.
View 14 Replies View RelatedWe have reserved ip addresses for all computers in our DHCP server. But sometimes we notice that some of our staffs put manual ip in their computer and so far I have no idea how to trace it from server itself without visiting each computer to check it out.
View 3 Replies View RelatedI have recently purchased an SG-300-52 Managed Switch. (This is the first managed switch I have used, so I am trying to figure out what I can do with it and how it works.)
I would like to know how to find out the IP address of each computer connected to each port of the switch. Is this possible and if so how can I do this from the browser interface?
How can I find out the ip addresses of contacts in social networks
View 2 Replies View RelatedFind list of all the MAC address of the devices connected to the router?
View 2 Replies View RelatedIn setup for old RV042 (V1), when updating / adding Mac addresses, the table is always sorted by IP addresses. But in the new oneRV042 (V3) I have, even with latest firmware 4.2.1.02 the list is random, thereby increasing the chance of user entering DUPLICATE IP addr with diff Mac addr. That will result in conflict.If the firmware sorts the DHCP entries by ip addresses, user would be able to catch duplicate ip errors even if the system does not flag the errors. All Cisco smart engineers can you all get the dhcp entries SORT by ip addresses.
View 2 Replies View RelatedWe have a daisy-chain like network at my work involving various cobbled together parts such as Print Servers and switches. Today a random computer has appeared on our network with the name USER-U40PVRNHWL. We do broadcast a wireless signal, but it is password protected. I have done a complete sweep of the building and there are no extra pieces of hardware physically connected into our network.
View 1 Replies View RelatedAfter successfully install a device update for Common Services, all devices are reported as unknown.Number of Packages Selected for Install : 2
-For Product(s) : Common Services
-Install Invoked by user : ameconi
-The Package(s) Selected for Install :
When I try to install other updates these fail because MDF is version 1.59.
We are running Cisco Wireless Control Sytem (v7.0.164.0) with 4 - WLCs (v5.2.193.0) and about a 100 Aironets and I was wondering how to get WCS to identify the Client usernames? When trying to view monitored clients usernames, all it shows is Client Username <unknown>, though their MAC and IPs are correct. I'm not sure if this has to do with mobility anchors or not, but currently we have none setup in case. How to resolve the machine name or actual username that is logged in... either one.
View 2 Replies View RelatedI set the asa Vpn to connect to the other firewall, the VPN is ok but when i see the logs of bytesTX and BytesRX the asa receive a lot of packages in BytesRX but dont send anything in BytesTX.
View 1 Replies View RelatedMy customer had 2 asa5520 version:8.0(5)20 and LMS 4.0.1.Two Firewall are "unknow" on LMS, why ?Normally, LMS manages ASA with version 7 min.
View 1 Replies View RelatedSince i got sky broadband it's always been running super slow, the amount of times i have called them is ridiculous. So i have just been looking around on the sky address to see if i can fix it and in my Attached devices i have, the pc, an ipod touch and an unknown device. I'm wondering if this has anything to do with the slow speeds and maybe it's somehow 'stealing' my broadband. I've read a previous post of the same type but that wasnt for sky. i ran the ipconfig/all into CMD
View 1 Replies View RelatedIs there any solution for the usb wireless which its chipset is unknown when u do the airmon-ng
View 1 Replies View Relatedmy wifes computer had to have a new hard drive installed an since it was fixed it will not network with my laptop in a private mode only public and my laptop now has a question mark then step down her old computer as the network path we are both windows 7 hers is hp and my laptop is toshiba satellite I can not get rid of the 2 networks from her computer or the question mark on mine
View 2 Replies View RelatedWe had a new linux server installed at a remote office yesterday, unfortunately the guy installing the server forgot to change the IP addresses, doh. It's plugged into a C877 and I can see the port is up/up and I see the mac address using 'sh mac-address-table'. The ip address on the server is unknown but it's unlikely to be in the correct subnet for the vlan it's attached to.
Is there a way I can add an arp entry manually to the router, then ssh to the server and correct the ip address? Or is there some other way to establish the IP address of the server? It's gonna be a pain to revisit the office and there's no one there that can get into the server room to do anything from the console.
This might actually go into Networking Basics because of the nature of the problem, but I tossed it in here because of the Cisco product involved. Long story short, I need to do some detective work to figure an apporpriate IP address for a NIC.I recently started working at a company with the ASA 5505 and I need to upgrade the software image on a bunch of them. There's already a computer set up with a TFTP server and Hyper-Terminal to do it. I'm trying to use the CLI update procedur[URL] but when I get to the beginning of the actual transfer from the TFTP, I get stuck at "Accessing" and then the connection times out with the message "Unknown Error".The only thing I can think of is that somehow the ASA is not making it all the way to the TFTP server, probably because the IP address settings on the NIC for the computer is set wrong. I say this because in the config file provided me, the ASA is given an address X.Y.Z.1, subnet mask /24 (where all the letters are constants) and the TFTP server has an addess in its software config of X.Y.Z.10 mask /24, but the NIC on the computer is set to A.B.C.105, which is an entirely different network.I need to figure out what I can make the NIC IP address so I stop getting the error. I tried a couple of different X.Y.Z.x addresses, but haven't gotten anything yet.
View 1 Replies View RelatedI have got a problematic 1841 router. I connected it with console cable and use HyperTerminal application with
BPS: 9600
Data Bits: 8
Parity None
Stop Bits: 1
Flow Control: None
but the displays shows as follows. What may be the problem ? I can't see the English language, what to do now ?
