Well, a while back, I posted about getting a Network Peripherals KeyStone24MG, and now I have a 9-pin RS-232 cable to connect via console. Now what do I do? I connect with hyperterminal on COM-1, and it only shows a white screen :/
View 1 RepliesIn our premises i want to configure cisco 2960G 24 port switch using hyper terminal commands.
View 1 Replies View RelatedI am still not able to get internet access through my network switch. Where I want to have the switch, I have a TV (with LAN port), PS3, a network capable hard drive, and a iMac. I want to be able to connect the switch to the ethernet jack on the wall and then connect the components to the switch. So here is a map of what I want to do:Actiontech Router (FIOS standard) ---> LAN port on the wall ----->D-Link DGS-1005G switch---->PS3,hard drive, iMac, TV.When I try this setup, everything looks fine, but I do not have internet access. When I connect directly to the wall jack, I always get internet connection. I have tried two different switches, but still no avail.I have tried assigning static IPs to each of the systems, but have had no luck in getting them to connect. The LAN jack is wired directly into the actiontech router. The range on the router is 192.168.1.10-192.168.1.256 (192.168.1.2 is a dd-wrt range extender).
View 7 Replies View RelatedI have 24 port switch which is already connected to internet through static IP. Now I want to use a router as a wireless device to use internet. How do I connect router to switch?
View 3 Replies View Relatedmy computer doesn't have a COM port, so i connected an EthernetCOM cable to my laptop (ehternet end) and COM to the switch. Question now is, how can i establish connection?
View 2 Replies View RelatedHere is a second paragraph from official BCMSN book page 93:
View 6 Replies View RelatedIm looking to connect up 4 new pcs to network but I don't have enough wall ports. I thought I could plug cisco 2950 switch into the port on the wall and act like a hub. The switch configuration is default and there is only one vlan. How is it that it won't connect. Does it need a crossover cable.
View 3 Replies View RelatedI have switch.Broadband connection i want to share it among all 5PCs.By ising ICS and switch can do it??
View 1 Replies View RelatedThe network card in my PC supports 1Gbit ethernet, my 2TB NAS also supports 1Gbit ethernet, however both of these are currently run through a 100Mbit cable modem/router thus reducing the connection speed. I was wondering if I purchased a 1Gbit switch and connected all my devices directly into that, then connected it into the cable modem, would the PC communicate with the NAS directly via the switch or would it go through the cable modem?
View 8 Replies View RelatedI have 1 Cisco switch 24 ports and 12 computers. The 12 computers are divided in three groups and every group is a different network segment.
question 1: I need that every group has communication with its own set of computers but no communication with the computers on the other segments.If I connect the computers to any port on the switch, can they communicate within its own groups? Can the switch pass the network traffic for all of them?
question 2; What I need to do on the switch to have them to reach the internet?
I'm new here but I'm not really new to networking. I manage small network but I just found out that I have some issues regards to speed.So what's the problemAs a main router/fw we have Fortigate 100A which then goes to a core switch SRW2016.This switch then handles two VLANS.The problem is that I have ports 5 assigned to VLAN 100 and port 6 to VLAN 101. They relate to DMZ1 (VLAN100) or internal (VLAN101).When I connect small unmanageable switch to port 5 I get very low performance (20kB/s internet, 2-3MB/s LAN) however when I plug in PC directly, I'm getting full speed.Port 6 with VLAN101 has the same unamangeable switch but no issues.Obviously you're thinking it's the switch - well I've tried replacing it allready. It's not the switch.Both ports have the same configuration (relating to their VLAN) but resolving it goes beyond my knowledge
View 12 Replies View RelatedA Layer 2 switch with IP Address 192.168.1.4 (Vlan0), subnet 255.255.255.0 is physically connected to ADSL Router with IP address 192.168.1.1 (which is also the gateway address for the switch). The problem I have is that all the devices connected to the switch can intercommunicate but are unable to communicate with devices connected to the Router. I guess this may be something to do with how the Vlan is configured on ADSL router?
View 1 Replies View Relatedthere are more than 15 servers which include xen,esx,vmware,also san etc..which are connected to L3 core switch directly. And vlans are created for each.....xen,iscsi,vmware,xen,server. wanted to know is there any other technology other than directly connecting servers to core switch and assigning vlans that can be used in place?
