We have reserved ip addresses for all computers in our DHCP server. But sometimes we notice that some of our staffs put manual ip in their computer and so far I have no idea how to trace it from server itself without visiting each computer to check it out.
View 3 RepliesI have my other XBOXs connected to a 24 port switch but the one connected to the ea6500 directly gives me this moderate NAT issue. I thought this new router would be an upgrade to my old dlink but so far I get a new problem every day.I have reserved dhcp addresses for all the boxes and set up port triggering for the ports listed in several guides. But what else do I need to do? Is it likely I got a bad router?
View 2 Replies View RelatedWhere do I find a manual for the LinksysE1000?
View 1 Replies View RelatedManual and firmware not available for my f7d2401nt. The US support page do not find the model, the italian support page find the model but link to the US page ! Someone has at least the manual (englis, french or italian language) ?
View 2 Replies View RelatedN600 DB on OSX. I keep on reading the material that there is a link on the dashboard that I click on to set up the router manually. Nowhere on the dash board is that link. Where is that link?
View 1 Replies View Relatedwhen you have a device that you don't know it's IP what do you do to find it out, I normally just plug directly into the device and use nmap to scan the ranges I think it might be, but that takes quite some time?
View 17 Replies View RelatedHow can I find out the ip addresses of contacts in social networks
View 2 Replies View RelatedFind list of all the MAC address of the devices connected to the router?
View 2 Replies View RelatedI have recently purchased an SG-300-52 Managed Switch. (This is the first managed switch I have used, so I am trying to figure out what I can do with it and how it works.)
I would like to know how to find out the IP address of each computer connected to each port of the switch. Is this possible and if so how can I do this from the browser interface?
My galaxy tab has a difficult time connecting to my wifi. it seems that the only time my galaxy will connect is when i change the DHCP reserved IP address i setup for it. it wouldn't connect before i setup a reserved IP address. now my galaxy tries to connect over and over and won't until i change the reserved IP address by a few digits.the router is an older d-link wbr-2310. i know routers occasionally die, but this is the only problem i have with it.
View 10 Replies View RelatedI'm configuring ASA 8.4 for SSLVPN allowing Web Portal access with group-url. I've noticed that if I put certain keywords after slash mark on group-url, client access would be denied by http 404 error.
Here's my configuration:
tunnel-group test type remote-access
tunnel-group test general-attributes
default-group-policy test
[Code].....
each time i type my email and password a red message appears telling me that the account domain is reserved
View 1 Replies View RelatedI wanted to know if you can setup reserved wireless IP address on the WRT54G router. With all the kids devices, when I reset the router, getting all the devices online is a challage. Some end up with duplicate IP address causing conflicts. If I could reserve an IP address for a specific device. Let me know what option the router has?
View 3 Replies View RelatedI have a Cisco 2911 router and a Cisco 2960 switch at a remote location.I have a user who will work out of this office a few days out of the week and will need to obtain the same IP address everytime the user visits this office. This office has no file server, no dhcp server. I have the user's MAC address and for now, the user is getting an IP address that is leased for 30 days. I'm trying to find the best way to configure either the router or switch or both so that each time this user connects to this office, that user device will always pull the same IP address and of course no other device will use that IP.
I've did some research in creating a small vlan possibly, and assigning it specifically to the port# that the user's desk is at, but not sure if that's the best way or exactly sure how it'll work. I'm currently studying for my CCNA so this is all new to me and I'm trying to do research and test without obviously causing production issues especially given this is a remote site and I access these devices via putty. I can however drive to the site if needed for testing, but I'd like to have a good grasp on what method I'll be using that will work before I actually make the trip.
In setup for old RV042 (V1), when updating / adding Mac addresses, the table is always sorted by IP addresses. But in the new oneRV042 (V3) I have, even with latest firmware 4.2.1.02 the list is random, thereby increasing the chance of user entering DUPLICATE IP addr with diff Mac addr. That will result in conflict.If the firmware sorts the DHCP entries by ip addresses, user would be able to catch duplicate ip errors even if the system does not flag the errors. All Cisco smart engineers can you all get the dhcp entries SORT by ip addresses.
View 2 Replies View RelatedWe have modem router 4-port with IP range 10.0.0.1 - 30 setting.one port goes to a library where we have a 8-port switch STLAB SWHUB-8p serving 2 pc with auto IP setting (internet works fine)and one port goes to another corner of the library to a switch TP-LINK TL-SF1008D V4.1 .4 pc are connected and a printer all are set with manual IP in an active rang of the router 10.0.0.10 - 14 they have to be on manual IP becuse of the ptinter.they cannot connect to the internet but I get the message connected.If I change them to auto IP - they can connect to the internet, the router gives them an IP.
View 3 Replies View RelatedI am looking for Prolink H5305g manual in PDF.
View 1 Replies View Relatedwhat I did do was manually set my IP address for my laptop for my wireless. But I no longer needed to do that so I set it back to Automatic. But every minute or so my IP is changing back to 192.168.0.12 which I did change it to, although it is on Automatic. This is my guess to as what it is doing as I have no connection to the internet after about a minute. ipconfig also displays my IP Address as being 192.168.0.12 as well.What I have to do is disable and then reenable my wireless to get it working again.
