I'm having trouble with my internet the past few days, I'm connected to the internet via wifi and after browsing some minutes it will tell me unable to connect (using firefox and other explorers). In order to continue browsing I must refresh the page several times and it will load without pictures.I'm using win7 home premium and it's the only computer that presents this issue. I've tried pluging the computer directly to the router, but it gives me the same results. Also, I've scanned the computer for malware with MCafee, but it shows nothing.
In 802.1x I am having an issue where the computers un-authenticate if you remote desktop to them (they are signed in with the same domain account that is being used to remote connect with).
Any of ya'll out there that have done 802.1x run into this issue before?
I will be moving away from my home computer but will still want access to it so I am trying to set up a VPN between it (home computer is windows 7) and my fedora 15 machine. They are currently on the same 192.168.1.0/24 network so I'm wondering if that may be the cause for my troubles.
Here's my setup:
Fedora 15 (192.168.1.3) is running the PPTP server with pptpd and gives 192.168.1.66 to any vpn client that connects to it./etc/pptpd.conf only has "localip 192.168.1.3" and "remoteip 192.168.1.66" options in it /etc/ppp/options.pptpd has "refuse-pap, refuse-chap, refuse-mschap, require-mschap-v2, require-mppe-128, proxyarp, lock, nobsdcomp, novj, novjccomp, nologfd, debug, dump" options Windows 7 (192.168.1.6, 192.168.1.66) is the client and I have it set to use connect to the public IP address of my router, PPTP, require encryption, only allow mschap-v2, don't use gateway in ipv4 properties.Both machines are connected to the same Belkin router (192.168.1.254) and I can ping locally to and from each computer no problem. The problem is my VPN connection is very inconsistent. I will open a ftp connection to 192.168.1.66 from 192.168.1.3, login, start uploading a file, get about 10MB uploaded, and then the VPN connection will die and the upload will fail. But, when I have "ping 192.168.1.66" running while uploading, the connection stays alive.
Is the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
At first it seemed to happen everyday at the same time, but now seems completely random (happening twice a day somedays). At some part during the day while the user is busy with this system it drops the network connection. The ONLY way to get it back is by restarting via the reset button. Shutdown or even logoff just hangs. Nothing regarding that card will work or respond, you can not even disable and re-enable. I can however get the wireless to work without restarting. I've done everything I could possible think of including format and re-installing Windows. Something new I've noticed is that the user always has MS Access (in runtime mode) running while network goes down and then you can not end that process.
I have just upgraded from 20mb to 100mb internet with virgin media and ever since then when ever i try download any thing it start's downloading at a high speed then it slowly decreases until it dies out and stops like this
I tried a speed test to see what i was receiving it started at 100mb/s then it started to go down stopped for a sec then shot down to 10mb/s like this
When I am playing a game or watching a video on youtube or twitch it's fine streams with out needing to buffer only time i notice this is when i try to download some thing
windows update did its thing but as soon as it finished downloading and started installing my AVG anti-virus pop'd up requesting to move some files to "the vault", when that happened windows finished installing and asked my computer to restart, after it restarted i tried to go on AIM and Ventrilo (aka Vent), here's i knew something was wrong, I couldn't sign in to AIM all it said was "waiting for Network..." and Vent just simply said "unknown last ip address" I went to command prompt > ipconfig where it said connection-specific dns suffix it was blank, for ip address it still showed my ip same for subnet mask there was still some numbers but, for default gateway it was blank, thinking it must had something to do with the drivers window installed I did a system restore to two days ago, after it rebooted I thought I fixed it, I was able to sign on AIM as well as Vent even able to use google chrome and watch a friend stream on live on twitch tv, so calling it a night I shut down my PC and when to sleep, now to the title, woke up turned on PC got on AIM and Vent perfectly tried to play Maplestory (don't judge XD i grew up with that game) but it said I had to download the game, made sense to me I just got the game a last night but just did a system restore to 2 days before so I started downloading the game it would work for a few moments but then my internet would die and the same problem that I described would happen again, and the only way i could get my internet to work on my PC was to restart the computer?