View 4 Replies View RelatedI connected a switch and the device is not even recognized in my router site.
View 12 Replies View RelatedI have two public IP's entering a location from two different sources. One is under our control and the other is a 3rd party. Lets say Ours: 1.2.3.1 3rd Party 1.2.3.2
One is coming in through a firewall/router and the other is a direct link. Each will come into a different network segment 192.168.200.0/24 and 192.168.210.0/24
some of the hosts one subnet will need to talk to the other.
My envisioned setup would be as follows.
1.2.3.1 will come in to the firewall/router into the managed switch. 1.2.3.2 will come in the the same switch but in a vlan The vlan will have a trunked port to the firewall/router to allow routing between the vlan (192.168.210.0) and the other subnet (192.168.200.0).
pxe server ip address is 10.10.10.20 which is connected to switch port fa0/9 and client is connected to switchport fa0/7.i have only 3 devices altogether. below is running config of switch. wen i boot the client from the server, it display error message as: "proxy dhcp were offered. none dhcp were received. exiting broadcom pxe."
Switch#sh run
Building configuration...
Current configuration : 2710 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption[code].....
Is this a good idea to connect access layer directly to core layer with fiber and omit the distribution layer?
View 2 Replies View RelatedI want to connect internet via telephone cable by using rj11 jack from my ethernet switch to another computer it is 150mts away from my office premises.
View 1 Replies View RelatedHave a Linksys E4200 router located in my basement and I am experiencing a puzzling wired connectivity issue as follows: Port 1 on the router is for my study, I have no problem getting connection regardless if I use my study's Ethernet jack or if I run a 5 ft. cable (hereinafter THE CABLE) from the router’s port 1 to my laptop (i.e., cabling does not make a difference).I then connect to router port 1 an EZXS55W Linksys switch (using port 1 on the switch and THE CABLE) and then connect my laptop to port 2 on the switch using a second cable. I am unable to connect to the network/internet even after rebooting both the cable modem and router.I then reconnect my study to port 1 on the router, I go to my study and connect the study’s Ethernet jack using THE CABLE to port 1 on the switch and using a second cable from port 2 on the switch to my laptop. …. I get an network/internet connection immediately ! FYI, I have had the exact problem with switches EZXS88W and SE2500 (no longer own this).
View 5 Replies View RelatedI have a 3560 series switch and two comcast cable modems. I connected the modems to them switch via cross over cables and set an OSPF routing on their subnets. I connected my wireless router to another port of the switch and set its gateway IP on the switch port. I can ping the modem with the switch and I can ping the wireless too. But I cannot access to the Internet via the wireless router.
I need load balancing on two cable modems and get a single network connection via the wireless router.
I want to buy a WRVS4400N, but I need to know something before.
The router will serve as an access point for 10 wireless station, 6 of them will run over Terminal server, the router will also serve 20 computer for the internet, so I want to Link aggregate the four LAN port to my swtich, I know how to do it on my Dell Powerconnect, but I want to know if the WRVS4400N will support it, there will be a lot of traffic going through the router so linking the 4 port in LAG mode to my Powerconnect swicth will speed up the communication !
I use a GS608v2 for my network. I have several wired PC's and laptops. All of them factory 1Gb. I recently upgraded a Dell PC with a Intel 1000GT adapter. The adapter will not detect 1Gb and when forced to 1gb does not connect. I triple-checked cables. The same Cat6a cable works for an other PC. I also tried a different cable. Same result. I also disabled the firewall on the PC with no better results.
View 10 Replies View RelatedAre there any solution to connect VLAN 1002 configured in non-cisco switch to connect to Catalyst 6509?
View 2 Replies View RelatedI have a Cisco 2811 router with C288nm-advsecuruityk9-mz.151-4-4.M.bin IOS version.The router has two LAN interface FE 0/0 and FE 0/1.The router have too, two interfaces ADSL ATM0.0.0 and ATM 0.0.1, both are connect to internet..I need the next configuration.The interface FE 0/0 is directly connect to a Switch A.The interface FE 0/1 is directly connect to a Access Point Cisco.The Access Point and the Switch is not connecting between.The subnet of Switch A and AP are different (Switch A 192.168.180.0/24 and AP 192.168.181.0/24)The devices in the switch A have dynamic IP address, the router must be a DHCP pool to assign theses IP.The device in the AP have dynamic IP address, the router must be a DHCP pool to assign theses IP.I created two DHCP pools in the router, one for the subnet 192.168.180.0 and other for 192.168.181.0, but the devices of FE 0/0 assign IP of 192.168.180.0 or 192.168.181. 0, but not only in the 192.168.180.0.