ËŠª¨GÌÍ(W•³•BÜΣ¥õ«©¡«©¡GfGMèF£eˆ)¯+%©§§Mr§j‹ ï(MŽV»øìõ3B…«»v£FÝ=;VOèF£eˆ
)¯+%©)§N N'vnjj»³6r³h-Bãeˆ)¯+%©)'f¾.zN' ~R5ˆîïÝèv®V££õ£ë£'%3Þ££õF£ÈMèF£eˆ)¿+
%/]'fnno/?míHv£îïÝèv®V££õ£Œî£'%3v££õþ
I have issues to connect Cisco 2911 to HP switch. I disable CDP on the LAN port, router at A end is ok, but the unknow protocal drops as same as before at B site. It happend around every 30sec. When I transfer a file from one end to the other end. It always disconnect every 25 second. HP Switch is not configure trunk as it work as a plain network
View 3 Replies View Relatedi have a desktop and a laptop(dell xps 14).and am using a modem to connect both using ethernet cable.my modem is showing lan connection of both computers.but there are problems which are- i cant connect to my homegroup i cant find any server on lan while playing games i cant share files
a network driver is missing.details are- property-hardware id values-ACPI/SMO8800 *SMO8800 also specified that first value is highlighted and error code is 28
After getting unusual IP conflicts on my laptop, I did a scan of my home network with a program called Zamzom and got the following results:On my Macbook I used a similar program and got more than 40 devices showing up: Neither program says which devices are active. The Mac results bring up BlackBerrys among other things. I upgraded my security from WEP to WPA2, but nothing changed. I use NOD32 and recently installed AdAware, which picked up a few things, but again, results are the same.
View 7 Replies View RelatedWhen I go into the Network Settings, and the end of the page I find a list named "Number of Dynamic DHCP clients: 7". As far as I know, I should only see 4, all 4 laptops; however, I see 2 UNKNOWN entries in this list, and one name "Macondo". Each of these entries have an option (a link) saying "Revoke" and other "Reserve". I am just wonder if these entries are intruders in my home network. What should I do? I am afraid to break my internet connection. By the way, I set up every single one of my family 4 laptops at home with a WPA-PSK using a very long key.
View 9 Replies View RelatedI use a Ethernet Powerline adapter.Right now, there are 5 other computers on my wired network, and i don't know what they are. What are they doing there, and how do i get them out?
View 6 Replies View RelatedThough ASA5585-X S-20 and UCS C200 are not in LMS 4.0 supported device table, I'm wondering if there is any way to monitor these devices using LMS? Our data centre has a quite number of UCS C200 servers and two ASA5585-X S-20.
View 7 Replies View RelatedI know the way to configure the ASA to fallback to LOCAL authentication, if the Radius server is not available.
Now we would like to authenticate the local users, if the user is not found in the AD. Is this possible and how can I configure this with the new policies? I tested it with "dropping" when the user is not found in the AD, but then the Radius server will be marked as "dead" and the other AD users can't login for a given period. Maybe we can configure the dead time to 0, but this is not as nice it could be.
There is a Linksys RV016 router setup at my workplace. I need access to the webmanagement interface however the default password is not working. (Username/Password: admin/admin) Is there any way to obtain the login information without performing a reset of the router so I do not lose its current configurations?
View 3 Replies View RelatedOne of our ACE-20's crash recently with little info as to why - fortunately it was the FT standby module so service wasn't impacted but obviously keen to determine the cause of the crash, and potential resolution.
Running A2 (3.5).
last boot reason: NP 1 Failed : NP Core Reset - Cause Unknown,There is nothing obvious from the switch perspective:
Apr 17 14:52:35.775 bst: SP: The PC in slot 9 is shutting down. Please wait ...
Apr 17 14:52:45.780 bst: SP: PC shutdown completed for module 9
510497: Apr 17 14:52:55.781 bst: %C6KPWR-SP-4-DISABLED: power to module in slot 9 set off (Reset)
510498: Apr 17 14:57:58.277 bst: %DIAG-SP-6-RUN_MINIMUM: Module 9: Running Minimal Diagnostics...
[Code]...
I have to access Remote Desktop Connection for a new job that I was supposed to start today (work from home).When I go to log in it brings up the computer's old name and won't let me access without a password.I'm working off my husband's pc & he can't remember ever using a password on it.About a year ago I reconfigured the pc and reset it's name and administrator but there were never any passwords involved.
View 2 Replies View RelatedI found two unknown computers on my network (using Explorer). I have a wireless setup at home (private) with a desktop (wired), two laptops and a phone (wireless).The encryption is WPA2/TKP with a hard to guess password. The two unknown computers were connected this morning and a few minutes after I tried to access them and do some checks,they disappeared could they have been watching me? I didn't check the router page until then and of course, they weren't there.Also, yesterday I was at a coffee place, so could it be that this is nothing and those two computers are from people at the cafe? Is there anything I can do to make sure nobody can access my network, unless it's the computers I want. I haven't manually set up a home network yet. [code]
View 4 Replies View RelatedIs there any software,proxy are possible by which we can connect our laptop to wifi without security key.
View 3 Replies View RelatedMy desktop's internet connection is acting up. It's always worked fine, then all of a sudden it has stopped. I can still access MSN messenger and Paltalk, perfectly fine, and it is showing that I have an internet connection. However, when I open any of my browser windows, it cannot access the internet. My laptop and ipod are connecting fine on the wireless. I have my ethernet cable from the desktop plugged into the router, which is plugged into the modem. I CAN force the connection to work by 'talking' to the modem (using the IP address) and doing a disconnect and reconnect. This lasts for a little while, then it stops again. When I do my network map, it shows an 'unknown device' where the modem is supposed to be. When I disconnect and reconnect the modem, it changes from 'unknown device' to 'switch'.
View 19 Replies View Related