I download drivers from Nvidia website it self so i did and it said my motherboard drivers were out of date, I downloaded the drivers and installed them, the Nvidia guid said it would uninstall the old drivers and restart the computer and install new drivers but, when the computer restarted it said something about there were other wizerd installings ? and press okay to minimize the prosses so I can close those, I tried but it did some kind of loop saying again that it would unistall and install after restarting and again like last time said there were other programs running, this time i clicked exit, I went back to Nvidia site to see if the drivers for the motherboard installed, the versions matched but the site did state "your drivers are up to date" like it normally would just asked if I wanted to down load the driver as if my motherboard was still out of date?
Tech Support Guy System Info Utility version 1.0.0.2 OS Version: Microsoft Windows XP Home Edition, Service Pack 3, 32 bit Processor: AMD Athlon(tm) 64 X2 Dual Core Processor 5000+, x86 Family 15 Model 107 Stepping 2 Processor Count: 2 RAM: 2047 Mb Graphics Card: NVIDIA GeForce 8800 GT, 512 Mb Hard Drives: C: Total - 76308 MB, Free - 25295 MB; Motherboard: ASUSTeK Computer INC., M3N78-VM Antivirus: AVG Anti-Virus Free Edition 2011, Updated: Yes, On-Demand Scanner: Enabled
Bought a Vostro 220S about 2 months ago. After about three weeks, while I'm using it, the integrated NIC dies. All of a sudden I get the "Network Cable Disconnected" pop-up. No LEDs lit by the network jack. Contact Dell support who decides it's the motherboard.Three days later, the exact same failure. Contact support again. This time they want me to re-install Windows (yeah...right). I refused since the motherboard fixed it the first time. They finally agree to replace the motherboard again. Using the same router and cable that worked for years with my old computer. After the first failure, I switched ports on the router. While waiting for the motherboard replacements, I had installed an old PCI NIC I had laying around. Worked fine...still is. I'm not about to re-install Windows, which is what I know they'll want. I'll stick with the PCI card. Both of the people at Dell support as well as the tech they sent out told me they've not seen this before.
I have two WAP4410N wireless access points powered using Power-Over-Ethernet. Both are running the latest available firmware version (2.0.5.3)They are both connected to the same LAN and broadcasting the same SSID with a WPA2 password.
One is using channel 1, while the other is using channel 11.There is coverage overlap where the signal from both access points hover around -75db to -85db while standing in the same physical location.DHCP is disabled, and is being provided by another network device.
Every day or so, devices can connect and authenticate to the access points, but are not granted an IP address (and subsequently are unable access to the LAN or Internet). For devices that had already retrieved an IP address prior to the issue exhibiting itself, the devices simply stop communicating with LAN and Internet.
However, I can still access each access point's web admin interface from the LAN.
If I reboot both devices, the problem vanishes and devices are once again able to get an IP address and connect to the LAN and Internet.Are these symptoms of signal interference between the two WAPs or is this a completely different issue?
When my Hp Desktop with Vista starts up,... the internet for everyone in the house goes out and the phones go out as well because our modem controls the internet and phone. The modem shows the DNS light blinking. When this Hp desktop is turned off I have internet and phone in the house. I just have no idea why the desktop turning on, causes the internet and phone to shut off...
I've got a Cisco DPC3825 modem that I also use as a wifi router. Conntected to it I have 4 eithernet cables:
1. From PC to Router
2. From another PC to router
3. From TV to router
4. From a Dlink Powerline Adapter to Router.It took me a while to figure this out but when I unplug all the eithernet cables and plug back in #1 and #2 (from above) the internet works. When I plug back in #3 and #4, the internet dies. Meaning, I am connected to the network but not the internet. I've reset the modem, changed SSID and restarted the PC many times but still can't figure out this issue.