View 14 Replies View RelatedI would like to get a manual in English for the experia box zte h220n.
View 1 Replies View RelatedWhere can I download the user manaul for this switch, not the quick start guide?
View 1 Replies View RelatedI am having a public IP address and it is not configured on any of the router interface on my Cisco router. I am having 3 internal networks. Is there any way to PAT all these 3 internal networks to this public IP?
View 3 Replies View RelatedA few months back, my computer stopped connecting to networks. Through some process or another, I ended up "fixing" it by manually inserting the ipv4 settings. Apparently that only allows it to connect to my router though, as public wi fi won't work for it. If I leave the ipv4 settings set to automatically obtain information, the computer won't connect to the network. It will stay on the "identifying network" part indefinitely. In addition, I can't connect through the modem directly either, manual settings or not.
Here is the ipconfig while ipv4 is in auto-obtain
Windows IP Configuration
Host Name . . . . . . . . . . . . : Home
Primary Dns Suffix . . . . . . . :
[Code].....
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
Region : Others
I have MR3220 version 2 and HUAWEI E398 stick.It connects to 3G/4G network, but with wrong APN.It seems to me that manualy changed APN can not be applied. [code]
I upgraded wcs to version 7.0.172 and migrated it to new server and ip address. The upgrade was done by install wcs 7.0.172 on new server and restoring a backup. I also upgraded the location appliance from 6.0.101.0 to 6.0.202.0. The wcs can see the location appliance without a problem. The problem occurs when i try to backup the location appliance. The wcs appears to run the backup and completes with a success but i cannot find the backup file in the ftp directory. wcs backup to ftp folder is fine.is a there a way of doing a manual backup the location appliance what logs can i check to see whether the backup is taking place or not?
View 2 Replies View RelatedI am trying to bind Mac address manually to IP in Cisco 881 router so that if user wants to change the IP address also they should get the same IP.
I have configured as below but it is not working.
ip dhcp pool Test
host 192.168.0.10 255.255.255.0
hardware-address xxxx.xxxx.xxxx.xxxx
this IP was excluded from dhcp range
ip dhcp excluded-address 192.168.0.10
WRVS4400N needs to be manually connected when the power is recycled after power failure. Is there a setting to connect an IPSEC VPN automatically, instead of manually going in to connect the VPN
View 3 Replies View RelatedI have a Buffalo WHR-G300N router & I am having probs with assigning a static address to a nas device.I have set up the static ip address i want to use in the nas When I look at the dhcp leases in the router, the device shows up as having an automatic assignment with a different ip address to the one set in the nas.If I manually assign the ip address which I want to use, or, if I edit the automatically assigned entry, the old one stays as an automatic assignment. This means that I then have 2 ip addresses for 1 mac address.When I try to access the nas, with only the automatically assigned address present in the router settings, I can still access it using the ip address I have manually assigned to the nas, even though the manual ip does not show in the router.How can I delete the automatically assigned dhcp lease & just keep my static one??
View 2 Replies View RelatedI've been having this problem with my Belkin router since day 1 when i got it.( not new, got from buddy's place) It's Belkin HI Speed Wifi G router, and what's really frustrating is, everytime i connect to it, I need to manually change the DNS address and switch between 4.2.2.2 & 4.2.2.4 in order to get internet access! Sometimes it even cuts off the internet during a session, without me even disconnecting from the wifi network, where I would again need to switch back and forth to the 2 or 4 ending!
View 3 Replies View RelatedI don't think I ever set up my laptop for home WIFI. There is only one choice, (being Belkin) in Home Group and would like to take my puter to another room in my house using my WIFI modem occasionally. It did work fantastic at a friends house hooking up to their WIFI. I have been looking for a manual to download, but can't seem to find one on line or at the Acer home page.
View 1 Replies View RelatedWestern digital wd livewire powerline av network kit manual?
View 1 Replies View RelatedMy laptop have 2 NIC attach it, the cable NIC and Wireless NIC, the cable one connect to my lab network environment and the Wireless connect to office network environment (connect to internet) which both have differen segments [code] when my Wireless was turn off my pc can ping to all segment on my lab network environment, but if the wireless was turn on, i cant ping to others segment but only my laptop segment and i still could surfing to the internet without any problem.then i tried to add a new route from my laptop using "route add x.x.x.x mask x.x.x.x (gateway)" in command line and after that i can ping back to all segment in my lab network environment eventhough my wireless was onwhy i have to create a manual route into my laptop so that i can have connection between my laptop and my lab environment in the condition my wireless turn on ??
View 8 Replies View RelatedI was trying to set this up pointed out a back window, but obviously ran into the IR lights reflecting back on the glass. I don't have an external IR light yet, but just tried the manual IR mode and the IR lights stay on.
View 9 Replies View RelatedI keep on getting this error from my adapter I am trying to install. Here is what I copied.
Error description: Invalid key Manual
Model name: AE3000
Operating system: Windows 7 SP 1
Software version: 1.0.0.3
The password I had from my connection is correct. I checked it about 3 times, and it keeps on saying it is wrong? Does this mean I have to reset my router?