View 5 Replies View RelatedI connected my 2504 wlc with my 3750-x switch using port-channel. Later i came to know that LAG mode is not supported in 2500 series , so i removed port-channel from my core switch and connected all the 4 port in WLC to core without any port-channel. Is that recommended?
one more thing is , from WLC i can ping tha management interface on my core. but i cannot ping the default-gateway of my dynamically created interface on my WLC to core(core is the defauly gateway for all).
I've had my network up and running for several years with no issues. Last week I upgraded my router to a Dlink 826L and now anything connected to my downstream Dlink DSS16+ can't be accessed.
View 3 Replies View RelatedI am having a bit of trouble. I have a Belkin router (this is irrelevant) across the house, which is extended by the Belkin wireless bridge/repeater in my bedroom. The device in my room boosts my WiFi signal for my MacBook and iPhone, and the LAN (ethernet) port on the back allows my Debian server to connect to the network and internet. I have a Linksys switch that I wish to use, for I have another computer that requires an ethernet connection. Here is what happened:Debian 1 is connected via ethernet, no problem.I shut it down, unplug cable. Run cable from bridge to switch's uplink.Plug another ethernet cable into port one on switch, run it to Debian 1.
View 1 Replies View RelatedI have a Dlink Wireless N Xtreme DIR-655 I have run out of port 4 on it to a switch with a cat 5 patch cable that is 25 ft long It is connected to the Internet port on a Dlink 4 port switch. When i run from that on any of the 4 ports back to my computer ( Win7). I get no internet access but if i connect the cable straight from the router there is no problem. I even attempted to use a older dlink router for the switches and no luck there at all. Any reason the internet would not be broadcasting through the switch.
View 3 Replies View RelatedThe router will serve as an access point for 10 wireless station, 6 of them will run over Terminal server, the router will also serve 20 computer for the internet, so I want to Link aggregate the four LAN port to my swtich, I know how to do it on my Dell Powerconnect, but I want to know if the WRVS4400N will support it, there will be a lot of traffic going through the router so linking the 4 port in LAG mode to my Powerconnect swicth will speed up the communication
View 1 Replies View RelatedAll of a sudden, the router's internal ethernet switch has started to get very slow at connecting to local machines. I can observe the connection fading in and out on each connected machine for up to half an hour until it gets stable. None of the settings have been changed lately.When I use WI-FI, the problem doesn't occur.
View 2 Replies View RelatedThis is for a short temporary time until I get cisco 3560s in place. I have a 2921 configured and it is connecting to an HP non managed non VLAN switch and I cant get any traffic to pass from my computer to the router (pings or anything). Here is brief configuration that should be enough. [code]
Here are my vlans 1-default, 2-management, 192-data, 92-voice, i believe its running rapid spanning tree protocol. Do i have to take off encapsulation on my data vlan to get it to work or make the data vlan default vlan for everything. I am lost as to why this is not working.
I'm trying to connect my router SR520 internal Ethernet port to my ESW520 24 port switch. When I physically connect the cable the port on the switch suddenly drops.
View 1 Replies View RelatedI added Linksys RV-016 16-ports VPN Router into the connection. RV-016 supported multiple subnets.
As mentioned in [URL], D-Link DIR-615 needs to be a device which could support multiple Vlan subnets. But unluckily DIR-615 does not support multiple Vlan subnets.
Therefore I added Linksys RV-016 in the the combination of devices. As what i found in RV-016 GUI setting, it supports multiple subnets.
Purpose outline:
1. Have to create two different SSIDs.
- SSID 1 for Management (able to view all other LAN devices)
- SSID 2 for guest and staff (unable to view all other LAN devices)
2. Create two VLANs in catalyst 2960s.
3. Create two subnets in Linksys RV-016 to accept two Vlans from catalyst 2960s.
Any experience of configuring RV-016 for the mentioned purpose above?