I got an Apple TV a few weeks back and we've been using it a lot, especially to stream Netflix. However, another application that I got it for was for streaming iPhoto slideshows and iMovie stuff to the Apple TV with Airplay's screen sharing. This event scenario has played out several times..... Screen sharing is up and going and it'll be working great. All of a sudden the TV will go back to the main Apple TV menu on its own. Upon further review at this point, NONE of my WiFi (iPhone, iPad, etc.) devices will connect to the network and I have to power cycle the router. Router lights are on, but no one's home. At this point, it'll boot back up and then everything will be fine, at least for a while.Tonight, I was showing vacation pictures to some family and this same process happened twice. Since I can't seem to figure out how to stop playing a slideshow in iPhoto and then start it again in the middle, it's very annoying. Here are some relevant troubleshooting points to consider:
1. This network problem (or something similar to it) has happened in the past, but whatever it is, streaming a slideshow really seems to aggravate it. This seems to be the only scenario that I can do to actually INDUCE the issue. Periods of long uploads or downloads are fine. Streaming audio from one device and similar usage seems to be fine, but this scenario fails pretty much every time, and not necessarily right away.
2. After having this issue tonight multiple times, I stopped trying to stream an actual iPhoto slideshow and just went into the album and scrolled through the pics one by one. I did this for at least an hour with no issue. But with an actual slideshow, it failed twice in 30 minutes or less. And it's happened before tonight as well.
3. It doesn't appear to make a difference what application I'm streaming from on the Mac. Whether it's iPhoto, iMovie, or even Facetime.
-MacBook Pro Specs - OS X 10.8.2 - Late 2011 Model -Apple TV - MD199LL/A, v5.0.2 -Router - Linksys/Cisci E1000 - Firmware v2.1.02
I've got a fair amount of devices in my home that use WiFi, but there was nothing irregular going on in the house to generate an excessive amount of internal network traffic or anything like that. My gut says the problem is with the router, but it's only a few months old, and I've updated the firmware to no avail.
Region : UnitedKingdom Model : TL-WR1043ND Hardware Version : v1 Firmware Version : TL-WR1043ND_V1_120405 ISP : BT Infinity (1)
I have a TL-WR1043ND v1 with the latest firmware installed TL-WR1043ND_V1_120405.I loose access to the router (can't see web page, can't config, can't restart).I have a Linux server on the Ethernet, and uplink through 200Mbps powerline adapter to the BT Infinity modem. A few other devices on the wireless.The router works well and I prefer it to the BT Home Hub 3 for fiber because it proved to be faster in many cases as tested.But after a few days the web interface becomes inaccessible. It's like the web server died or something. Browser says connection reset, if I try telnet to port 80 says connection refused.Actually I just did a full netcat scan (sudo netcat -z -v -192.168.1.1 1-65535) and all ports say connection refused.Ping works - I can ping it allright.DHCP server works too, just restarted a computer and got IP from the router.Port forwarding works as well and DynDNS seems to work as well as my ISP changes the IP periodically and I can always find the updated one.All works - exept I can't access the router in any way!If I restart (remove power and plug it back in), it boots and I can access the router again.So restarting won't work remotely, I actually have to go home to re-plug it!
I have wrt610n that i have wd 1 tb drive hooked to usb port and when i try to copy large folder/files to it, i get the dreaded- cancel, try again skip and it locks up solid. i have treied all settings in these and other forums. i have tried two different brand size hard drives, i have tried wireless and wired and nothing. is there a fix for this. i have latest firmware on everything, i have everything set tweaked best as they can and not one things makes a differance. all i get from linksys is try this try that. is there a way to copy large files to hd first via the pc then hook back to the router to see the files?
When my download starts or reaches half way the internet connection stops. How to keep the net connection connected all the time? and specially during downloads?
I have remote access as I work at home on a government laptop that has Entrust( for security). My IP lapse time is set for 1 hour and every hour I am losing full connection due to having to sign back into Entrust. I need to be able to lenghten my lapse time on my work computer. My other two personal computers are fine with 1 hour as there is no Entrust on either of those laptops.....is it possible for me to change the lapse time to say 12 hours, 1 weeks, whatever??
I am using a desktop computer and have the router downstairs so I am using a wireless usb to connect to the internet. My router is a Linksys E1000 and the wireless adapter is a Netgear WG111v2. The problem is Every few mins I drop connection for may 5-30 secs and then the internet is fine. During that time it does not say I only have local connection or anything like that it constantly says I have internet connection even when I dont. It is very noticable when i am playing an online game on my computer. I will get a few mins in and then it will drop kicking me out of the game and by the time I get kicked out my Internet is reconnected and I can join again.
I lose internet connection every day in the same time etc.i lose it in 2pm and i get it in 7.pm and tomarow again lose it in 2pm get it in 7pmit is not virus i have cleaned every infection whit Malwarebytes,Emsisoft,Hitmanpro,SuperAntispyware and Spybot
I lose every day internet in the same time etc.in 2 pm and tomarow again in 2pm and also i get in the same time etc i lose internet in 2pm and i get internet in 7pm and tomarow again i have caled my ISP and it is not problem whit it also it is not virus.
It is usually by a router or install a third party software without anyone saying if it works or not.
I have two connections at home. One is a Wifi ( public wifi for my village) that i use for my phone and the other one is a wired dsl. I have used both but not on the same time. I tried connecting them both ( phone have tethering) but I think they are interfering with each other making me lose connection. I am using vista home.
I have seen the merge connections( in network and sharing center) and i have seen this one [URL].. but I am a little bit wary of changing my registry.
At around 2:30 PM each day, the internet slows down, and it says its connected but with limited access. A few minutes later, it gets full connection again, but it is super slow, then the same cycle starts over again. It stops happening around 8:00 PM.
Internet cable to dir655 and cat5 to master computer with slave using wireless. Network between them always works fine. But if master connects to internet the slave will lose the internet until the master disconnects. like it won't share the signal.
I set up my Linksys wireless router BEFW11S4 with a password protection to prevent access from unauthorized users, now I can only access my internet connection from one computer at a time not simultaneously like before I introduced the password. I must have missed to turn on a switch somewhere in the set up
I am using my ADSL Internet Connection especially for downloading files those past few months.I have even purchased an account at filesonic.However,the speed remain the same except that there are no waiting period and I can download multiple files at the same time.What are the tips for increasing downloading time? I am now using the latest 5.0 Firefox and Windows 7 and using or not using the download them all add-ons does not add much to the download time.
What about the telephone line cable? The position of the beetel modem, does that play a role in speed limit? Are there some hardware equipment that can cause a subsequent increase in download speed?
For some reason, certain activities, such as using Bittorrent and visiting specific sites, causes my connection to drop immediately. It stays down for five minutes, after which the connection is reestablished... but if the offending progam is still running or I try to refresh the site, it drops for another five minutes.I really need to know what is causing this, and how it can be avoided. It only started this last weekend (22/1, 2011), and my ISP says they have no problems on their end. I'm running Windows 7.
I am running a Cisco 878-K9 Router, IOS 12.4(11)T1, as a Firewall with EasyVPNServer. The VPN Server was created with the wizard from the SDM.Everything works fine, BUT the VPN connections fail after about 10 minutes.
How to block Internet Connection during specific time.for example i want to block everyday between 8am to 12nn, then 1pm to 5pm.what are the options and better to achieve this kind of policy??
I have two routers one is a o2 router which is for the internet (broadband) the other is an old bt home hub which i have connected to the printer via usb. In order to print a document at the moment i have to disconnect my laptop from the broadband router and connect it to the printer router.Is there any way that i can connect to the two router s at the same time so that i while printing i can still keep my internet connection.
I am facing a proble in wireless connection speed that is getting very slow at a specific time, i.e., from 12pm to 2pm and from 9 pm to 2 am. The service is unlimitted type contract
I set up an IPSec VPN with NAT-T between two cisco router 871. In particular one router acts as a SERVER and the other one as a CLIENT. All the traffic coming from the hosts connected to the CLIENT-router is sent over the VPN (no split tunnel). Everything works perfectly. The only problem is the amount of time the VPN takes to establish the first connection between the two routers. In particular it takes about two minutes. tell me if this amount of time can be reduced (with a partcular configuration instruction)? Or this is the minimum amount of time required for the first connection establishment?
I have a cisco 2021 router and I configured firewall and Site to site VPN on it, but recently Ism experincing and issue with, I have dropping in the connection and this issue, this make the VPN connection to have a slow performance and some time disconnection.
